1
|
Nourishirazi R, Moradkhani G, SharafatVaziri A, Nematy H, Shayan-Moghadam R, Karimpour M. Biomechanical study of using patient-specific diaphyseal femoral cone in revision total knee arthroplasty (rTKA). J Orthop 2024; 57:65-71. [PMID: 38983674 PMCID: PMC11228766 DOI: 10.1016/j.jor.2024.06.002] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 04/21/2024] [Accepted: 06/01/2024] [Indexed: 07/11/2024] Open
Abstract
Background The primary objective of revision total knee surgery is to achieve solid bone fixation. Generally, this could be accomplished using sleeves and long stems, which require substantial remaining bone stock and may increase the risk of stem tip pain. An alternative approach involves the use of customized diaphyseal cones, which can preserve the integrity of the bone canal. This study evaluates the impact of employing femoral diaphyseal cones with various stem lengths on stress distribution and relative motion. Methods CT scan data from five patients were used to generate the 3D model of the femur, cement, customized stems, and cones, along with assigning patient-specific material for each candidate's femur. Three different stem lengths, both with and without the customized cone, were assessed under three gait loading conditions to compare the resulting Von Mises stress distribution and relative motion. Results Analysis indicated that the use of customized femoral cones moderately increases stress distribution values up to 30 % while significantly reducing relative motion at the femoral canal-cone interface by nearly 60 %. The presence of the cone did not significantly alter relative motion with varying stem lengths, although stem length variation without a cone substantially affected these values. Conclusion Incorporating cones alongside stems enhances metaphyseal fixation, reduces stress shielding, potentially allowing for the use of shorter stems. Furthermore, cones promote osseointegration by minimizing relative motion, ultimately improving prosthetic stability.
Collapse
Affiliation(s)
- Reza Nourishirazi
- School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran
| | - Ghazaleh Moradkhani
- School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran
| | - Arash SharafatVaziri
- Center for Orthopedic Trans-Disciplinary Applied Research (COTAR), Tehran University of Medical Sciences, Tehran, Iran
| | - Hamidreza Nematy
- School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran
| | - Ramin Shayan-Moghadam
- Center for Orthopedic Trans-Disciplinary Applied Research (COTAR), Tehran University of Medical Sciences, Tehran, Iran
| | - Morad Karimpour
- School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran
| |
Collapse
|
2
|
Wan Q, Zhang A, Liu Y, Chen H, Zhao X, Han Q, Wang J. Stem to prevent periprosthetic fracture after notching in total knee arthroplasty. INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN BIOMEDICAL ENGINEERING 2024:e3842. [PMID: 39099381 DOI: 10.1002/cnm.3842] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 12/01/2023] [Revised: 05/09/2024] [Accepted: 06/18/2024] [Indexed: 08/06/2024]
Abstract
Improper osteotomy during total knee arthroplasty (TKA) can lead to anterior femoral notching, which increases the risk of periprosthetic fractures due to stress concentration. One potential solution is the addition of an intramedullary stem to the femoral component. However, the optimal stem length remains unclear. In this study, we aimed to determine the optimal stem length using finite element models. Finite element models of femurs were developed with unstemmed prostheses and prostheses with stem lengths of 50, 75, and 100 mm. Under squat loading conditions, the von Mises stress at the notch and stress distribution on four transversal sections of the femur were analyzed. Additionally, micromotion of the prosthesis-bone interface was evaluated to assess initial stability. The unstemmed prosthesis exhibited a von Mises stress of 191.8 MPa at the notch, which decreased to 43.1, 8.8, and 23.5 MPa for stem lengths of 50, 75, and 100 mm, respectively. The stress reduction on four selected femoral transversal sections compared with the unstemmed prosthesis was 40.0%, 84.4%, and 67.1% for stem lengths of 50, 75, and 100 mm, respectively. Micromotion analysis showed a maximum of 118.8 μm for the unstemmed prosthesis, which decreased significantly with the application of stems, particularly at the anterior flange. Intramedullary stems effectively reduced stress concentration at the femoral notch. The 50-mm stem length provided the optimal combination of reduced notch stress, minimized stress-shielding effect, and decreased micromotion at the anterior flange.
Collapse
Affiliation(s)
- Qian Wan
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| | - Aobo Zhang
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| | - Yang Liu
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| | - Hao Chen
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| | - Xue Zhao
- Department of Endocrinology and Metabolism, The First Hospital of Jilin University, Changchun, China
| | - Qing Han
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| | - Jincheng Wang
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun, China
| |
Collapse
|
3
|
Innocenti B. Are Flexible Metaphyseal Femoral Cones Stable and Effective? A Biomechanical Study on Hinged Total Knee Arthroplasty. J Arthroplasty 2024; 39:1328-1334. [PMID: 37952738 DOI: 10.1016/j.arth.2023.11.009] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 07/03/2023] [Revised: 11/07/2023] [Accepted: 11/07/2023] [Indexed: 11/14/2023] Open
Abstract
BACKGROUND Cones currently available in the market are rigid, and unless they are custom-specific designed, are unable to correctly adapt to the shape of the patient's bone. Therefore, flexible metaphyseal cones have been recently introduced to reduce potential bone trauma during implantation. Even if a preliminary clinical study on their use has shown promising results, no biomechanical study evaluates and quantifies their mechanical efficacy and safety. METHODS Two commercial versions of flexible cones were analyzed in this study using finite element analysis, based on a previously validated model. Each cone geometry was modeled both as flexible and as rigid, and implanted following surgical guidelines. Three activities were simulated in this study and compared among configurations: surgical impaction, walking, and chair rise. RESULTS During impaction, results showed considerably reduced stress in the flexible cones in comparison with rigid ones; the stress resulted was also better distributed and more homogeneous all over the cortical bone, with lower bone peaks. Considering the 2 different activities, the analysis did not show any remarkable differences between flexible and rigid cones both in terms of bone stress and implant micromotion. CONCLUSIONS The findings demonstrate that metaphyseal flexible cones allow macrodeformation during impaction due to their flexibility, and therefore, are safer in comparison with rigid cones. However, for the daily tasks investigated, results showed no major differences between rigid and flexible cones in terms of bone stress, implant stability, and micromotion. Therefore, their mechanical performances can be considered similar to the rigid cone.
Collapse
Affiliation(s)
- Bernardo Innocenti
- BEAMS Department (Bio Electro and Mechanical Systems), Université Libre de Bruxelles, Brussels, Belgium
| |
Collapse
|
4
|
Quevedo Gonzalez FJ, Lipman JD, Sculco PK, Sculco TP, De Martino I, Wright TM. An Anterior Spike Decreases Bone-Implant Micromotion in Cementless Tibial Baseplates for Total Knee Arthroplasty: A Biomechanical Study. J Arthroplasty 2024; 39:1323-1327. [PMID: 38000515 DOI: 10.1016/j.arth.2023.11.020] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 06/14/2023] [Revised: 11/15/2023] [Accepted: 11/17/2023] [Indexed: 11/26/2023] Open
Abstract
BACKGROUND Cementless tibial baseplates in total knee arthroplasty include fixation features (eg, pegs, spikes, and keels) to ensure sufficient primary bone-implant stability. While the design of these features plays a fundamental role in biologic fixation, the effectiveness of anterior spikes in reducing bone-implant micromotion remains unclear. Therefore, we asked: Can an anterior spike reduce the bone-implant micromotion of cementless tibial implants? METHODS We performed computational finite element analyses on 13 tibiae using the computed tomography scans of patients scheduled for primary total knee arthroplasty. The tibiae were virtually implanted with a cementless tibial baseplate with 2 designs of fixation of the baseplate: 2 pegs and 2 pegs with an anterior spike. We compared the bone-implant micromotion under the most demanding loads from stair ascent between both designs. RESULTS Both fixation designs had peak micromotion at the anterior-lateral edge of the baseplate. The design with 2 pegs and an anterior spike had up to 15% lower peak micromotion and up to 14% more baseplate area with micromotions below the most conservative threshold for ingrowth, 20 μm, than the design with only 2 pegs. The greatest benefit of adding an anterior spike occurred for subjects who had the smallest area of tibial bone below the 20 μm threshold (ie, most at risk for failure to achieve bone ingrowth). CONCLUSIONS An anteriorly placed spike for cementless tibial baseplates with 2 pegs can help decrease the bone-implant micromotion during stair ascent, especially for subjects with increased bone-implant micromotion and risk for bone ingrowth failure.
