Force analysis of the patellar mechanism

Load transfer in bone after partial, multi-compartmental, and total knee arthroplasty

Introduction: Arthroplasty-associated bone loss remains a clinical problem: stiff metallic implants disrupt load transfer to bone and, hence, its remodeling stimulus. The aim of this research was to analyze how load transfer to bone is affected by different forms of knee arthroplasty: isolated partial knee arthroplasty (PKA), compartmental arthroplasty [combined partial knee arthroplasty (CPKA), two or more PKAs in the same knee], and total knee arthroplasty (TKA). Methods: An experimentally validated subject-specific finite element model was analyzed native and with medial unicondylar, lateral unicondylar, patellofemoral, bi-unicondylar, medial bicompartmental, lateral bicompartmental, tricompartmental, and total knee arthroplasty. Three load cases were simulated for each: gait, stair ascent, and sit-to-stand. Strain shielding and overstraining were calculated from the differences between the native and implanted states. Results: For gait, the TKA femoral component led to mean strain shielding (30%) more than three times higher than that of PKA (4%-7%) and CPKA (5%-8%). Overstraining was predicted in the proximal tibia (TKA 21%; PKA/CPKA 0%-6%). The variance in the distribution for TKA was an order of magnitude greater than for PKA/CPKA, indicating less physiological load transfer. Only the TKA-implanted femur was sensitive to the load case: for stair ascent and gait, almost the entire distal femur was strain-shielded, whereas during sit-to-stand, the posterior femoral condyles were overstrained. Discussion: TKA requires more bone resection than PKA and CPKA. These finite element analyses suggest that a longer-term benefit for bone is probable as partial and multi-compartmental knee procedures lead to more natural load transfer compared to TKA. High-flexion activity following TKA may be protective of posterior condyle bone resorption, which may help explain why bone loss affects some patients more than others. The male and female bone models used for this research are provided open access to facilitate future research elsewhere.

[Isolated Patellofemoral Osteoarthritis]

Isolated patellofemoral osteoarthritis is a complex pathology. It occurs frequently in women over 40 years and leads to a high degree of suffering. The causes of femoropatellar degeneration are manifold and require stage-specific therapy. This is very challenging for the treating physician. This article is intended to provide a structured overview of the symptoms, diagnostics and stage-specific therapy of patellofemoral osteoarthritis.

Computational biomechanics of human knee joint in stair ascent: Muscle-ligament-contact forces and comparison with level walking

About a third of knee joint disorders originate from the patellofemoral (PF) site that makes stair ascent a difficult activity for patients. A detailed finite element model of the knee joint is coupled to a lower extremity musculoskeletal model to simulate the stance phase of stair ascent. It is driven by the mean of measurements on the hip-knee-ankle moments-angles as well as ground reaction forces reported in healthy individuals. Predicted muscle activities compare well to the recorded electromyography data. Peak forces in quadriceps (3.87 BW, body weight, at 20% instance in our 607 N subject), medial hamstrings (0.77 BW at 20%), and gastrocnemii (1.21 BW at 80%) are estimated. Due to much greater flexion angles-moments in the first half of stance, large PF contact forces (peak of 3.1 BW at 20% stance) and stresses (peak of 4.83 MPa at 20% stance) are estimated that exceed their peaks in level walking by fourfold and twofold, respectively. Compared with level walking, ACL forces diminish in the first half of stance but substantially increase later in the second half (peak of 0.76 BW at 75% stance). Under nearly similar contact forces at 20% of stance, the contact stress on the tibiofemoral (TF) medial plateau reaches a peak (9.68 MPa) twice that on the PF joint suggesting the vulnerability of both joints. Compared with walking, stair ascent increases peak ACL force and both peak TF and PF contact stresses. Reductions in the knee flexion moment and/or angle appear as a viable strategy to mitigate internal loads and pain.

Radiological evaluation of patellofemoral instability and possible causes of assessment errors

Patellofemoral instability (PI) is the disruption of the patella’s relationship with the trochlear groove as a result of abnormal movement of the patella. To identify the presence of PI, conventional radiographs (anteroposterior, lateral, and axial or skyline views), magnetic resonance imaging, and computed tomography are used. In this study, we examined four main instability factors: Trochlear dysplasia, patella alta, tibial tuberosity–trochlear groove distance, and patellar tilt. We also briefly review some of the other assessment methods used in the quantitative and qualitative assessment of the patellofemoral joint, such as patellar size and shape, lateral trochlear inclination, trochlear depth, trochlear angle, and sulcus angle, in cases of PI. In addition, we reviewed the evaluation of coronal alignment, femoral anteversion, and tibial torsion. Possible causes of error that can be made when evaluating these factors are examined. PI is a multi-factorial problem. Many problems affecting bone structure and muscles morphologically and functionally can cause this condition. It is necessary to understand normal anatomy and biomechanics to make more accurate radiological measurements and to identify causes. Knowing the possible causes of measurement errors that may occur during radiological measurements and avoiding these pitfalls can provide a more reliable road map for treatment. This determines whether the disease will be treated medically and with rehabilitation or surgery without causing further complications.

Biomechanical Study of Patellar Component Fixation with Varying Degrees of Bone Loss

BACKGROUND

The decision as to whether or not to resurface the patella in revision total knee arthroplasty (TKA) is affected by the amount of patellar bone stock remaining; however, the impact of the cancellous bone status on patellar component fixation has not been studied. Therefore, we conducted a biomechanical study of patellar component fixation with varying degrees of cancellous bone loss.

METHODS

Sixty pairs of cadaveric patellae were randomly assigned between 3 groups and prepared in similar manner to a TKA with the standard 3-hole configuration. A control patella and an experimental patella were designated in each pair. To simulate bone loss in the experimental patellae, 1, 2, and 3 of the standard drill holes were uniformly enlarged to 12 mm in group 1, group 2, and group 3, respectively. Afterward, an all-polyethylene patellar component was cemented to each patella, as done intraoperatively. Patellar components were then sheared off using a materials testing system. The resulting mean offset yield force was analyzed within each group using paired t-tests.

RESULTS

The mean offset yield force for the control patellae was greater than the experimental patellae in group 1. In groups 2 and 3, the experimental patellae produced a greater mean offset yield force than the control patellae. Comparison within each group did not demonstrate a statistically significant difference.

CONCLUSION

Bone loss with enlargement of the patellar fixation holes, as is frequently seen in revision TKA, with holes up to 12 mm, does not significantly decrease patellar component fixation shear strength in this biomechanical cadaveric study.

