Detailed positron annihilation lifetime spectroscopic investigation of atrazine imprinted polymers grafted onto PE/PP non-woven fabrics

Probing the Free Volume in Polymers by Means of Positron Annihilation Lifetime Spectroscopy

Positron annihilation lifetime spectroscopy (PALS) is a valuable technique to investigate defects in solids, such as vacancy clusters and grain boundaries in metals and alloys, as well as lattice imperfections in semiconductors. Positron spectroscopy is able to reveal the size, structure and concentration of vacancies with a sensitivity of 10^-7. In the field of porous and amorphous systems, PALS can probe cavities in the range from a few tenths up to several tens of nm. In the case of polymers, PALS is one of the few techniques able to give information on the holes forming the free volume. This quantity, which cannot be measured with macroscopic techniques, is correlated to important mechanical, thermal, and transport properties of polymers. It can be deduced theoretically by applying suitable equations of state derived by cell models, and PALS supplies a quantitative measure of the free volume by probing the corresponding sub-nanometric holes. The system used is positronium (Ps), an unstable atom formed by a positron and an electron, whose lifetime can be related to the typical size of the holes. When analyzed in terms of continuous lifetimes, the positron annihilation spectrum allows one to gain insight into the distribution of the free volume holes, an almost unique feature of this technique. The present paper is an overview of PALS, addressed in particular to readers not familiar with this technique, with emphasis on the experimental aspects. After a general introduction on free volume, positronium, and the experimental apparatus needed to acquire the corresponding lifetime, some of the recent results obtained by various groups will be shown, highlighting the connections between the free volume as probed by PALS and structural properties of the investigated materials.

Design and Characterization of Carboplatin and Paclitaxel Loaded PCL Filaments for 3D Printed Controlled Release Intrauterine Implants

Uterine cancer is the fourth most common cancer in women. Despite various chemotherapy approaches, the desired effect has not yet been achieved. The main reason is each patient responds differently to standard treatment protocols. The production of personalized drugs and/or drug-loaded implants is not possible in today’s pharmaceutical industry; 3D printers allow for the rapid and flexible preparation of personalized drug-loaded implants. However, the key point is the preparation of drug-loaded working material such as filament for 3D printers. In this study, two different anticancer (paclitaxel, carboplatin) drug-loaded PCL filaments with a 1.75 mm diameter were prepared with a hot-melt extruder. To optimize the filament for a 3D printer, different PCL Mn, cyclodextrins and different formulation parameters were tried, and a series of characterization studies of filaments were conducted. The encapsulation efficiency, drug release profile and in vitro cell culture studies have shown that 85% of loaded drugs retain their effectiveness, provide a controlled release for 10 days and cause a decrease in cell viability of over 60%. In conclusion, it is possible to prepare optimum dual anticancer drug-loaded filaments for FDM 3D printers. Drug-eluting personalized intra-uterine devices can be designed for the treatment of uterine cancer by using these filaments.

Synthesis and characterization of tetracycline-imprinted membranes: A detailed positron annihilation lifetime spectroscopy investigation

Molecularly imprinted thin membranes for selective removal of tetracycline from real water samples were prepared using the radiation-induced polymerization method. The chemical and physical characterization of the membranes was conducted by FTIR, XPS, AFM and SEM analyses. The effect of the template on the size and the size distribution of the pores in the membrane structure was investigated by positron annihilation lifetime spectroscopy (PALS) experiments. The presence of the template molecule causes the formation of larger cavities, which have a strong correlation to the molecular size of the template molecule. The density of the free volume holes in the imprinted network shows a significant increase due to the presence of the template molecule. The binding performances of the membranes were tested against various factors such as pH, time and initial concentration of template molecules. The specific selectivity of the membranes was investigated by cross-reactivity experiments. The binding capacity of the imprinted membranes was obtained at 14.5 μmol g^-1 , with the highest imprinting factor (2.84) for tetracycline. The imprinting factor was obtained at 1.44, 1.25 and 1.57 for oxytetracycline hydrochloride, doxycycline hyclate and chlortetracycline, respectively. The binding capability of the imprinted membranes in real water samples was promising for the application of the membranes as a filter material for removal of tetracycline with high binding capacity. Tetracycline binding percentage of the membranes was determined at 92.4, 81.1., 75.0 and 68.7 for ultra-pure water, tap water and natural water samples collected from different sources, respectively.

Surface modification of magnetic nanoparticles via admicellar polymerization for selective removal of tetracycline from real water samples

Production of imprinted thin membranes via admicellar polymerization

Mechanical characterization and ex vivo evaluation of anticancer and antiviral drug printed bioadhesive film for the treatment of cervical cancer

As research progresses on personalized medicines, it is clear that personalized and flexible formulations can provide effective treatment with reduced side effects especially for diseases like cancer, characteristic of high patient variability. 2D and 3D printers are frequently reported in the literature for the preparation of pharmaceutical products with adjusted dose and selected drug combinations. However, in-depth characterization studies of these formulations are rather limited. In this paper, ex vivo and mechanical characterization studies of antiviral and anticancer drug printed film formulations designed for personalized application were performed. Effects of the printing process with pharmaceutical formulations such as paclitaxel (PCX):cyclodextrin (CD) complex or cidofovir (CDV) encapsulated into poly(ethylene glycol)-polycaprolactone (PEG-PCL) nanoparticles on the films were evaluated through a series of mechanical characterization studies. Inkjet printing process was found to cause no significant change in the thicknesses of the film formulations, while mechanical strength and surface free energy increased and nano-sized voids in the film structure decreased. According to the mechanical characterization data, the unprinted film had maximum force (F_max) value of 15.6 MPa whereas F_max increased to 43.8 MPa for PCX:CD complex printed film and to 37.7 MPa for the antiviral CDV-PEG-PCL nanoparticle printed film. In the light of ex vivo findings of sheep cervix-uterine tissue, bioadhesive properties of film formulations significantly improved after inkjet printing with different drug formulations. It has also been shown that the anticancer formulation printed on the film was maintained at the cervix tissue surface for >12 h. This study has shown for the first time that inkjet printing process does not adversely affect the mechanical properties of the bioadhesive film formulations. It has also been shown that durable bioadhesive film formulations for personalized dosing can be prepared by combining nanotechnology and inkjet printing.