Collapse
Affiliation(s)
| | - Joseph D Lipman
- Department of Biomechanics, Hospital for Special Surgery, New York
| | - Peter K Sculco
- Adult Reconstruction and Joint Replacement Service, Hospital for Special Surgery, New York
| | - Thomas P Sculco
- Adult Reconstruction and Joint Replacement Service, Hospital for Special Surgery, New York
| | - Ivan De Martino
- Department of Geriatric Science and Orthopaedics, Università Cattolica del Sacro Cuore, Rome, Italy
| | - Timothy M Wright
- Department of Biomechanics, Hospital for Special Surgery, New York
| |
Collapse
|
5
|
Gersie T, Bitter T, Wolfson D, Freeman R, Verdonschot N, Janssen D. Quantification of long-term nonlinear stress relaxation of bovine trabecular bone. J Mech Behav Biomed Mater 2024; 152:106434. [PMID: 38350383 DOI: 10.1016/j.jmbbm.2024.106434] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/09/2023] [Revised: 01/11/2024] [Accepted: 01/25/2024] [Indexed: 02/15/2024]
Abstract
The reliability of computational models in orthopedic biomechanics depends often on the accuracy of the bone material properties. It is widely recognized that the mechanical response of trabecular bone is time-dependent, yet it is often ignored for the sake of simplicity. Previous investigations into the viscoelastic properties of trabecular bone have not explored the relationship between nonlinear stress relaxation and bone mineral density. The inclusion of this behavior could enhance the accuracy of simulations of orthopedic interventions, such as of primary fixation of implants. Although methods to quantify the viscoelastic behavior are known, the time period during which the viscoelastic properties should be investigated to obtain reliable predictions is currently unclear. Therefore, this study aimed to: 1) Investigate the duration of stress relaxation in bovine trabecular bone; 2) construct a material model that describes the nonlinear viscoelastic behavior of uniaxial stress relaxation experiments on trabecular bone; and 3) implement bone density into this model. Uniaxial compressive stress relaxation experiments were performed with cylindrical bovine femoral trabecular bone samples (n = 16) with constant strain held for 24 h. Additionally, multiple stress relaxation experiments with four ascending strain levels with a holding time of 30 min, based on the results of the 24-h experiment, were executed on 18 bovine bone cores. The bone specimens used in this study had a mean diameter of 12.80 mm and a mean height of 28.70 mm. A Schapery and a Superposition model were used to capture the nonlinear stress relaxation behavior in terms of applied strain level and bone mineral density. While most stress relaxation happened in the first 10 min (up to 53 %) after initial compression, the stress relaxation continued even after 24 h. Up to 69 % of stress relaxation was observed at 24 h. Extrapolating the results of 30 min of experimental data to 24 h provided a good fit for accuracy with much improved experimental efficiency. The Schapery and Superposition model were both capable of fitting the repeated stress relaxation in a sample-by-sample approach. However, since bone mineral density did not influence the time-dependent behavior, only the Superposition model could be used for a group-based model fit. Although the sample-by-sample approach was more accurate for an individual specimen, the group based approach is considered a useful model for general application.
Collapse
Affiliation(s)
- Thomas Gersie
- Radboudumc, Orthopaedic Research Lab, PO Box 9101, 6500 HB, Nijmegen, Netherlands.
| | - Thom Bitter
- Radboudumc, Orthopaedic Research Lab, PO Box 9101, 6500 HB, Nijmegen, Netherlands
| | - David Wolfson
- DePuy Synthes Joint Reconstruction, WW Research & Development, LS11 OBG, Leeds, UK
| | - Robert Freeman
- DePuy Synthes Joint Reconstruction, WW Research & Development, LS11 OBG, Leeds, UK
| | - Nico Verdonschot
- Radboudumc, Orthopaedic Research Lab, PO Box 9101, 6500 HB, Nijmegen, Netherlands; University of Twente, Faculty of Science and Technology, 7522LW, Enschede, Netherlands
| | - Dennis Janssen
- Radboudumc, Orthopaedic Research Lab, PO Box 9101, 6500 HB, Nijmegen, Netherlands
| |
Collapse
|
6
|
Wearne LS, Rapagna S, Awadalla M, Keene G, Taylor M, Perilli E. Quantifying the immediate post-implantation strain field of cadaveric tibiae implanted with cementless tibial trays: A time-elapsed micro-CT and digital volume correlation analysis during stair descent. J Mech Behav Biomed Mater 2024; 151:106347. [PMID: 38181568 DOI: 10.1016/j.jmbbm.2023.106347] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/11/2023] [Revised: 12/18/2023] [Accepted: 12/22/2023] [Indexed: 01/07/2024]
Abstract
Primary stability, the mechanical fixation between implant and bone prior to osseointegration, is crucial for the long-term success of cementless tibial trays. However, little is known about the mechanical interplay between the implant and bone internally, as experimental studies quantifying internal strain are limited. This study employed digital volume correlation (DVC) to quantify the immediate post-implantation strain field of five cadaveric tibiae implanted with a commercially available cementless titanium tibial tray (Attune, DePuy Synthes). The tibiae were subjected to a five-step loading sequence (0-2.5 bodyweight, BW) replicating stair descent, with concomitant time-elapsed micro-CT imaging. With progressive loads, increased compression of trabecular bone was quantified, with the highest strains directly under the posterior region of the tibial tray implant, dissipating with increasing distance from the bone-implant interface. After load removal of the last load step (2.5BW), residual strains were observed in all of the five tibiae, with residual strains confined within 3.14 mm from the bone-implant interface. The residual strain is reflective of the observed initial migration of cementless tibial trays reported in clinical studies. The presence of strains above the yield strain of bone accepted in literature suggests that inelastic properties should be included within finite element models of the initial mechanical environment. This study provides a means to experimentally quantify the internal strain distribution of human tibia with cementless trays, increasing the understanding of the mechanical interaction between bone and implant.