Taping, Bracing, and Injection Treatment for Patellofemoral Pain and Patellar Tendinopathy

PURPOSE OF REVIEW

This article will focus on additional treatment options for the two most common causes of anterior knee pain, patellofemoral pain syndrome, and patellar tendinopathy. Conservative management is the first-line treatment for these conditions. For clinicians to maximize the efficacy of conservative treatment options for their patients, they must understand the most up-to-date literature evaluating the potential benefit of taping, bracing, and injections as adjunctive treatments for maximizing treatment success.

RECENT FINDINGS

Recent studies of bracing and taping have found them to be helpful for patients in the short-term management of pain and improving function. However, less is known about their exact mechanism but studies are encouraging that they have a subtle role in changing patellofemoral biomechanics. Injections remain a commonly used treatment for musculoskeletal conditions; however, the evidence for their use in patellofemoral pain and patellar tendinopathy is limited. The use of platelet-rich plasma (PRP), sclerosing, high volume, or stem cell injections is an exciting new area in the treatment of patellar tendinopathy. However, evidence at this time to recommend these treatments is lacking, and more well-designed studies are needed. The treatment of patellofemoral pain and patellar tendinopathy consists of a multi-faceted approach of physiotherapy and physical modalities. There is evidence for short-term use of taping and bracing for these conditions. The evidence for injections at this time is limited and remains under investigation. Future well-designed randomized controlled studies will provide insight into the efficacy of several different types of injections in the treatment of patellar tendinopathy. Physicians should feel comfortable integrating taping and bracing into their anterior knee pain treatment paradigm while making cautious use of invasive injections as adjunctive therapy.

Development and validation of a kinematically-driven discrete element model of the patellofemoral joint

Quantifying the complex loads at the patellofemoral joint (PFJ) is vital to understanding the development of PFJ pain and osteoarthritis. Discrete element analysis (DEA) is a computationally efficient method to estimate cartilage contact stresses with potential application at the PFJ to better understand PFJ mechanics. The current study validated a DEA modeling framework driven by PFJ kinematics to predict experimentally-measured PFJ contact stress distributions. Two cadaveric knee specimens underwent quadriceps muscle [215 N] and joint compression [350 N] forces at ten discrete knee positions representing PFJ positions during early gait while measured PFJ kinematics were used to drive specimen-specific DEA models. DEA-computed contact stress and area were compared to experimentally-measured data. There was good agreement between computed and measured mean and peak stress across the specimens and positions (r = 0.63-0.85). DEA-computed mean stress was within an average of 12% (range: 1-47%) of the experimentally-measured mean stress while DEA-computed peak stress was within an average of 22% (range: 1-40%). Stress magnitudes were within the ranges measured (0.17-1.26 MPa computationally vs 0.12-1.13 MPa experimentally). DEA-computed areas overestimated measured areas (average error = 60%; range: 4-117%) with magnitudes ranging from 139 to 307 mm² computationally vs 74-194 mm² experimentally. DEA estimates of the ratio of lateral to medial patellofemoral stress distribution predicted the experimental data well (mean error = 15%) with minimal measurement bias. These results indicate that kinematically-driven DEA models can provide good estimates of relative changes in PFJ contact stress.

In vivo comparison of medialized dome and anatomic patellofemoral geometries using subject-specific computational modeling

Successful outcome following total knee arthroplasty (TKA) with patella resurfacing is partly determined by the restoration of patellofemoral (PF) function and recovery of the quadriceps mechanism. The current study compared two patellar TKA geometries (medialized dome and anatomic) to determine their impact on PF mechanics and quadriceps function. In-vivo, subject-specific patellar mechanics were evaluated using a sequential experimental and modeling approach. First, stereo radiography, marker-based motion capture, and force plate data were collected for TKA patients (10 dome, 10 anatomic) performing a knee extension and lunge. Second, subject-specific, whole-body, musculoskeletal models, including 6 degrees-of-freedom (DOF) knee joint kinematics, were created for each subject and activity to predict quadriceps forces. Last, finite element models of each subject and activity were created to predict PF kinematics, patellar loading, moment arm, and patellar tendon angle. Differences in mechanics between dome and anatomic patients were highlighted during load-bearing (lunge) activity. Anatomic subjects demonstrated greater PF flexion angles (avg. 11 ± 3°) compared to dome subjects during lunge. Similar to the natural knee, contact locations on the patella migrated inferior to superior as the knee flexed in anatomic subjects, but remained relatively superior in dome subjects. Differences in kinematics and contact location likely contributed to altered mechanics with anatomic subjects presenting greater load transfer from the quadriceps to the patellar tendon in deep flexion (>75°), and dome subjects demonstrating larger contact forces during lunge. Although there was substantial patient variability, evaluations of PF mechanics suggested improved quadriceps function and more natural kinematics in the anatomic design. © 2018 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1910-1918, 2018.

Increased in vivo patellofemoral loading after total knee arthroplasty in resurfaced patellae

PURPOSE

The primary purpose of the study was to investigate if and how patellar bone tracer uptake (BTU) distribution in SPECT/CT is influenced by patellar resurfacing and the position of femoral and tibial TKA component position.

METHODS

A total of 104 knees of 103 consecutive patients who underwent primary TKA were prospectively investigated. Primary patellar resurfacing was done in 40 knees while 64 had a TKA without patellar resurfacing. All patients underwent clinical assessment using the knee society score (KSS) and standardized radiographs and Tc-99m-HDP-SPECT/CT before and 12 and 24 months after TKA. Measurements of BTU including intensity and anatomical distribution pattern in eight different patellar regions were performed. Tibial and femoral TKA component position was assessed from 3D reconstructed CT data. Patellar height, thickness and tilt were measured and the distance between the tibial tuberosity and the trochlear groove (TT-TG) was measured. Univariate analysis was performed to identify differences between the two groups (p < 0.05).

RESULTS

Significantly higher BTU was found in the anterior, non-articular, areas of the patella in patients who underwent patellar resurfacing (p < 0.05). The BTU pattern was similar between the groups, as the maximal uptake in both groups was seen in the superior posterior parts and the minimal uptake was seen in the inferior anterior parts. The mean postoperative KSS was significantly higher in the unresurfaced group after 12 months (p < 0.05), but with no significant difference after 24 months.

CONCLUSIONS

Based on the findings of the present study, patellar resurfacing is related to significantly higher BTU in the anterior parts of the patella and lower clinical outcomes. In light of these results, routine patellar resurfacing as part of a primary TKA might be reevaluated. SPECT/CT enables a precise localization of the BTU and might be considered as the ideal imaging modality for evaluation and investigate of patellofemoral disorders after TKA.

