La3+ and F- dual-doped multifunctional hydroxyapatite nanoparticles: Synthesis and characterization

Synthesis of biocompatible Ti-6Al-4V composite reinforced with ZrO2 and bioceramic produced by powder metallurgy: Morphological, structural, and biocompatibility analysis

In this experimental study, the initial phase involved preparing composite structures with various mix ratios using the Ti-6Al-4V alloy, widely used in clinical applications, in conjunction with ZrO2 and hydroxyapatite (HA) synthesized via the precipitation method, employing powder metallurgy techniques. Subsequently, the microstructures of the resultant hybrid composite materials were imaged, and x-ray diffraction (XRD) phase analyses were conducted. In the final phase of the experimental work, tests were performed to determine the biocompatibility properties of the hybrid composites. For this purpose, cytotoxicity and genotoxicity assays were carried out. The tests and examinations revealed that structures compatible both morphologically and elementally were obtained with no phase transformations that could disrupt the structure. The incorporation of ZrO2 into the Ti-6Al-4V alloy was observed to enhance cell viability values. The value of 98.25 ± 0.42 obtained by adding 20% ZrO2 gave the highest cell viability result. The addition of HA into the hybrid structures further increased the cell viability values by approximately 10%. All viability values for both HA-added and HA-free groups were obtained above the 70% viability level defined in the standard. According to the genotoxicity test results, the highest cytokinesis-block proliferation index values were obtained as 1.666 and 0.620 in structures containing 20% ZrO2 and 10% ZrO2 + 10% HA, respectively. Remarkably, all fabricated composite and hybrid composite materials surpassed established biocompatibility standards and exhibited nontoxic and nongenotoxic properties. This comprehensive study contributes vital insights for future biomechanical and other in vitro and in vivo experiments, as it meticulously addresses fundamental characterization parameters crucial for medical device development. RESEARCH HIGHLIGHTS: Support of optimum doping rates ions on hybrid composites and concentrations. Development of uniform surface appearance and distributions/orientations of microcrystals on ceramic compounds Improvement of cell viability and desired increase in biocompatibility with the doping of HA.

Resorbable membrane design: In vitro characterization of silver doped-hydroxyapatite-reinforced XG/PEI semi-IPN composite

In this study, the production and characterization of silver-doped hydroxyapatite (AgHA) reinforced Xanthan gum (XG) and Polyethyleneimine (PEI) reinforced semi-interpenetrating polymer network (IPN) biocomposite, known to be used as bone cover material for therapeutic purposes in bone tissue, were performed. XG/PEI IPN films containing 2AgHA nanoparticles were produced by simultaneous condensation and ionic gelation. Characteristics of 2AgHA-XG/PEI nanocomposite film were evaluated by structural, morphological (SEM, XRD, FT-IR, TGA, TM, and Raman) and biological activity analysis (degradation, MTT, genotoxicity, and antimicrobial activity) techniques. In the physicochemical characterization, it was determined that 2AgHA nanoparticles were homogeneously dispersed in the XG/PEI-IPN membrane at high concentration and the thermal and mechanical stability of the formed film were high. The nanocomposites showed high antibacterial activity against Acinetobacter Baumannii (A.Baumannii), Staphylococcus aureus (S.aureus), and Streptococcus mutans (S.mutans). L929 exhibited good biocompatibility for fibroblast cells and was determined to support the formation of MCC cells. It was shown that a resorbable 2AgHA-XG/PEI composite material was obtained with a high degradation rate and 64% loss of mass at the end of the 7th day. Physico-chemically developed biocompatible and biodegradable XG-2AgHA/PEI nanocomposite semi-IPN films possessed an important potential for the treatment of defects in bone tissue as an easily applicable bone cover. Besides, it was noted that 2AgHA-XG/PEI biocomposite could increase cell viability, especially in dental-bone treatments for coating, filling, and occlusion.