Collapse
Affiliation(s)
- Lauren S Wearne
- Medical Device Research Institute, College of Science and Engineering, Flinders University, Adelaide, South Australia, Australia
| | - Sophie Rapagna
- Medical Device Research Institute, College of Science and Engineering, Flinders University, Adelaide, South Australia, Australia; Flinders Microscopy and Microanalysis, College of Science and Engineering, Flinders University, Adelaide, South Australia, Australia
| | - Maged Awadalla
- Medical Device Research Institute, College of Science and Engineering, Flinders University, Adelaide, South Australia, Australia
| | - Greg Keene
- Orthopaedic Department, SportsMed, Adelaide, South Australia, Australia
| | - Mark Taylor
- Medical Device Research Institute, College of Science and Engineering, Flinders University, Adelaide, South Australia, Australia
| | - Egon Perilli
- Medical Device Research Institute, College of Science and Engineering, Flinders University, Adelaide, South Australia, Australia.
| |
Collapse
|
7
|
Glenday JD, Vigdorchik JM, Sculco PK, Kahlenberg CA, Mayman DJ, Debbi EM, Lipman JD, Wright TM, González FJQ. A novel computational workflow to holistically assess total knee arthroplasty biomechanics identifies subject-specific effects of joint mechanics on implant fixation. J Biomech 2024; 164:111973. [PMID: 38325192 DOI: 10.1016/j.jbiomech.2024.111973] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/24/2023] [Revised: 12/04/2023] [Accepted: 01/29/2024] [Indexed: 02/09/2024]
Abstract
Computational studies of total knee arthroplasty (TKA) often focus on either joint mechanics (kinematics and forces) or implant fixation mechanics. However, such disconnect between joint and fixation mechanics hinders our understanding of overall TKA biomechanical function by preventing identification of key relationships between these two levels of TKA mechanics. We developed a computational workflow to holistically assess TKA biomechanics by integrating musculoskeletal and finite element (FE) models. For our initial study using the workflow, we investigated how tibiofemoral contact mechanics affected the risk of failure due to debonding at the implant-cement interface using the four available subjects from the Grand Challenge Competitions to Predict In Vivo Knee Loads. We used a musculoskeletal model with a 12 degrees-of-freedom knee joint to simulate the stance phase of gait for each subject. The computed tibiofemoral joint forces at each node in contact were direct inputs to FE simulations of the same subjects. We found that the peak risk of failure did not coincide with the peak joint forces or the extreme tibiofemoral contact positions. Moreover, despite the consistency of joint forces across subjects, we observed important variability in the profile of the risk of failure during gait. Thus, by a combined evaluation of the joint and implant fixation mechanics of TKA, we could identify subject-specific effects of joint kinematics and forces on implant fixation that would otherwise have gone unnoticed. We intend to apply our workflow to evaluate the impact of implant alignment and design on TKA biomechanics.
Collapse
Affiliation(s)
- Jonathan D Glenday
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, NY, USA
| | | | - Peter K Sculco
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, NY, USA
| | | | - David J Mayman
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, NY, USA
| | - Eytan M Debbi
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, NY, USA
| | - Joseph D Lipman
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, NY, USA
| | - Timothy M Wright
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, NY, USA
| | | |
Collapse
|
8
|
Sánchez E, de Vries E, Matthews D, van der Heide E, Janssen D. The effect of coating characteristics on implant-bone interface mechanics. J Biomech 2024; 163:111949. [PMID: 38281459 DOI: 10.1016/j.jbiomech.2024.111949] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/21/2023] [Revised: 12/04/2023] [Accepted: 01/10/2024] [Indexed: 01/30/2024]
Abstract
Successful osseointegration of press-fit implants depends on the initial stability, often measured by the micromotions between the implant and bone. A good primary stability can be achieved by optimizing the compressive and frictional forces acting at the bone-implant interface. The frictional properties of the implant-bone interface, which depend on the roughness and porosity of the implant surface coating, can affect the primary stability. Several reversible (elastic) and non-reversible (permanent) deformation processes take place during frictional loading of the implant-bone interface. In case of a rough coating, the asperities of the implant surface are compressed into the bone leading to mechanical interlocking. To optimize fixation of orthopaedic implants it is crucial to understand these complex interactions between coating and bone. The objective of the current study was to gain more insight into the reversible and non-reversible processes acting at the implant-bone interface. Tribological experiments were performed with two types of porous coatings against human cadaveric bone. The results indicated that the coefficient of friction depended on the coating roughness (0.86, 0.95, and 0.45 for an Ra roughness of 41.2, 53.0, and a polished surface, respectively). Larger elastic and permanent displacements were found for the rougher coating, resulting in a lower interface stiffness. The experiments furthermore revealed that relative displacements of up to 35 µm can occur without sliding at the interface. These findings have implications for micromotion thresholds that currently are assumed for osseointegration, and suggest that bone ingrowth actually occurs in the absence of relative sliding at the implant-bone interface.
Collapse
Affiliation(s)
- Esther Sánchez
- Radboud University Medical Center, Radboud Institute for Health Sciences, Orthopaedic Research Lab, Nijmegen, the Netherlands
| | - Erik de Vries
- University of Twente, Faculty of Engineering Technology, Laboratory for Surface Technology and Tribology, Enschede, the Netherlands
| | - David Matthews
- University of Twente, Faculty of Engineering Technology, Laboratory for Surface Technology and Tribology, Enschede, the Netherlands; Feng Chia University, Department of Materials Science & Engineering, Taiwan
| | - Emile van der Heide
- University of Twente, Faculty of Engineering Technology, Laboratory for Surface Technology and Tribology, Enschede, the Netherlands
| | - Dennis Janssen
- Radboud University Medical Center, Radboud Institute for Health Sciences, Orthopaedic Research Lab, Nijmegen, the Netherlands.
| |
Collapse
|
9
|
Corbaz J, Barimani B, Vauclair F. Early aseptic loosening of a press-fit radial head prosthesis - A case series of 6 patients. J Int Med Res 2023; 51:3000605221135881. [PMID: 37082909 PMCID: PMC10126620 DOI: 10.1177/03000605221135881] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 04/22/2023] Open
Abstract
OBJECTIVE Radial head arthroplasty (RHA) is the principal treatment option for comminuted radial head (RH) fractures. Here, we present six cases of failed RHA using a modular monopolar press-fit RHA that was subsequently withdrawn from the market because it was associated with a high incidence of loosening. METHODS We retrospectively collected data from six patients who had received Radial Head Prothesis SystemTM at our centre between July 2015 and June 2016. The average follow-up was 40 months. RESULTS Aseptic loosening of the stem affected five (83%) of the six RHA. Four of these were symptomatic and RHA removal was performed. For these patients, the pain subsided and their elbow range of motion (ROM) improved. CONCLUSION While the ideal design for an RHA is still debatable, RHA is an efficient treatment option that restores elbow stability and function after a comminuted RH fracture. Importantly, removal of the prosthesis is an effective remedy following RHA associated elbow pain and decreased ROM.