Quadriceps muscles activity during gait: comparison between PFPS subjects and healthy control

PURPOSE

The purpose of the study was to evaluate if during a common activity as walking, altered quadriceps muscular activity may be present in patellofemoral pain syndrome (PFPS) patients.

METHODS

Forty subjects with clinically diagnosed PFPS and forty healthy males matching in age, weight, height and level of sport activity were enrolled in the study. Subjects were asked to walk on an instrumented walking path at their self-selected speed. Force platform and motion tracking system were used for the analysis of the gait. Wireless surface EMG probes were used to evaluate quadriceps muscles activity. Rectus femoris, vastus medialis and lateralis activity percentage, onset and offset time, walking speed, cadence, step length, stride length, knee ROM during gait were measured and reported. Tegner activity questionnaire was reported.

RESULTS

Patient group showed a significant increasing in all quadriceps muscles activity when compared to the control (p < 0.05). In particular, for VM and VL muscle onset time was anticipated and offset time was postponed in PFPS group when compared with healthy group (p < 0.05). Knee range of motion during walking was significantly decreased in the patient group.

CONCLUSIONS

Young athletes with PFPS showed increased length of quadriceps muscles activity and reduced functional knee Rom while walking, comparing with healthy subjects, in particular muscular onset was anticipated in respect of the loading response event of the gait. Nonetheless, walking parameters were not affected by these alterations.

Role of Patellofemoral Offset in Total Knee Arthroplasty: A Randomized Trial

Total knee arthroplasty occasionally does not meet expectations. This randomized clinical trial assessed the effect of restoration of the native patellofemoral height on clinical outcomes. Group I underwent standard patellar bone resection; group II underwent modified patellar bone resection that adjusted the amount of anterior condylar bone removed and the anterior flange thickness. There were no differences in anterior knee pain, Western Ontario and McMaster Universities Arthritis Index scores, or Knee Injury and Osteoarthritis Outcome Score scores. Patellofemoral compartment height restoration versus patellar height alone does not appear to significantly reduce pain or improve function.

Comparison of Kinematics and Tibiofemoral Contact Pressures for Native and Transplanted Lateral Menisci

BACKGROUND

Lateral meniscus transplantation is a proven treatment option for the meniscus-deficient knee, yet little is known about meniscal kinematics, strain, and tibiofemoral contact pressure changes after transplantation or the effect of altered root position in lateral meniscus transplantation.

PURPOSE

To compare the native lateral meniscal kinematics, strain, and tibiofemoral contact pressures to a best-case scenario meniscus transplant with perfectly matched size and position and to determine how sensitive these factors are to subtle changes in shape and position by using a nonanatomic meniscus transplant position.

STUDY DESIGN

Controlled laboratory study.

METHODS

The lateral menisci of 8 cadaveric knees were circumferentially implanted with radiopaque spherical markers. They were mounted to a testing apparatus applying muscle and ground-reaction forces. The meniscus was evaluated at 0°, 30°, 90°, and 115° of knee flexion using Roentgen stereophotogrammetric analysis (RSA), with a pressure sensor affixed to the lateral tibial plateau. Measurements were recorded for 3 states: the native lateral meniscus, an anatomic autograft transplant, and a nonanatomic autograft transplant with an anteriorized posterior root position.

RESULTS

After transplantation, there was less posterior displacement in both the anatomic and nonanatomic transplant states compared with the native meniscus, but this was not significant. The largest lateral translation in the native state was 2.38 ± 1.58 mm at the anterolateral region from 0° to 90°, which was increased to 3.28 ± 1.39 mm (P = .25) and 3.12 ± 1.18 mm (P = .30) in the anatomic and nonanatomic transplant states, respectively. Internal deformations of the transplant states were more constrained, suggesting less compliance. The native meniscus distributed load over 223 mm², while both the anatomic (160 mm²) and nonanatomic (102 mm²) states concentrated pressure anteriorly to the tibial plateau centroid.

CONCLUSION

This study is the first to characterize kinematics in the native lateral meniscus compared with a transplanted state utilizing RSA. Results demonstrate increased meniscal constraint and pressure concentrations even after an ideal size and position matched transplantation, which further increased with a nonanatomic posterior root position.

CLINICAL RELEVANCE

The results show that kinematics are similar in both transplanted states when compared with the native meniscus at various flexion angles. Because both transplanted states were more constrained with less deformation compared with the native state, this should allow for relatively safe postoperative range of motion. However, in the transplanted states, peak pressures were distributed over a smaller area and shifted anteriorly. This pattern was exacerbated in the nonanatomic state compared with anatomic. This could have detrimental effects with regard to articular cartilage degeneration, and ultimately result in a failed transplantation.

Patella dislocations

The patellofemoral joint relies on muscular, ligamentous and bony support for normal stability and function. Dislocations commonly occur due to simultaneous rotational force with contraction of the quadriceps. Bony, muscular and ligamentous factors predispose to dislocations although no single factor causes more dislocations than any other. The diagnosis is based on the history combined with physical examination and radiological investigations. A careful scrutiny of the radiographs is necessary to determine the presence of osteochondral fractures in acute patellar dislocations. Special views and further imagining is indicated especially in those with recurrent symptoms. The treatment of acute dislocations is most commonly non operative. Surgery in acute patellar dislocations is indicated for intra articular fragments or those with large osteochondral fractures. Various soft tissue and bony realignment procedures have been described for recurrent dislocations. No single procedure is superior to another. Factors such as the patient’s age, functional needs, extent of malalignment and the condition of the joint are important factors to be considered prior to operative intervention. In this paper we discuss an overview of the diagnosis and management of patella dislocations with a literature review on the current concepts in treatment.

Importance of Patella, Quadriceps Forces, and Depthwise Cartilage Structure on Knee Joint Motion and Cartilage Response During Gait

In finite-element (FE) models of the knee joint, patella is often omitted. We investigated the importance of patella and quadriceps forces on the knee joint motion by creating an FE model of the subject's knee. In addition, depthwise strains and stresses in patellar cartilage with different tissue properties were determined. An FE model was created from subject's magnetic resonance images. Knee rotations, moments, and translational forces during gait were recorded in a motion laboratory and used as an input for the model. Three material models were implemented into the patellar cartilage: (1) homogeneous model, (2) inhomogeneous (arcadelike fibrils), and (3) random fibrils at the superficial zone, mimicking early stages of osteoarthritis (OA). Implementation of patella and quadriceps forces into the model substantially reduced the internal–external femoral rotations (versus without patella). The simulated rotations in the model with the patella matched the measured rotations at its best. In the inhomogeneous model, maximum principal stresses increased substantially in the middle zone of the cartilage. The early OA model showed increased compressive strains in the superficial and middle zones of the cartilage and decreased stresses and fibril strains especially in the middle zone. The results suggest that patella and quadriceps forces should be included in moment- and force-driven FE knee joint models. The results indicate that the middle zone has a major role in resisting shear forces in the patellar cartilage. Also, early degenerative changes in the collagen network substantially affect the cartilage depthwise response in the patella during walking.