Fabrication of mechanically advanced polydopamine decorated hydroxyapatite/polyvinyl alcohol bio-composite for biomedical applications: In-vitro physicochemical and biological evaluation

In this study, polydopamine (PDA) coated hydroxyapatite (HA) reinforced polyvinyl alcohol (PVA) films were produced to be used in biomedical applications such as bone tissue regeneration. pDA is coated not only to prevent the agglomeration of HA when encountering interstitial fluids but also to strongly bind the PVA for the interaction between materials so that the mechanical performance becomes more stabilized. pDA was coated on the hydroxyapatite surface using a radical polymerization technique, and the reinforced PVA were produced with pDA-coated HA (pDA-HA/PVA) nanoparticles. Fundamental characteristic properties of pDA-HA/PVA nanocomposite films were examined by morphological/chemical (SEM-EDS), microstructural (XRD, Ft-IR, and Raman), thermodynamic (TGA and TM), mechanical performance (Vickers microhardness) and biological activity analysis (MTT, genotoxicity and antimicrobial efficacy investigations). Physicochemical analysis showed that all the samples studied exhibited homogeneous mineral distributions through the main structures. According to TGA, TMA and hardness tests, the new composite structure possessed higher mechanical properties than neat PVA. Further, pDA-HA/PVA nanocomposites exhibited high antibacterial capacities against Acinetobacter Baumannii (A.Baumannii), Staphylococcus aureus (S. aureus), and Streptococcus mutans (S.mutans). Moreover, the new nanocomposites were noted to present good biocompatibility for fibroblast (L929) cells and to support remarkably MCS cells. All in all, this comprehensive work shows that the thermo-mechanically improved pDA-HA/PVA films will increase the application fields of PVA in biomedical fields especially tooth-bone treatments for coating, filling, or occlusion purposes.

Effects of Yttrium Doping on Erbium-Based Hydroxyapatites: Theoretical and Experimental Study

This is the first investigation of yttrium (Y) and erbium (Er) co-doped hydroxyapatite (HAp) structures, conducted using theoretical and experimental procedures. By using a wet chemical method, the materials were synthesized by varying the concentration of Y amounts of 0.13, 0.26, 0.39, 0.52, 0.65, and 0.78 at.% every virtual 10 atoms of calcium, whereas Er was kept fixed at 0.39 at.%. Spectroscopic, thermal, and in vitro biocompatibility testing were performed on the generated samples. Theoretical calculations were carried out to compute the energy bandgap, density of states, and linear absorption coefficient. The effects of Y concentration on thermal, morphological, and structural parameters were investigated in detail. Raman and Infrared (FTIR) spectroscopies confirmed the formation of the HAp structure in the samples. Theoretical investigations indicated that the increasing amount of Y increased the density from 3.1724 g cm^-3 to 3.1824 g cm^-3 and decreased the bandgap energy from 4.196 eV to 4.156 eV, except for the sample containing 0.39 at. % of the dopant, which exhibited a decrease in the bandgap. The values of linear absorption appeared reduced with an increase in photon energy. The samples exhibited cell viability higher than 110%, which revealed excellent biocompatibility for biological applications of the prepared samples.

Evolution of dynamics of physico-chemical and mechanical properties of hydroxyapatite with fluorine addition and degradation stability of new matrices