Collapse
Affiliation(s)
- J Corbaz
- Centre Hospitalier Universitaire Vaudois, 1011 Lausanne, Switzerland
| | - B Barimani
- Department of Orthopaedic Surgery, McGill University, Montreal, Quebec, Canada
| | - F Vauclair
- Bone and Motion Center - Hirslanden, 1006 Lausanne, Switzerland
| |
Collapse
|
10
|
Wan Q, Zhang A, Liu Y, Chen H, Zhang J, Xue H, Han Q, Wang J. The influence of body weight index on initial stability of uncemented femoral knee protheses: A finite element study. Heliyon 2023; 9:e13819. [PMID: 36895366 PMCID: PMC9988490 DOI: 10.1016/j.heliyon.2023.e13819] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/30/2022] [Revised: 02/07/2023] [Accepted: 02/13/2023] [Indexed: 02/19/2023] Open
Abstract
Background and objective Obesity is one of the risk factors for osteoarthritis. The end-stage treatment for osteoarthritis is total knee arthroplasty (TKA). However, it remains controversial whether a high body mass index (BMI) affects the initial stability of the femoral prosthesis after TKA. Finite element analysis (FEA) was used to investigate this question in this study. Methods Four femur models that assembled with TKA femoral components were reconstructed and divided into high BMI group and normal BMI group. The three-dimensional femurs were modeled and assigned inhomogeneous materials based on computed tomography (CT) images. Then each FEA model was applied with gait and deep bend loading conditions to evaluate the maximum principal strain on the distal femur and the relative micromotion between the femur and prosthesis. Results The mean strain of the high BMI group increased by 32.7% (936.9 με versus 706.1 με) and 50.9% (2064.5 με versus 1368.2 με) under gait and deep bend loading conditions, respectively, compared to the normal BMI group. Meanwhile, the mean micromotion of the high BMI group increased by 41.6% (2.77 μm versus 1.96 μm) and 58.5% (62.1 μm versus 39.2 μm), respectively. Under gait condition, the maximum micromotion for high BMI group was 33.8 μm and would compromise the initial stability. Under deep bend condition, the maximum strain and micromotion exceeded -7300 με and 28 μm for both groups. Conclusion High BMI caused higher strain on the bone and higher micromotion between the prosthesis and the femur. Gait activities could be risky for prosthesis stability in high BMI group while be safe in normal group. Deep bend activities were highly dangerous for both groups with high BMI and normal BMI and should be avoided.
Collapse
Affiliation(s)
- Qian Wan
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun 130000, China
| | - Aobo Zhang
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun 130000, China
| | - Yang Liu
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun 130000, China
| | - Hao Chen
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun 130000, China
| | - Jiangbo Zhang
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun 130000, China
| | - Haowen Xue
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun 130000, China
| | - Qing Han
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun 130000, China
| | - Jincheng Wang
- Department of Orthopedics, The Second Hospital of Jilin University, Changchun 130000, China
| |
Collapse
|
11
|
Fallahnezhad K, O'Rourke D, Bahl JS, Thewlis D, Taylor M. The role of muscle forces and gait cycle discretization when assessing acetabular cup primary stability: A finite element study. COMPUTER METHODS AND PROGRAMS IN BIOMEDICINE 2023; 230:107351. [PMID: 36709556 DOI: 10.1016/j.cmpb.2023.107351] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/27/2022] [Revised: 12/18/2022] [Accepted: 01/10/2023] [Indexed: 06/18/2023]
Abstract
UNLABELLED The aim of this study was to investigate the influence of the muscle force contribution and loading cycle discretization on the predicted micromotion and interfacial bone strains in the implanted acetabulum. To this end, a patient specific finite element model of the hemipelvis was developed, based on the CT-scan and gait analysis results, collected as part of the authors' previous work. Outcomes of this study suggests that the acetabular cup micromotion and interfacial bone strains can be predicted just using the joint contact force. This helps to reduce the complexity of the finite element models by ignoring the contribution of muscle forces and the associated challenges of mapping these forces to the pelvis. However, the gait cycle needs to be adequately discretised to capture the micromotion at the bone-implant interface. BACKGROUND AND OBJECTIVE The Dalstra load case, which includes muscle forces, has been widely adopted in the literature for studying the mechanical environment in the intact and implanted acetabulum. To simplify the modelling approach, some researchers ignore the contribution of muscle forces. The Dalstra load case is also divided into eight separate load steps (five in the stance phase and three in the swing phase), however, it is unclear whether this adequately captures the micromotions, for a cementless acetabular cup, during a simulated activity. The aim of this study was to investigate the influence of the muscle force contribution and loading cycle discretization on the predicted micromotion and interfacial bone strains. METHODS In this work, a patient specific finite element model of the hemipelvis was developed, based on the CT-scan and gait analysis results, collected as part of the authors' previous work. Finite element simulations were performed using the joint contact and muscle forces derived from two sources. The first approach was used the load case proposed by Dalstra et al. The second approach used joint contact and muscle forces predicted by a musculoskeletal model. Additionally, the musculoskeletal load case was discretised into 50 equal load steps and the results compared with the equivalent Dalstra load steps. RESULTS The results showed that the contribution of the muscle forces resulted in minor differences in both the magnitude and distribution of the predicted acetabular micromotion (up to 4.01% in the mean acetabular micromotion) and interfacial bone strains (up to 10.34% in the mean interfacial bone strains). The degree of gait cycle discretisation had a significant influence on the acetabular micromotion with a difference of 20.89% in the mean acetabular micromotion. CONCLUSION Outcomes of this study suggests that the acetabular cup micromotion and interfacial bone strains can be predicted just using the joint contact force. This helps to reduce the complexity of the finite element models by ignoring the contribution of muscle forces and the associated challenges of mapping these forces to the pelvis. However, the gait cycle needs to be adequately discretised to capture the micromotion at the bone-implant interface.
Collapse
Affiliation(s)
- Khosro Fallahnezhad
- Medical Device Research Institute, College of Science and Engineering, Flinders University, 1284 South Road, Clovelly Park, South Australia 5042, Australia.
| | - Dermot O'Rourke
- School of Mechanical, Medical and Process Engineering, Queensland University of Technology, Gardens Point campus, 2 George St, Brisbane, Brisbane, QLD 4000, Australia
| | - Jasvir S Bahl
- Centre for Orthopaedics and Trauma Research (COTR), The University of Adelaide, 4 North Terrace, Adelaide SA 5000, Australia
| | - Dominic Thewlis
- Centre for Orthopaedics and Trauma Research (COTR), The University of Adelaide, 4 North Terrace, Adelaide SA 5000, Australia
| | - Mark Taylor
- Medical Device Research Institute, College of Science and Engineering, Flinders University, 1284 South Road, Clovelly Park, South Australia 5042, Australia
| |
Collapse
|
12
|
Yang H, Bayoglu R, Clary CW, Rullkoetter PJ. Impact of patient, surgical, and implant design factors on predicted tray-bone interface micromotions in cementless total knee arthroplasty. J Orthop Res 2023; 41:115-129. [PMID: 35437819 DOI: 10.1002/jor.25344] [Citation(s) in RCA: 2] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 11/01/2021] [Revised: 03/14/2022] [Accepted: 04/16/2022] [Indexed: 02/04/2023]
Abstract
Micromotion magnitudes exceeding 150 µm may prevent bone formation and limit fixation after cementless total knee arthroplasty (TKA). Many factors influence the tray-bone interface micromotion but the critical parameters and sensitivities are less clear. In this study, we assessed the impacts of surgical (tray alignment, tibial coverage, and resection surface preparation), patient (bone properties and tibiofemoral kinematics), and implant design (tray feature and surface friction) factors on tray-bone interface micromotions during a series of activities of daily living. Micromotion was estimated via three previously validated implant-bone finite element models and tested under gait, deep knee bending, and stair descent loads. Overall, the average micromotion across the tray-bone cementless contact interface ranged from 9.3 to 111.4 µm, and peak micromotion was consistently found along the anterior tray edge. Maximizing tibial coverage above a properly sized tibial tray (an average of 12.3% additional area) had minimal impact on micromotion. A 1 mm anterior tray alignment change reduced the average micromotion by an average of 16.1%. Two-degree tibial angular resection errors reduced the area for bone ingrowth up to 48.1%. Differences on average micromotion from ±25% changes in bone moduli were up to 75.5%. A more posterior tibiofemoral contact due to additional 100 N posterior force resulted in an average of 79.3% increase on average micromotion. Overall, careful surgical technique, patient selection, and controlling kinematics through articular design all contribute meaningfully to minimizing micromotion in cementless TKA, with centralizing the load transfer to minimize the resulting moment at the anterior tray perimeter a consistent theme.