Validation of predicted patellofemoral mechanics in a finite element model of the healthy and cruciate-deficient knee

Healthy patellofemoral (PF) joint mechanics are critical to optimal function of the knee joint. Patellar maltracking may lead to large joint reaction loads and high stresses on the articular cartilage, increasing the risk of cartilage wear and the onset of osteoarthritis. While the mechanical sources of PF joint dysfunction are not well understood, links have been established between PF tracking and abnormal kinematics of the tibiofemoral (TF) joint, specifically following cruciate ligament injury and repair. The objective of this study was to create a validated finite element (FE) representation of the PF joint in order to predict PF kinematics and quadriceps force across healthy and pathological specimens. Measurements from a series of dynamic in-vitro cadaveric experiments were used to develop finite element models of the knee for three specimens. Specimens were loaded under intact, ACL-resected and both ACL and PCL-resected conditions. Finite element models of each specimen were constructed and calibrated to the outputs of the intact knee condition, and subsequently used to predict PF kinematics, contact mechanics, quadriceps force, patellar tendon moment arm and patellar tendon angle of the cruciate resected conditions. Model results for the intact and cruciate resected trials successfully matched experimental kinematics (avg. RMSE 4.0°, 3.1mm) and peak quadriceps forces (avg. difference 5.6%). Cruciate resections demonstrated either increased patellar tendon loads or increased joint reaction forces. The current study advances the standard for evaluation of PF mechanics through direct validation of cruciate-resected conditions including specimen-specific representations of PF anatomy.

Sex differences in knee loading in recreational runners

Patellofemoral pain is the most common chronic pathology in recreational runners. Female runners are at greater risk of developing patellofemoral pain, although the exact mechanism behind this is not fully understood. This study aimed to determine whether female recreational runners exhibit distinct knee loading compared to males. Fifteen males and 15 females recreational runners underwent 3D running analysis at 4.0 ms(-1)±5%. Sagittal/coronal joint moments, patellofemoral contact forces (PTF) and pressures (PCP) were compared between sexes. The results show that females exhibited significantly greater knee extension (p<0.008, pη(2)=0.27: males=3.04; females=3.47 N m kg(-1)) and abduction (p<0.008, pη(2)=0.28: males=0.54; females=0.82 N m kg(-1)) moments as well as PTF (p<0.008, pη(2)=0.29: males=3.25; females=3.84 B.W.) and PCP (p<0.008, pη(2)=0.26: males=7.96; females=9.27 MPa) compared to males. Given the proposed relationship between knee joint loading and patellofemoral pathology, the current investigation provides insight into the incidence of patellofemoral pain in females.

Does high knee flexion cause separation of meniscal repairs?

BACKGROUND

Previous clinical studies comparing nonrestrictive and restrictive protocols after meniscal repair have shown no difference in outcomes; however, some surgeons still limit range of motion out of concern that it will place undue stress on the repair.

HYPOTHESIS

Large acute medial meniscal tears will gap during simulated open chain exercises at high flexion angles, and a repaired construct with vertical mattress sutures will not gap.

STUDY DESIGN

Controlled laboratory study.

METHODS

Tantalum beads were implanted in the medial menisci of 6 fresh-frozen cadaveric knees via an open posteromedial approach. Each knee underwent 10 simulated open chain flexion cycles with loading of the quadriceps and hamstrings. Testing was performed on 3 different states of the meniscus: intact, torn, and repaired. Biplanar radiographs were taken of the loaded knee in 90°, 110°, and 135° of flexion for each state. A 2.5-cm tear was created in the posteromedial meniscus and repaired with inside-out vertical mattress sutures. Displacement of pairs of beads spanning the tear was measured in all planes by use of radiostereometric analysis (RSA) with an accuracy of better than 80 μm.

RESULTS

With a longitudinal tear, compression rather than gapping occurred in all 3 regions of the posterior horn of the meniscus (mean ± standard deviation for medial collateral ligament [MCL], -321 ± 320 μm; midposterior, -487 ± 256 μm; root, -318 ± 150 μm) with knee flexion. After repair, meniscal displacement returned part way to intact values in both the MCL (+55 ± 250 μm) and root region (-170 ± 123 μm) but not the midposterior region, where further compression was seen (-661 ± 278 μm).

CONCLUSIONS

Acute posteromedial meniscal tears and repairs with vertical mattress sutures do not gap, but rather compress in the transverse plane at higher flexion angles when subjected to physiologic loads consistent with active, open kinetic chain range of motion rehabilitation exercises. The kinematics of the repaired meniscus more closely resemble that of the intact meniscus than that of the torn meniscus in regions adjacent to the MCL and the root but not in the midposterior region, where meniscal repair led to increased compression across the tear plane.

CLINICAL RELEVANCE

This study supports the idea that nonrestrictive unresisted open chain range of motion protocols do not place undue stress on meniscal repairs.

A biomechanical evaluation of hinged total knee replacement prostheses

The number of total knee replacements being performed worldwide is undergoing an unprecedented increase. Hinged total knee replacements, used in complex salvage and revision procedures, currently account for a small but growing proportion of prostheses implanted. Modern hinged prostheses share the same basic configuration, allowing flexion–extension and tibial rotation. One aspect on which designs differ is the anteroposterior location of the hinge. A more posterior hinge is designed to increase the patellar tendon moment arm, reducing the quadriceps force required for a given activity and benefiting the patient. Five commonly used total knee replacements were evaluated in terms of quadriceps force and patellar tendon moment arm using a laboratory-based rig. Significant differences were identified between the five prostheses in quadriceps force and patellar tendon moment arm. Analysis of the correlation between these two parameters indicates that while patellar tendon moment arm influences quadriceps force, it is not the only factor. Also important is the lever function of the patella, and it is suggested here that the non-physiological nature of the prosthetic patellofemoral geometry may result in unnatural joint function. Thus, a thorough understanding of the resulting kinematic function of hinged total knee replacements is becoming increasingly important in complex revision total knee replacement to meet rising patient expectations and functional demands.

