Dynamic stress response of the implant/cement interface: an axisymmetric analysis of a knee tibial component

A Circumferentially Flanged Tibial Tray Minimizes Bone-Tray Shear Micromotion

Aseptic loosening of the tibial component is the major complication of total knee arthroplasty. There is an association between early excessive shear micromotion between the bone and the tray of the tibial component and late aseptic loosening. Using non-linear finite element analysis, whether a tibial tray with a circumferentially flanged rim and a mating cut in the proximal tibia could minimize bone-tray shear micromotion was considered. fifteen competing tray designs with various degrees of flange curvature were assessed with the aim of minimizing bone-tray shear micromotion. A trade-off was found between reducing micromotion and increasing peripheral cancellous bone stresses. It was found that, within the limitations of the study, there was a theoretical design that could virtually eliminate micromotion due to axial loads, with minimal bone removal and without the use of screws or pegs.

Long stemmed total knee arthroplasty with interlocking screws: a computational bone adaptation study

The ability of an interlocking screw fixation technique to minimize bone loss related to stress shielding in the tibia was investigated and compared to the abilities of cement and press-fit fixation. Full bony ingrowth has been associated with greater stress shielding than partial ingrowth; therefore, the effect of intimate bonding of the stem to bone on subsequent bone loss was also studied. A damage- and disuse-based remodeling theory was coupled with a two-dimensional finite element model of the tibia to predict changes in bone remodeling following long stemmed total knee arthroplasty (TKA) for four different fixation techniques (cement, press-fit, interlock with bony ingrowth, and interlock without bony ingrowth). Remodeling changes commenced with the model state variables--bone area fraction, mechanical stimulus, damage, and remodeling activity--at steady-state values predicted by the intact tibia simulation. After TKA and irrespective of fixation technique, the model predicted elevated remodeling due to disuse, in which more bone was removed than replenished. In regions below the tibial tray and along the cortices, the interlocking stem with full bony ingrowth and the cemented stem caused the least amount of bone loss. An interlocking stem with a smooth, matted finish did not reduce the bone loss associated with interlocking fixation.

Finite Element Analysis of Tibial Implants - Effect of Fixation Design and Friction Model

A three dimensional nonlinear finite element model was developed to investigate tibial fixation designs and friction models (Coulomb's vs nonlinear) in total knee arthroplasty in the immediate postoperative period with no biological attachment. Bi-directional measurement-based nonlinear friction constitutive equations were used for the bone-porous coated implant interface. Friction properties between the polyethylene and femoral components were measured for this study. Linear elastic isotropic but heterogeneous mechanical properties taken from literature were considered for the bone. The Tensile behaviour of polyethylene was measured and subsequently modeled by an elasto-plastic model. Based on the earlier finite element and experimental pull-out studies, pegs and screws were also realistically modeled. The geometry of every component was obtained through measurement. The PCA tibial baseplate with three different configurations was considered; one with three screws, one with one screw and two short inclined porous-coated pegs, and a third one with no fixation for the sake of comparison. The axial load of 2000N was applied through the femoral component on the medial plateau of articular insert. It was found that Coulomb's friction significantly underestimates the relative micromotion at the bone-implant interface. The lowest micromotion and lift-off were found for the design with screws. Relative micromotion and stress transfer at the bone-implant interface depended significantly on the friction model and on the baseplate anchorage configuration. Cortical and cancellous bones carried, respectively, 10-13% and 65-86% of the axial load depending on the fixation configuration used. The remaining portion was transmitted as shear force by screws and pegs. Normal and Mises stresses as well as contact area in the polyethylene insert were nearly independent of the baseplate fixation design. The Maximum Mises stress in the polyethylene exceeded yield and was found 1-2 mm below the contact surface for all designs.

The bone-cement interface: histological observations on the interface of cemented arthroplasties within the immediate and late phases

Undecalcified specimens of cemented arthroplasties obtained during the early and late phases were studied. On the tenth postoperative day, there was excellent interlocking of the cement with the soft and hard tissues of the bone: there was no necrosis of the bed of the implant: a neutrophilic and macrophagic inflammatory response, where present, was mild and focal. Samples of the bone-cement interface of well fixed components obtained (at autopsy or by biopsy) many years after implantation revealed a thin and quiescent fibrous interfacial membrane alternating with bone and osteoid (that is, segmental osseointegration) or a cartilaginous layer abutting on the cement. It is concluded that, firstly, modern cementation techniques are not associated with extensive necrosis of the underlying bone in the immediate postoperative period; secondly, monomeric and polymeric methylmethacrylate as such is not toxic to the tissues; and, thirdly, acrylic cement is osseointegrated when motion at the interface is at its minimum.