Collapse
Affiliation(s)
- Huizhou Yang
- Center for Orthopaedic Biomechanics, University of Denver, Denver, Colorado, USA
| | - Riza Bayoglu
- Center for Orthopaedic Biomechanics, University of Denver, Denver, Colorado, USA
| | - Chadd W Clary
- Center for Orthopaedic Biomechanics, University of Denver, Denver, Colorado, USA
| | - Paul J Rullkoetter
- Center for Orthopaedic Biomechanics, University of Denver, Denver, Colorado, USA
| |
Collapse
|
13
|
Yang H, Behnam Y, Clary C, Rullkoetter PJ. Drivers of initial stability in cementless TKA: Isolating effects of tibiofemoral conformity and fixation features. J Mech Behav Biomed Mater 2022; 136:105507. [PMID: 36209592 DOI: 10.1016/j.jmbbm.2022.105507] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/21/2022] [Revised: 09/18/2022] [Accepted: 10/01/2022] [Indexed: 11/06/2022]
Abstract
The initial fixation of cementless tibial trays after total knee arthroplasty is critical to ensure bony ingrowth and long-term fixation. Various fixed-bearing implant designs that utilize different fixation features, surface coatings, and bony preparations to facilitate this initial stability are currently used clinically. However, the role of tibiofemoral conformity and the effect of different tray fixation features on initial stability are still unclear. This study assessed the implant stability of two TKA designs during a series of simulated daily activities including experimental testing and corresponding computational models. Tray-bone interface micromotions and the porous area ideal for bone ingrowth were investigated computationally and compared between the two designs. The isolated effect of femoral-insert conformity and fixation features on the micromotion was examined separately by virtually exchanging design features. The peak interface micromotions predicted were at least 47% different for the two designs, which was a combined result of different femoral-insert conformity (contributed 79% of the micromotion difference) and fixation features (21%). A more posterior femoral-insert contact due to lower tibiofemoral conformity in a force-controlled simulation significantly increased the micromotion and reduced the surface area ideal for bone ingrowth. The maximum difference in peak micromotions caused by only changing the fixation features was up to 33%. Overall, the moment arm from the insert articular contact point to the anterolateral tray perimeter was the primary factor correlated to peak and average micromotion. Our results indicated that tray-bone micromotion could be minimized by centralizing the load transfer and optimizing the fixation features.
Collapse
Affiliation(s)
- Huizhou Yang
- Center for Orthopaedic Biomechanics, University of Denver, Denver, CO, 80208, USA.
| | - Yashar Behnam
- Center for Orthopaedic Biomechanics, University of Denver, Denver, CO, 80208, USA
| | - Chadd Clary
- Center for Orthopaedic Biomechanics, University of Denver, Denver, CO, 80208, USA
| | - Paul J Rullkoetter
- Center for Orthopaedic Biomechanics, University of Denver, Denver, CO, 80208, USA.
| |
Collapse
|
14
|
Mikashima Y, Imamura H, Shirakawa Y, Yano K, Ikari K, Okazaki K. Modern cementless posterior stabilized mobile-bearing total knee arthroplasty shows comparable clinical and radiographical results to its cemented predecessor at 1-year follow-up. Knee Surg Sports Traumatol Arthrosc 2022; 30:3131-3137. [PMID: 35781580 DOI: 10.1007/s00167-022-07047-7] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 03/02/2022] [Accepted: 06/04/2022] [Indexed: 10/17/2022]
Abstract
PURPOSE The purpose of this study was to evaluate perioperative and short-term clinical and radiographical results of a modern PS mobile-bearing cementless TKA system. METHODS A retrospective review of a consecutive series of TKAs was performed by a single surgeon using a cementless or cemented TKA of the same design (Attune, DePuy Synthes, Massachusetts, USA). The 2011 Knee Society Score, Forgotten Joint Score-12, Hip-Knee-Ankle angle, and the presence of radiolucent lines (RLLs) were reviewed 1-year postoperatively with 1:1 matching performed for age, gender, body mass index, and preoperative UCLA score. Fisher's exact test or independent Student's t-test were used for statistical analyses. RESULTS Forty-five cementless and 45 cemented TKAs were reviewed after 1:1 matching. The mean operative time was 8.8 min shorter (P < .01), and the mean amount of drainage was 40.0 ml greater (P = .04) in the cementless cohort. At 1-year postoperatively, there were no significant differences in both cohorts in 2011 Knee Scores and Forgotten Joint Scores-12, with no patients requiring revision surgery (NS). The incidence of RLLs was significantly higher in cementless TKAs (51%) than that in cemented TKAs (22%, P < .01). However, the mean width of RLLs in the cementless TKAs (0.2 mm) was significantly smaller (P < .01) than that in the cemented TKAs (0.8 mm) at 1-year postoperatively with no progression. CONCLUSION A recently introduced cementless PS mobile-bearing TKA design demonstrated comparable postoperative and radiographical results to its cemented predecessor at 1-year follow-up. LEVEL OF EVIDENCE Retrospective cohort study, Level III.
Collapse
Affiliation(s)
- Yoshinori Mikashima
- Oume Knee Surgery Center, Takagi Hospital, Imadera 5-18-19, Oume City, Tokyo, Japan.
| | - Hitoshi Imamura
- Oume Knee Surgery Center, Takagi Hospital, Imadera 5-18-19, Oume City, Tokyo, Japan
| | - Yoshiko Shirakawa
- Oume Knee Surgery Center, Takagi Hospital, Imadera 5-18-19, Oume City, Tokyo, Japan
| | - Koichiro Yano
- Department of Orthopaedics, Tokyo Women's Medical University, Tokyo, Japan
| | - Katsunori Ikari
- Department of Orthopaedics, Tokyo Women's Medical University, Tokyo, Japan
| | - Ken Okazaki
- Department of Orthopaedics, Tokyo Women's Medical University, Tokyo, Japan
| |
Collapse
|
15
|
Micro-CT scan optimisation for mechanical loading of tibia with titanium tibial tray: A digital volume correlation zero strain error analysis. J Mech Behav Biomed Mater 2022; 134:105336. [PMID: 35863298 DOI: 10.1016/j.jmbbm.2022.105336] [Citation(s) in RCA: 5] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/28/2022] [Revised: 06/08/2022] [Accepted: 06/24/2022] [Indexed: 01/08/2023]
Abstract
Primary stability of press-fit tibial trays is achieved by introducing an interference fit between bone and implant. The internal cancellous bone strains induced during this process and during loading have yet to be quantified experimentally. Advancements in large-gantry micro-CT imaging and digital volume correlation (DVC) allow quantification of such strains. However, before undertaking such a test, experimental requirements and DVC performance need to be examined, particularly considering the presence of a large orthopaedic implant (tibial tray). The aim of this study was to assess the DVC zero-strain accuracy (mean absolute error: MAER) and precision (standard deviation of error: SDER) on a cadaveric human tibia implanted with a titanium press-fit tray across four plausible scanning configurations, using a cabinet micro-CT system (Nikon XT H 225 ST). These varied in rotation step and resulting scanning time (106 min vs. 66 min), presence or absence of a 2 mm-thick aluminium cylinder for mechanical testing, and X-ray tube voltage (150 kVp vs. 215 kVp). One proximal tibia was implanted and micro-CT scanned (42 μm/pixel), with repeated scanning and specimen repositioning in between. DVC (DaVis, LaVision, direct correlation) was performed on nine cubic volumes of interest (VOIs: 13.4 mm-side) and across the entire proximal tibia. Strain errors were comparable across the four scanning configurations and sufficiently low for assessing bone within its elastic region in VOIs (MAER=223-540 με; SDER=88-261 με) and at organ level (MAER=536 με; SDER=473 με). Whilst the investigated experimental conditions, including a large titanium implant, present added complexity for DVC analysis, scans of sufficient quality can be achieved, reaching a compromise between the DVC requirements and the wanted application. The approach used for choosing the X-ray source settings considering the transmitted X-ray signal intensity and source power, is also discussed.