Improved quadriceps' mechanical advantage in single radius TKRs is not due to an increased patellar tendon moment arm

Single femoral radius TKRs have been reported to improve quadriceps' mechanical advantage, leading to enhanced patient function. An increased patellar tendon moment arm (PTMA) has been cited as the main feature leading to improved quadriceps' mechanical advantage. However, these designs often incorporate a recessed trochlea which alters the patellar mechanism and may contribute to improved quadriceps' mechanical advantage. This study simultaneously measured the PTMA using two and three dimensional methods, as well as quadriceps forces (QF), patellofemoral kinematics and tibiofemoral kinematics in a motion analysis laboratory during an open chain leg extension activity. Six cadaveric knees were tested in the normal state and after implantation of three different single femoral radius TKR designs: cruciate retaining, posterior stabilised and rotating platform posterior stabilised (Stryker, Newbury, UK). QFs in the TKRs were between 15% and 20% lower than normal between 60° and 70° flexion. The increase in PTMA was insufficient to explain the reduced QF in the TKRs. The patellar flexion angle (PFA) of the TKRs was lower than normal at knee flexion angles greater than 50°, probably as a result of the recessed trochlea. A simple patellar model demonstrated that the reduced PFA may explain a large proportion of the reduction in QF after single radius TKR.

Assessment of a medial pivot total knee arthroplasty design in a cadaveric knee extension test model

A total knee has been designed to mimic less-compliant medial and more-compliant lateral behavior. In vivo testing compared open-kinematic chain behaviors of cadaver knees in their normal state and after implantation of the knee prosthesis. Specimen's limbs were computed tomography scanned, and infrared arrays on tibia and femur were registered to bone markers. Motion of the joint and quadriceps force were reported from 90° flexion to full extension. Less medial and more lateral anterior-posterior motion was seen in both the intact and the implanted knees. Tibiofemoral rotation and translation were similar in direction but were reduced in magnitude for the prosthetic knees. Quadriceps force, defined as that applied force required to extend the knee, required after implantation was variable between specimens but not statistically different from the intact condition. The prosthesis tested exhibits kinematic behavior similar to that in their normal state, with no difference in quadriceps force required for extension.

Reconstruction of medial patellofemoral ligament for chronic patellar instability

BACKGROUND

Disruption of the capsule, medial patellar retinaculum, and/or vastus medialis obliqus has been associated with recurrent patellar instability. Biomechanical studies have shown that the medial patellofemoral ligament (MPFL) is the main restraint against lateral patella displacement and reconstruction of the MPFL has become an accepted surgical technique to restore patellofemoral stability in patients having recurrent patellar dislocation. We report a prospective series of patients of chronic patellar instability treated by reconstruction of medial patellofemoral ligament.

MATERIALS AND METHODS

Twelve patients (15 knees) with recurrent dislocation of patella, were operated between January 2006 and December 2008. All patients had generalised ligament laxity with none had severe grade of patella alta or trochlear dysplasia. The MPFL was reconstructed with doubled semitendinosus tendon. Patients were followed up with subjective criteria, patellar inclination angle, and Kujala score.

RESULTS

The mean duration of followup after the operative procedures was an average of 42 months (range 24-60 months) 10 knees showed excellent results, 3 knees gave good results, and 2 knees had a fair result. The average patellar inclination angle decreased from 34.3° to 18.6°. The average preoperative Kujala functional score was 44.8 and the average postoperative score was 91.9.

CONCLUSION

MPFL reconstruction using the semitendinosus tendon gives good results in patients with chronic patellar instability without predisposing factors like severe patella alta and high-grade trochlear dysplasia, and for revision cases.

EFFECTS OF SIMULATED FIXED FEMORAL ROTATION ON THE PATELLOFEMORAL JOINT: IN VITRO AND IN VIVO BIOMECHANICAL ASSESSMENT IN CANINES

The quantitative effects of fixed femoral rotation on the patellofemoral joint were assessed in canines in vitro and in vivo. For the in vitro study, ten canine knees were examined in neutral and 30 degrees of internal and external fixed femoral rotations. Fuji film was inserted into the patellofemoral joint and quadriceps loading was simulated at 60 and 90 degrees of knee flexion. There was significant increase in patellofemoral contact pressures on the contralateral facets of the patella with 30 degrees of fixed femoral rotation at both knee flexion angles (p < 0.05). For the in vivo study, 12 skeletally mature mongrel dogs were subjected to either internal or external bilateral femoral rotational deformity of 30 degrees. Three animals served as controls. Biomechanical evaluation of the articular cartilage showed a statistically significant decrease for both the unrelaxed and relaxed apparent shear modulus at six months for both internal and external femoral rotations (p < 0.05) in comparison to the control. In vivo results from fixed femoral rotation on the patellofemoral joint correlate with that expected from in vitro biomechanical results. The results from this study suggest that rotational deformity of the femur should be corrected within six months to prevent patellofemoral joint arthrosis.

Effect of posterior tibial slope on knee biomechanics during functional activity

Treatment of medial compartment knee osteoarthritis with high tibial osteotomy can produce an unintended change in the slope of the tibial plateau in the sagittal plane. The effect of changing posterior tibial slope (PTS) on cruciate ligament forces has not been quantified for knee loading in activities of daily living. The purpose of this study was to determine how changes in PTS affect tibial shear force, anterior tibial translation (ATT), and knee-ligament loading during daily physical activity. We hypothesized that tibial shear force, ATT, and ACL force all increase as PTS increases. A previously validated computer model was used to calculate ATT, tibial shear force, and cruciate-ligament forces for the normal knee during three common load-bearing tasks: standing, squatting, and walking. The model calculations were repeated with PTS altered in 1° increments up to a maximum change in tibial slope of 10°. Tibial shear force and ATT increased as PTS was increased. For standing and walking, ACL force increased as tibial slope was increased; for squatting, PCL force decreased as tibial slope was increased. The effect of changing PTS on ACL force was greatest for walking. The true effect of changing tibial slope on knee-joint biomechanics may only be evident under physiologic loading conditions which include muscle forces.

The effect of load magnitude on three-dimensional patellar kinematics in vivo

Studies of three-dimensional patellar kinematics done with little or no applied load may not accurately reflect kinematics at physiological load levels, and may provide different results to those acquired with greater applied loads or in physiologic weightbearing. We report the effect of load magnitude on three-dimensional patellar kinematics (flexion, spin and tilt; proximal, lateral and anterior translation) using a validated, sequential static, MRI-based method. Ten healthy subjects loaded their study knee to 0% (no load), 15% and 30% bodyweight (BW) using a custom designed loading rig. Differences between loading levels were determined as a function of knee flexion for each kinematic parameter using linear hierarchical random-effects models. Quadratic and random slope terms were included in the models when significant. We found that the patellae flexed less with knee flexion at 30% BW load compared to 0% BW load (p<0.001) and 15% BW (p=0.004) load. The patellae showed a slight medial tilt with knee flexion at 30% BW load which was significantly less than the medial tilt seen at 0% BW load (p=0.017) and 15% BW load (p=0.043) with knee flexion. Small but statistically significant differences were also observed for proximal and anterior translation; the patellae were in a more proximal and posterior position at 30% BW load than at 0% BW load (p=0.010 and p=0.005, respectively) and 15% BW load (p<0.001 and p=0.029, respectively). Since differences in three-dimensional patellar kinematics were observed between loading levels, magnitudes of prescribed loads must be considered when designing studies and comparing results between studies.