This multidisciplinary study examined sensitively the change in the dynamics of main mechanical performance, stability of crystal structure, crystallinity quality, strength, corrosion resistance, biocompatibility, resistance to structural degradation/separations and mechanical durability features of hydroxyapatite (HAp) biomedical materials based on the fluorine addition and degradation process to guide future medical and dental treatment studies. In the study, the fluorine ions were used to be the dental coating, filling and supporting material for biologically or synthetically produced bone minerals. The general characteristic properties were investigated by means of standard spectroscopic, structural and mechanical analysis methods including RAMAN, SEM-EDS, TEM, Vickers micro-indentation hardness and density measurements. A time dependent release test was performed to evaluate possible fluorine ion release after the degradation process. It was found that the fundamental characteristic properties of HAp biomedical materials are noted to improve with the increase in the fluoride level up to 2% due much more stabilization of HAp crystal system. The combination of RAMAN spectra and powder XRD analyzes indicates that 2% addition level affects positively the formation velocity of characteristic HAP phase. Besides, fluorine doped HAp materials all exhibited the main characteristic peaks after degradation process. This is attributed to the fact that the fluorine ions enabled the hydroxyapatite to enhance the structural quality and stability towards the corrosion environment. However, in case of excess dopant level of 3% the degradation rates were obtained to increase due to higher contribution rate and especially electrostatic interactions. As for the surface morphology examinations, 2% fluorine added HAp with the highest density of 3.0879 g/cm³ was determined to present the superior crystallinity quality (smallest grain size, best smooth surface, honeycomb pattern, regular shaped particles and densest particle distributions through the specimen surface). Conversely, the excess fluorine triggered to increase seriously degree of micro/macro porosity in the surface morphology and microscopic structural problems in the crystal system. Thus, the HAp doped with 3% was the most affected material from the degradation process. Additionally, the fluorine ion values read after the release process were quite far from the value that could cause toxic effects. Lastly, the optimum fluorine addition provides the positive effects on the highest durability, stiffness and mechanical fracture strength properties as a consequence of differentiation in the surface residual compressive stress regions (lattice strain fields), amplification sites and active operable slip systems in the matrix. Hence, the crack propagations prefer to proceed in the transcrystalline regions rather than the intergranular parts. Similarly, it was found that Vickers micro-indentation hardness tests showed that the microhardness parameters increased after the degradation process. All in all, the fluorine addition level of 2% was noted to be good choice to improve the fundamental characteristic properties of hydroxyapatite biomedical materials for heavy-duty musculoskeletal, orthopedic implant, biological and therapeutic applications in medicine and dentistry application fields.

The Relationship between Osteoinduction and Vascularization: Comparing the Ectopic Bone Formation of Five Different Calcium Phosphate Biomaterials

Objective: The objective of this study is to compare the bone induction of five kinds of calcium phosphate (Ca-P) biomaterials implanted in mice and explore the vascularization and particle-size-related osteoinductive mechanism. Methods: The following five kinds of Ca-P biomaterials including hydroxyapatite (HA) and/or tricalcium phosphate (TCP) were implanted in the muscle of 30 BALB/c mice (n = 6): 20 nm HA (20HA), 60 nm HA (60HA), 12 µm HA (12HA), 100 nm TCP (100TCP) and 12 µm HA + 100 nm TCP (HATCP). Then, all animals were put on a treadmill to run 30 min at a 6 m/h speed each day. Five and ten weeks later, three mice of each group were killed, and the samples were harvested to assess the osteoinductive effects by hematoxylin eosin (HE), Masson’s trichrome and safranine−fast green stainings, and the immunohistochemistry of the angiogenesis and osteogenesis markers CD31 and type I collagen (ColI). Results: The numbers of blood vessels were 139 ± 29, 118 ± 25, 78 ± 15, 65 ± 14 in groups HATCP, 100TCP, 60HA and 20HA, respectively, which were significantly higher than that of group 12HA (12 ± 5) in week 5 (p < 0.05). The area percentages of new bone tissue were (7.33 ± 1.26)% and (8.49 ± 1.38)% in groups 100TCP and HATCP, respectively, which were significantly higher than those in groups 20HA (3.27 ± 0.38)% and 60HA (3.43 ± 0.27)% (p < 0.05); however, no bone tissue was found in group 12HA 10 weeks after transplantation. The expression of CD31 was positive in new blood vessels, and the expression of ColI was positive in new bone tissue. Conclusions: Nanoscale Ca-P biomaterials could induce osteogenesis in mice muscle, and the osteoinductive effects of TCP were about 124% higher than those of 20HA and 114% higher than those of 60HA. The particle size of the biomaterials affected angiogenesis and osteogenesis. There was a positive correlation between the number of blood vessels and the area percentage of new bone tissue; therefore, osteoinduction is closely related to vascularization. Our results provide an experimental basis for the synthesis of calcium−phosphorus matrix composites and for further exploration of the osteoinductive mechanism.