Collapse
|
16
|
Glenday JD, Wright TM, Lipman JD, Sculco PK, Mayman DJ, Vigdorchik JM, Quevedo-Gonzalez FJ. Effect of varus alignment on the bone-implant interaction of a cementless tibial baseplate during gait. J Orthop Res 2022; 40:816-825. [PMID: 34231249 DOI: 10.1002/jor.25129] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 10/13/2020] [Revised: 02/01/2021] [Accepted: 06/09/2021] [Indexed: 02/04/2023]
Abstract
Component alignment in total knee arthroplasty is a determining factor for implant longevity. Mechanical alignment, which provides balanced load transfer, is the most common alignment strategy. However, a retrospective review found that varus alignment, which could lead to unbalanced loading, can happen in up to 18% of tibial baseplates. This may be particularly burdensome for cementless tibial baseplates, which require low bone-implant micromotion and avoidance of bone overload to obtain bone ingrowth. Our aim was to assess the effect of varus alignment on the bone-implant interaction of cementless baseplates. We virtually implanted 11 patients with knee OA with a modern cementless tibial baseplate in mechanical alignment and in 2° of tibial varus alignment. We performed finite element simulations throughout gait, with loading conditions derived from literature. Throughout the stance phase, varus alignment had greater micromotion and percentage of bone volume at risk of failure than mechanical alignment. At mid-stance, when the most critical conditions occurred, the average increase in peak micromotion and amount of bone at risk of failure due to varus alignment were 79% and 59%, respectively. Varus alignment also resulted in the decrease of the surface area with micromotion compatible with bone ingrowth. However, for both alignments, this surface area was larger than the average area of ingrowth reported for well-fixed implants retrieved post-mortem. Our findings suggest that small varus deviations from mechanical alignment can adversely impact the biomechanics of the bone-implant interaction for cementless tibial baseplates during gait; however, the clinical implications of such changes remain unclear.
Collapse
|
17
|
van Otten TJM, van Loon CJM. Early aseptic loosening of the tibial component at the cement-implant interface in total knee arthroplasty: a narrative overview of potentially associated factors. Acta Orthop Belg 2022; 88:103-111. [PMID: 35512160 DOI: 10.52628/88.1.13] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/20/2022]
Abstract
Total knee arthroplasty (TKA) is a highly effective surgical procedure, but in some patients TKAs fail early due to a variety of underlying factors. About 11% of revision TKAs within one year of primary TKA are the result of aseptic loosening of the tibial component at the cement-implant interface. Literature regarding the most important factors associated with this type of loosening is scarce. The objective is to give an overview of the literature regarding factors associated with aseptic loosening of the tibia component at the cement-implant interface in total knee arthroplasty. A narrative literature review based on publications identified through PubMed and CINAHL databases. Twelve studies were identified, which describe a total of 299 cases of early aseptic loosening of the tibia component at the cement-implant interface. The main associated factors reported were cementa- tion factors. These factors included the use of high viscosity cement (HVC), cement application methods and cement thickness. Other main reported associated factor related to implant design factors, which included component shape and surface roughness. The least frequently reported associated factors related to the patient characteristics of body mass index (BMI). Several factors associated with early aseptic loosening of the tibial component at the cement-implant interface in total knee arthroplasty were identified in this review. The most frequently reported associated factors related to cementation factors and implant design factors. Because the literature in this area is scarce, further research is warranted in an effort to prevent early aseptic loosening in future TKAs.
Collapse
|
18
|
Awadalla M, Solomon LB, Heldreth M, Rullkoetter P, Taylor M. Assessment of the primary stability of revision tibial trays augmented with a cementless sleeve in AORI Type III defects. Knee 2021; 33:150-158. [PMID: 34624749 DOI: 10.1016/j.knee.2021.09.005] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 11/04/2020] [Revised: 08/31/2021] [Accepted: 09/12/2021] [Indexed: 02/02/2023]
Abstract
BACKGROUND Previous studies have evaluated the initial stability of uncemented tibial components in revision total knee replacement (rTKR) in the presence of an Anderson Orthopaedic Research Institute (AORI) Type II tibial defect. This study sought to evaluate similar metrics in the severe Type III (AORI TIII) defects with combined uncemented stem and sleeve fixation, specifically, the effect of varying the stem's length and tibial canal engagement upon stability and bone strain. METHOD Finite element models generated from the CT scans of 4 tibias with Type III defects were used to investigate the primary stability, in terms of the bone-implant composite peak micromotion (CPM) and microstrains (CPS), achieved after virtual implantations with and without stems. RESULTS A stemless rTKR had increased metaphyseal CPM and CPS compared to all stemmed implants. Significant area of the bone supporting the stemless rTKR had CPS greater than bone yield (7000 με). Short engaging stems (≤150 mm construct length), could not achieve reliable engagement in the diaphysis (canal fill ≤ 50%), leading to insufficient reduction of CPS (≥5000 με). Longer engaging stems (170-220 mm construct length), were able to reliably engage the diaphysis (fill ratio ≥ 75%) resulting in CPS ≤ 5000 με. Although, non-engaging stems resulted in increased CPM and CPS compared to engaging stems, long non-engaging stems (170-220 mm construct) appeared to provide additional stability to the rTKR compared to stemless rTKR. CONCLUSION The results indicate a likely correlation between uncemented stem engagement and metaphyseal CPS in Type III defects. Excessive strain within the supporting metaphyseal bone is likely to lead to rTKR migration and loosening.