Comparison of in vivo patellofemoral kinematics for subjects having high-flexion total knee arthroplasty implant with patients having normal knees

This study compares the in vivo patellar kinematics of high-flexion posterior cruciate ligament-retaining and posterior-stabilized total knee arthroplasty (TKA) implants with that of the healthy knee. Twenty-seven subjects performing weight-bearing deep knee bends were analyzed under fluoroscopic surveillance from full extension to maximum flexion. The patellofemoral contact positions and patellar flexion were similar for both TKAs. At low flexion, the patellofemoral contact was significantly more distal on the healthy patella than on the TKA patella, but in deeper flexion, there was no difference among the 3 groups. The tibiopatellar angle was similar for all 3 groups, except at deep flexion where the healthy patella rotated significantly more than the implanted ones. Patellofemoral separation was observed in some TKA knees, whereas it was absent in the healthy knees.

Multiplane Loading of the Extensor Mechanism Alters the Patellar Ligament Force/Quadriceps Force Ratio

Since the direction of the quadriceps force and location of the patellofemoral contact point likely differ between axial and multiplane loadings, the force and moment balance solutions for a multiplane loading condition may not yield the same patella ligament force/quadriceps force ratio (FPL/FQ ratio) when compared with an axial loading condition. The purpose of this study was to compare the effects of an axial loading condition and an anatomical, multiplane loading condition on the FPL/FQ ratio at various knee flexion angles. Ten cadaver knees were used in this investigation. Each was mounted on a custom jig that was fixed to an Instron frame. Quadriceps muscle loads were applied with same resultant force magnitudes under two force directions, as follows: (1) axial loading (central quadriceps tendon loading parallel to the femoral axis), and (2) an anatomically based, multiplane loading condition (individual vasti loaded, taking into consideration physiologic muscle fiber orientation). Patellar ligament tension was measured using a buckle transducer. The patellar ligament force/quadriceps force ratio (FPL/FQ ratio) was calculated for both loading conditions at 0 deg, 20 deg, 40 deg, and 60 deg of knee flexion. Across the range of knee motion evaluated, the FPL/FQ ratio for the axial loading condition was significantly greater than the FPL/FQ ratio for the multiplane loading condition. Our results suggest that loading orientation affects the transfer of forces from the quadriceps tendon to the patellar ligament.

Two-dimensional strain fields on the cross-section of the human patellofemoral joint under physiological loading

The objective of this study was to provide a detailed experimental assessment of the two-dimensional cartilage strain distribution on the cross-section of the human patellofemoral joint (PFJ) subjected to physiological load magnitudes and rates. The medial side of six human PFJs sectioned along their mid-sagittal plane was loaded up to the equivalent of two body weights on a whole joint, and strain measurements obtained from digital image correlation are reported at 0.5s. Normal strains tangential to the articular surface and shear strains in the plane of the cross-section showed consistent patterns among all specimens, whereas normal strains perpendicular to the articular surface exhibited some variability that may be attributed to subject-specific variations in material properties through the depth of the articular layers. Elevated tensile and compressive principal normal strains were observed near the articular surface, around the center of the contact region, with additional locations of elevated compressive strains occurring at the bone-cartilage interface. Under an average contact stress of approximately 3.3MPa, the peak compressive principal normal strains for the patella and femur averaged -0.158+/-0.072 and -0.118+/-0.051, respectively, magnitudes that are significantly greater than the relative changes in cartilage thickness, -0.090+/-0.030 and -0.072+/-0.038 (p<0.005). These experimental results provide a detailed description of the manner by which human PFJ articular layers deform in situ under physiological load conditions.

Effect of an UHMWPE patellar component on stress fields in the patella: a finite element analysis

An increased stress in the patella due to the implantation of a patellar button may also be another potential source of pain in total knee arthroplasty patients. This study assessed the location inside the patella having largest stress change after implantation of an ultra high molecular polyethylene patella button. Finite elements models of the patellae before and after implantation of patellar button were created. Experimentally determined spring constants of muscles and ligaments, and patellofemoral contacting loads were applied to the models at 30 degrees , 60 degrees , and 90 degrees of knee flexion. The Von Mises stress of the intact patella decreased with increased knee flexion, while that of implanted patella increased. Also, the stress range in the implanted patella was 3-9 times higher than in the intact one. The highly stressed region of the intact patella moved proximally with higher knee flexion angles, while that of the implanted model stayed near the central anterior patella. At 90 degrees of knee flexion, the stress in the anterodistal patella increased considerably after implantation of a patella button so that the anterodistal patella may be susceptible to be painful source after the total knee replacement.

The effect of an augmentation patella prosthesis versus patelloplasty on revision patellar kinematics and quadriceps tendon force: an ex vivo study

The purpose of this study was to assess the effect of 2 revision reconstructive interventions on patellofemoral joint mechanics in comparison to control. We flexed 8 cadaver knee specimens from 0 degrees to 60 degrees of flexion in a test rig designed to simulate weight-bearing flexion and extension (Oxford rig). Quadriceps tendon extensor force and patellar kinematics were recorded for control total knee arthroplasty (TKA) (normal primary TKA with patella resurfaced) and then for each of the 2 revision patellar interventions (after patelloplasty of typical revision knee patellar bone defect to leave a simple bony shell, and after TKA with augmentation patella resurfacing). Our results demonstrate that patellar kinematics and quadriceps extensor force are optimized when the patella is reconstructed to normal anteroposterior thickness.

Patellofemoral joint forces

In this review of patellofemoral joint forces as they might apply to implant design, methodologies for estimating forces on the patella and estimates of the forces, as reported in the literature, are summarized. Two methodologies exist for studying joint loads; one that measures kinematics in-vivo and uses analysis to estimate the joint loads and another that measures ground reaction forces and uses analysis to estimate the joint loads. In both these analyses many assumptions are required with varying degrees of uncertainty; here, those assumptions are examined with data from the published literature. The topics covered include: relationships between quadriceps forces and patellofemoral forces or patella ligament forces, relationships between knee joint moments and quadriceps forces, knee joint moments in various gaits, relationships between patellofemoral forces and lateral subluxation forces, and relationships between patella forces and inferior-superior forces. In many cases, there is little data on patella forces during normal activities, in other cases, there are some discrepancies in reported patella forces, i.e. during squat.

The effect of quadriceps contraction during weight-bearing on four patellar height indices

The effect of weight-bearing on the height of the patellar using four radiological indices was studied in 25 healthy men using lateral radiographs of the knee in 30° of flexion non-weight-bearing and weight-bearing. The position of the patella was quantified using the Insall-Salvati, the modified Insall-Salvati, the Blackburne-Peel and the Caton indices. The contraction of the quadriceps on weight-bearing resulted in statistically significant proximal displacement of the patella with all four indices studied. The mean Insall-Salvati index was 0.919 (sd 0.063) before and 1.109 (sd 0.042) after weight-bearing (p = 0.001), while the mean modified Insall-Salvati index was 0.734 (sd 0.039) before and 0.896 (sd 0.029) after weight-bearing (p = 0.041). Similarly, the Blackburne-Peel index was 0.691 (sd 0.09) before and 0.807 (sd 0.137) after weight-bearing (p = 0.012). The mean Caton index was 0.861 (sd 0.09) before and 0.976 (sd 0.144) after weight-bearing (p = 0.023).

The effect of quadriceps contraction should be considered in clinical studies where the patellar position indices are reported.

The management of recurrent patellar dislocation

Acute and chronic trauma, chronic abnormal joint loading conditions, and hemarthroses have been implicated in the development of degenerative joint disease. Patellar instability with acute and recurrent patellar dislocation provides all of these ingredients. This article describes an approach to the treatment of recurrent patellar instability that considers the unique features and expectations of the patient rather than using a generic algorithm.

Analysis of the gliding pattern of the canine flexor digitorum profundus tendon through the A2 pulley

Friction between a tendon and its pulley was first quantified using the concept of the arc of contact. Studies of human tendons conformed closely to a theoretical nylon cable/nylon rod model. However, we observed differences in measured friction that depended on the direction of motion in the canine model. We hypothesized that fibrocartilaginous nodules in the tendon affected the measurements and attempted to develop a theoretical model to explain the observations we made. Two force transducers were connected to each end of the canine flexor digitorum profundus tendon and the forces were recorded when it was moved through the A2 pulley toward a direction of flexion by an actuator and then reversed a direction toward extension. The changes of a force as a function of tendon excursion were evaluated in 20 canine paws. A bead cable/rod model was developed to simulate the canine tendon-pulley complex. To interpret the results, a free-body diagram was developed. The two prominent fibrocartilaginous nodules in the tendon were found to be responsible for deviation from a theoretical nylon cable gliding around the rod model, in a fashion analogous to the effect of the patella on the quadriceps mechanism. A bead cable/rod model qualitatively reproduced the findings observed in the canine tendon-pulley complex. Frictional coefficient of the canine flexor tendon-pulley was 0.016+/-0.005. After accounting for the effect created by the geometry of two fibrocartilaginous nodules within the tendon, calculation of frictional force in the canine tendon was possible.

Computational biomechanics of knee joint in open kinetic chain extension exercises

Open kinetic chain (OKC) extension exercises are commonly performed to strengthen quadriceps muscles and restore joint function in performance enhancement programs, in exercise therapies and following joint reconstruction. Using a validated 3D nonlinear finite element model, the detailed biomechanics of the entire joint in OKC extension exercises are investigated at 0, 30, 60 and 90 degrees joint angles. Two loading cases are simulated; one with only the weight of the leg and the foot while the second considers also a moderate resistant force of 30 N acting at the ankle perpendicular to the tibia. The presence of the 30 N markedly influences the results both in terms of the magnitude and the trend. The resistant load substantially increases the required quadriceps, patellar tendon, cruciate ligaments and joint contact forces, especially at near 90 degrees angles with the exception of ACL force that is increased at 0 degrees angle. At post-ACL reconstruction period or in the joint with ACL injury, the exercise should preferably be avoided at near full extension positions under large resistant forces.

Rehabilitation and Nonoperative Treatment of Patellar Instability

Patellofemoral instability can be a difficult condition for clinicians to manage. Differentiation needs to be made as to whether the problem is an acute injury where a traumatic incident has usually precipitated the dislocation or whether the problem is a recurrent instability where the patellofemoral joint is unstable during everyday activities. This review defines instability, discusses the factors affecting instability, and provides assessment procedures and nonoperative intervention strategies for the clinician.

Effect of patellar taping on vasti onset timing, knee kinematics, and kinetics in asymptomatic individuals with a delayed onset of vastus medialis oblique

This randomized within-subject study investigated the effects of patellar tape on the onset of electromyographic (EMG) activity of vastus medialis obliquus (VMO) relative to vastus lateralis (VL), knee kinematics, and kinetics in 12 currently asymptomatic individuals with a VMO timing deficit and a history of patellofemoral pain. Participants were required to complete stair stepping and normal-pace and fast-pace walking tasks under three experimental conditions; no tape, control tape and therapeutic tape. EMG onsets of VMO and VL were measured by surface electrodes, stance phase knee flexion by the PEAK movement analysis system and vertical ground reaction force by a force plate. A two-way repeated measures analysis of variance showed that neither therapeutic tape nor control tape had any effect on the EMG VMO-VL onset timing difference. Therapeutic tape, but not control tape, led to significant increases in stance phase knee flexion. The first peak vertical ground reaction force was lowered by both control and therapeutic tape but only during fast walking. The results suggest that tape induced effects on neuromotor control of the vasti seen in other studies are related to reductions in pain rather than the presence of a baseline timing deficit. However, this cannot explain the improvements in stance phase knee flexion observed with tape.

Biomechanics of changes in ACL and PCL material properties or prestrains in flexion under muscle force-implications in ligament reconstruction

The effects of changes in cruciate ligament material and prestrain on knee joint biomechanics following ligament reconstruction surgery by a tendon are not adequately known. A 3D nonlinear finite element model of the entire knee joint was used to investigate the joint response at different flexion angles under a quadriceps force while varying ACL and PCL initial strains or material properties. The ACL and PCL forces as well as tibiofemoral contact forces/areas substantially increased with greater ACL or PCL initial strains or stiffness. The patellofemoral contact force slightly increased whereas the tibial extensor moment slightly decreased with tenser or stiffer ACL. Reverse trends were predicted with slacker ACL. Results confirm the hypotheses that changes in the prestrain of one cruciate ligament substantially influence the force in the other cruciate ligament and the entire joint and that the use of the patellar tendon (PT) as a replacement for cruciate ligaments markedly alters the joint biomechanics with trends similar to those predicted when increasing prestrains. Forces in both ACL and PCL ligaments increased as one of them became tenser or stiffer and diminished as it became slacker. These results have important consequences in joint biomechanics following ligament injuries or replacement and tend to recommend the use of grafts with smaller prestrains (i.e. slacker than intact) when using the PT as the replacement material with stiffness greater than that of replaced ligament itself.