Collapse
Affiliation(s)
- Maged Awadalla
- Medical Device Research Institute, College of Science and Engineering, Flinders University, SA, Australia.
| | - Lucian B Solomon
- Centre of Orthopaedic and Trauma Research, University of Adelaide, SA, Australia; Centre for Orthopaedic and Trauma Research, Australia
| | - Mark Heldreth
- DePuy Synthes Inc, Joint Reconstruction, Warsaw, IN, USA
| | - Paul Rullkoetter
- Department of Mechanical and Materials Engineering, University of Denver, CO, USA
| | - Mark Taylor
- Medical Device Research Institute, College of Science and Engineering, Flinders University, SA, Australia
| |
Collapse
|
19
|
Quevedo González FJ, Meyers KN, Schraut N, Mehrotra KG, Lipman JD, Wright TM, Ast MP. Do Metaphyseal Cones and Stems Provide Any Biomechanical Advantage for Moderate Contained Tibial Defects in Revision TKA? A Finite-Element Analysis Based on a Cadaver Model. Clin Orthop Relat Res 2021; 479:2534-2546. [PMID: 34351312 PMCID: PMC8509913 DOI: 10.1097/corr.0000000000001912] [Citation(s) in RCA: 12] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 03/01/2021] [Accepted: 07/06/2021] [Indexed: 01/31/2023]
Abstract
BACKGROUND Satisfactory management of bone defects is important to achieve an adequate reconstruction in revision TKA. Metaphyseal cones to address such defects in the proximal tibia are increasingly being used; however, the biomechanical superiority of cones over traditional techniques like fully cementing the implant into the defect has not yet been demonstrated. Moreover, although long stems are often used to bypass the defects, the biomechanical efficacy of long stems compared with short, cemented stems when combined with metaphyseal cones remains unclear. QUESTIONS/PURPOSES We developed and validated finite-element models of nine cadaveric specimens to determine: (1) whether using cones for addressing moderate metaphyseal tibial defects in revision TKA reduces the risk of implant-cement debonding compared with cementing the implant alone, and (2) when using metaphyseal cones, whether long, uncemented stems (or diaphyseal-engaging stems) reduce the risk of implant-cement debonding and the cone-bone micromotions compared with short, cemented stems. METHODS We divided nine cadaveric specimens (six male, three female, aged 57 to 73 years, BMI 24 to 47 kg/m2) with standardized tibial metaphyseal defects into three study groups: no cone with short (50-mm) cemented stem, in which the defect was filled with cement; cone with short (50-mm) cemented stem, in which a metaphyseal cone was implanted before cementing the implant; and cone with long, diaphyseal-engaging stem, which received a metaphyseal cone and the largest 150-mm stem that could fit the diaphyseal canal. The specimens were implanted and mechanically tested. Then, we developed and validated finite-element models to investigate the interaction between the implant and the bone during the demanding activity of stair ascent. We quantified the risk of implant debonding from the cement mantle by comparing the axial and shear stress at the cement-implant interface against an experimentally derived interface failure index criterion that has been previously used to quantify the risk of cement debonding. We considered the risk of debonding to be minimal when the failure index was below 10% of the strength of the interface (or failure index < 0.1). We also quantified the micromotion between the cone and the bone, as a guide to the likelihood of fixation by bone ingrowth. To this end, we assumed bone ingrowth for micromotion values below the most restrictive reported threshold for bone ingrowth, 20 µm. RESULTS When using a short, 50-mm cemented stem and cement alone to fill the defect, 77% to 86% of the cement-implant interface had minimal risk of debonding (failure index < 0.1). When using a short, 50-mm cemented stem with a cone, 87% to 93% of the cement-implant interface had minimal debonding risk. When combining a cone with a long (150-mm) uncemented stem, 92% to 94% of the cement-implant interface had minimal debonding risk. The differences in cone-bone micromotion between short, cemented stems and long, uncemented stems were minimal and, for both configurations, most cones had micromotions below the most restrictive 20-µm threshold for ingrowth. However, the maximum micromotion between the cone and the bone was in general smaller when using a long, uncemented stem (13-23 µm) than when using a short, cemented stem (11-31 µm). CONCLUSION Although the risk of debonding was low in all cases, metaphyseal cones help reduce the biomechanical burden on the implant-cement interface of short-stemmed implants in high-demand activities such as stair ascent. When using cones in revision TKA, long, diaphyseal-engaging stems did not provide a clear biomechanical advantage over short stems. Future studies should explore additional loading conditions, quantify the interspecimen variability, consider more critical defects, and evaluate the behavior of the reconstructive techniques under repetitive loads. CLINICAL RELEVANCE Cones and stems are routinely used to address tibial defects in revision TKA. Despite our finding that metaphyseal cones may help reduce the risk of implant-cement debonding and allow using shorter stems with comparable biomechanical behavior to longer stems, either cones or cement alone can provide comparable results in contained metaphyseal defects. However, longer term clinical studies are needed to compare these techniques over time.
Collapse
Affiliation(s)
| | - Kathleen N. Meyers
- Department of Biomechanics, Hospital for Special Surgery, New York, NY, USA
| | | | | | - Joseph D. Lipman
- Department of Biomechanics, Hospital for Special Surgery, New York, NY, USA
| | - Timothy M. Wright
- Department of Biomechanics, Hospital for Special Surgery, New York, NY, USA
| | - Michael P. Ast
- Complex Joint Reconstruction Center, Hospital for Special Surgery, New York, NY, USA
| |
Collapse
|
20
|
Steineman BD, González FJQ, Sturnick DR, Deland JT, Demetracopoulos CA, Wright TM. Biomechanical evaluation of total ankle arthroplasty. Part I: Joint loads during simulated level walking. J Orthop Res 2021; 39:94-102. [PMID: 33146417 PMCID: PMC7749051 DOI: 10.1002/jor.24902] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 06/02/2020] [Revised: 09/25/2020] [Accepted: 10/31/2020] [Indexed: 02/04/2023]
Abstract
In total ankle arthroplasty, the interaction at the joint between implant and bone is driven by a complex loading environment. Unfortunately, little is known about the loads at the ankle during daily activities since earlier attempts use two- or three-dimensional models to explore simplified joint mechanics. Our goal was to develop a framework to calculate multi-axial loads at the joint during simulated level walking following total ankle arthroplasty. To accomplish this, we combined robotic simulations of level walking at one-quarter bodyweight in three cadaveric foot and ankle specimens with musculoskeletal modeling to calculate the multi-axial forces and moments at the ankle during the stance phase. The peak compressive forces calculated were between 720 and 873 N occurring around 77%-80% of stance. The peak moment, which was the internal moment for all specimens, was between 6.1 and 11.6 N m and occurred between 72% and 88% of the stance phase. The peak moment did not necessarily occur with the peak force. The ankle joint loads calculated in this study correspond well to previous attempts in the literature; however, our robotic simulator and framework provide an opportunity to resolve the resultant three-dimensional forces and moments as others have not in previous studies. The framework may be useful to calculate ankle joint loads in cadaveric specimens as the first step in evaluating bone-implant interactions in total ankle replacement using specimen specific inputs. This approach also provides a unique opportunity to evaluate changes in joint loads and kinematics following surgical interventions of the foot and ankle.
Collapse
Affiliation(s)
- Brett D. Steineman
- Department of Biomechanics, Hospital for Special Surgery, New York, NY USA
| | | | - Daniel R. Sturnick
- Department of Biomechanics, Hospital for Special Surgery, New York, NY USA
| | | | | | - Timothy M. Wright
- Department of Biomechanics, Hospital for Special Surgery, New York, NY USA
| |
Collapse
|
21
|
Small SR, Rogge RD, Reyes EM, Seale RB, Elliott JB, Malinzak RA. Primary Stability in Cementless Rotating Platform Total Knee Arthroplasty. J Knee Surg 2021; 34:192-199. [PMID: 31394587 DOI: 10.1055/s-0039-1694055] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 02/07/2023]
Abstract
Highly porous ingrowth surfaces have been introduced into tibial tray fixation to improve long-term survivorship in cementless total knee arthroplasty. This study was designed to evaluate the effect of porous ingrowth surface on primary stability in the implanted cementless tibial component. Three tibial tray designs possessing sintered bead or roughened porous coating ingrowth surfaces were implanted into a foam tibia model with primary stability assessed via digital image correlation during stair descent and condylar liftoff loading. Follow-up testing was conducted by implanting matched-pair cadaveric tibias with otherwise identical trays with two iterations of ingrowth surface design. Trays were loaded and micromotion evaluated in a condylar liftoff model. The sintered bead tibial tray exhibited slightly lower micromotion than the roughened porous coating in stair descent loading. However, no significant difference in primary stability was observed in condylar liftoff loading in either foam or cadaveric specimens. Cementless tibial trays featuring two different iterations of porous ingrowth surfaces demonstrated both good stability in cadaveric specimens with less than 80 microns of micromotion and 1 mm of subsidence under cyclic loading. While improved ingrowth surfaces may lead to improved biological fixation and long-term osteointegration, this study was unable to identify a difference in primary stability associated with subsequent ingrown surface design iteration.