Reliability of a technique for determining sagittal knee geometry from lateral knee radiographs

The purposes of this study were to describe an analytical technique for determining selected 2-dimensional geometric characteristics of a knee joint using lateral knee radiographs and to examine the inter- and intra-analyst reliability of this technique. Five lateral knee radiographs of different knee flexion angles (25-85 degrees at intervals of 15 degrees ) were obtained from five subjects. Two graduate and five undergraduate students with knowledge of knee anatomy served as the analysts and were asked to identify certain landmarks from the radiographs. The coordinates of these landmarks were used to determine the effective moment arm of the quadriceps force, patellar tendon length, patella height, patellar mechanism and patellar tendon angles, and tibiofemoral and patellofemoral joint spaces. For each radiograph, intraclass correlation coefficients (ICCs) were computed for combinations of 2-7 analysts. Using all seven analysts, the ICCs ranged from 0.9967 to 0.9985 for different radiographs. When fewer analysts were used, the average ICCs were 0.9975 (6 analysts), 0.9974 (5 analysts), 0.9974 (4 analysts), 0.9974 (3 analysts), and 0.9973 (2 analysts). Four of the analysts re-analyzed the radiographs 2-3months after the initial analyses. Intra-analyst ICCs ranged from 0.9842 to 0.9999. Overall, the high ICC values indicate excellent inter- and intra-analyst reliability. The proposed technique is reliable and may be used for both clinical and research purposes. The relatively small reductions in ICCs when fewer analysts were used suggest that a single experienced analyst is sufficient for clinical assessment. However, 2-3 analysts are recommended for research purposes.

Biomechanics of the knee joint in flexion under various quadriceps forces

Bioemchanics of the entire knee joint including tibiofemoral and patellofemoral joints were investigated at different flexion angles (0 degrees to 90 degrees ) and quadriceps forces (3, 137, and 411 N). In particular, the effect of changes in location and magnitude of restraining force that counterbalances the isometric extensor moment on predictions was investigated. The model consisted of three bony structures and their articular cartilage layers, menisci, principal ligaments, patellar tendon, and quadriceps muscle. Quadriceps forces significantly increased the anterior cruciate ligament, patellar tendon, and contact forces/areas as well as the joint resistant moment. Joint flexion, however, substantially diminished them all with the exception of the patellofemoral contact force/area that markedly increased in flexion. When resisting extensor moment by a force applied on the tibia, the force in cruciate ligaments and tibial translation significantly altered as a function of magnitude and location of the restraining force. Quadriceps activation generated large ACL forces at full extension suggesting that post ACL reconstruction exercises should avoid large quadriceps exertions at near full extension angles. In isometric extension exercises against a force on the tibia, larger restraining force and its more proximal location to the joint substantially decreased forces in the anterior cruciate ligament at small flexion angles whereas they significantly increased forces in the posterior cruciate ligament at larger flexion angles.

Effect of patellar tendon shortening on tracking of the patella

BACKGROUND

Although 10% postoperative patellar tendon shortening after bone-patellar tendon-bone autograft reconstruction of the anterior cruciate ligament has been reported, there are no published studies assessing the effect of shortening on patellofemoral joint biomechanics under physiological loading conditions.

PURPOSE

To investigate the influence of patellar tendon shortening on patellofemoral joint biomechanics.

STUDY DESIGN

Controlled laboratory study.

METHODS

The authors evaluated the patellofemoral contact area, the location of contact, and the patellofemoral joint reaction force and contact stresses in 7 cadaveric knees before and after 10% patellar tendon shortening. Shortening was achieved using a specially designed device. Experimental conditions simulating those occurring during level walking were employed: physiological quadriceps loads and corresponding angles of tibial rotation were applied at 15 degrees , 30 degrees , and 60 degrees flexion of the knee. Patellofemoral joint contact areas were measured before and after shortening using the silicone oil-carbon black powder suspension squeeze technique.

RESULTS

After patellar tendon shortening, patellofemoral joint contact areas were displaced proximally on the patellar surface and distally on the femoral surface. Although the contact area increased by 18% at 15 degrees of knee flexion (P = .04), no significant change occurred at 30 degrees or 60 degrees of knee flexion (P > .05). Patellofemoral contact stress remained unchanged after patellar tendon shortening (P > .05) at each flexion angle.

CONCLUSION

Our results suggest that a 10% shortening of the patellar tendon does not alter patellar contact stresses during locomotion. It is not clear whether apparent changes in contact location in all positions and contact area at 15 degrees would have clinical consequences.

Dynamic evaluation of contact pressure and the effects of graft harvest with subsequent lateral release at osteochondral donor sites in the knee

PURPOSE

To dynamically evaluate contact pressure about the periphery of the lateral femoral condyle in intact knees, to qualify the effects of osteochondral donor graft harvest on this contact pressure, and to quantify the effects of lateral release on contact pressure after graft harvest.

TYPE OF STUDY

Cadaveric analysis.

METHODS

Digital electronic pressure-sensing cells were used to measure contact pressure over the periphery of the lateral femoral condyle in 10 fresh-frozen knee specimens. Nonweightbearing resistive extension was simulated as the knees were placed through a functional range of motion. Dynamic pressure readings were evaluated over intact cartilage, around the rims of four 5-mm osteochondral defects, and after lateral release.

RESULTS

The pressure cells were all subjected to contact pressures as the knees were placed through a functional range of motion. Average maximal contact pressure progressed distally as the knees were flexed. The creation of 5-mm osteochondral defects did not lead to a significant increase in rim stress concentration over the surrounding cartilage. Lateral release resulted in small decreases in contact pressure over the osteochondral defects.

CONCLUSIONS

The creation of 5-mm donor defects about the lateral aspect of the lateral femoral condyle does not lead to significant alterations in local contact pressure.

CLINICAL RELEVANCE

Our biomechanical findings may have important implications relating to cartilage restoration using osteochondral autografting procedures. Donor-site morbidity may be minimized if donor-site defects are limited to 5 mm and smaller.