Collapse
Affiliation(s)
- Scott R Small
- Department of Orthopaedic Biomedical Engineering, Joint Replacement Surgeons of Indiana Research Foundation, Mooresville, Indiana
| | - Renee D Rogge
- Department of Biology and Biomedical Engineering, Rose-Hulman Institute of Technology, Terre Haute, Indiana
| | - Eric M Reyes
- Department of Mathematics, Rose-Hulman Institute of Technology, Terre Haute, Indiana
| | - Ryan B Seale
- Department of Biology and Biomedical Engineering, Rose-Hulman Institute of Technology, Terre Haute, Indiana
| | - Jeffrey B Elliott
- Department of Biology and Biomedical Engineering, Rose-Hulman Institute of Technology, Terre Haute, Indiana
| | - Robert A Malinzak
- Department of Orthopaedic Biomedical Engineering, Joint Replacement Surgeons of Indiana Research Foundation, Mooresville, Indiana
| |
Collapse
|
22
|
Han S, Patel RV, Ismaily SK, Jones HL, Gold JE, Noble PC. Micromotion and Migration of Cementless Tibial Trays Under Functional Loading Conditions. J Arthroplasty 2021; 36:349-355. [PMID: 32741712 DOI: 10.1016/j.arth.2020.07.017] [Citation(s) in RCA: 9] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 04/27/2020] [Revised: 05/29/2020] [Accepted: 07/06/2020] [Indexed: 02/02/2023] Open
Abstract
BACKGROUND The outcome of cementless total knee arthroplasty (TKA) relies on successful bony ingrowth into the implant surfaces. Failures due to aseptic loosening are still reported, especially in younger and more active patients. The objective of this study is to quantify the micromotion of a commercially available design of cementless tibial tray under loading conditions simulating walking and stair descent. METHOD A commercially available design of cementless total knee arthroplasty was implanted in 7 cadaveric knees which were preconditioned with 500 cycles of 0°-100° flexion under a vertical load of 1050 N in a custom-built, multiaxial functional activity simulator. This was followed by application of the peak forces and moments occurring during walking and stair descent. During each loading procedure, 3-dimensional motion at the bone-prosthesis interface was measured using digital image correlation. RESULTS The tray migrated 101 ± 25 μm on average during preconditioning, which was dominated by rotation in the sagittal plane (92% of total migration), combined with posterior translation (28%) and minimal rotation in the transverse plane (14%). The migration varied 2.7-fold (61-167 μm) between the 6 measurement zones. Stair descent produced significantly higher total micromotion than walking in zone #5 (62 ± 9 vs 51 ± 10 μm, P < .05) and zone #6 (68 ± 17 vs 37 ± 10 μm, P < .05). In addition, during stair descent, the tray exhibited significantly more tilting (anterior zones: 31 ± 17 vs -16 ± 20 μm, P < .05; posterior zones: -60 ± 8 vs -40 ± 7 μm, P < .05) and more anteroposterior displacement in the anterior zones (-25 ± 3 vs -13 ± 2 μm, P < .05) when compared to walking. CONCLUSION The relative motion at the bone-prosthesis interface varied substantially around the periphery of the cementless tray. Under the loading conditions evaluated, the tray primarily underwent a rocking motion in the sagittal plane. Compared with walking, stair descent produced significantly more micromotion, especially in the posterior zones.
Collapse
Affiliation(s)
- Shuyang Han
- Institute of Orthopedic Research and Education, Houston, Texas; Department of Orthopedic Surgery, McGovern Medical School, UTHealth, Houston, Texas
| | - Rikin V Patel
- Institute of Orthopedic Research and Education, Houston, Texas
| | - Sabir K Ismaily
- Institute of Orthopedic Research and Education, Houston, Texas; Department of Orthopedic Surgery, McGovern Medical School, UTHealth, Houston, Texas
| | - Hugh L Jones
- Institute of Orthopedic Research and Education, Houston, Texas; Department of Orthopedic Surgery, McGovern Medical School, UTHealth, Houston, Texas
| | - Jonathan E Gold
- Institute of Orthopedic Research and Education, Houston, Texas; Department of Orthopedic Surgery, McGovern Medical School, UTHealth, Houston, Texas
| | - Philip C Noble
- Institute of Orthopedic Research and Education, Houston, Texas; Department of Orthopedic Surgery, McGovern Medical School, UTHealth, Houston, Texas
| |
Collapse
|
23
|
González FJQ, Steineman BD, Sturnick DR, Deland JT, Demetracopoulos CA, Wright TM. Biomechanical evaluation of total ankle arthroplasty. Part II: Influence of loading and fixation design on tibial bone-implant interaction. J Orthop Res 2021; 39:103-111. [PMID: 33030768 PMCID: PMC7748995 DOI: 10.1002/jor.24876] [Citation(s) in RCA: 13] [Impact Index Per Article: 4.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 06/02/2020] [Revised: 09/04/2020] [Accepted: 10/06/2020] [Indexed: 02/04/2023]
Abstract
Finite element (FE) models to evaluate the burden placed on the interaction between total ankle arthroplasty (TAA) implants and the bone often rely on peak axial forces. However, the loading environment of the ankle is complex, and it is unclear whether peak axial forces represent a challenging scenario for the interaction between the implant and the bone. Our goal was to determine how the loads and the design of the fixation of the tibial component of TAA impact the interaction between the implant and the bone. To this end, we developed a framework that integrated robotic cadaveric simulations to determine the ankle kinematics, musculoskeletal models to determine the ankle joint loads, and FE models to evaluate the interaction between TAA and the bone. We compared the bone-implant micromotion and the risk of bone failure of three common fixation designs for the tibial component of TAA: spikes, a stem, and a keel. We found that the most critical conditions for the interaction between the implant and the bone were dependent on the specimen and the fixation design, but always involved submaximal forces and large moments. We also found that while the fixation design influenced the distribution and the peak value of bone-implant micromotion, the amount of bone at risk of failure was specimen dependent. To account for the most critical conditions for the interaction between the implant and the bone, our results support simulating multiple specimens under complex loading profiles that include multiaxial moments and span entire activity cycles.
Collapse
Affiliation(s)
| | - Brett D Steineman
- Department of Biomechanics, Hospital for Special Surgery, New York, NY USA
| | - Daniel R Sturnick
- Department of Biomechanics, Hospital for Special Surgery, New York, NY USA
| | - Jonathan T. Deland
- Department of Foot and Ankle Surgery, Hospital for Special Surgery, New York, NY, USA
| | | | - Timothy M Wright
- Department of Biomechanics, Hospital for Special Surgery, New York, NY USA
| |
Collapse
|
24
|
Investigation of Biomechanical Characteristics of Orthopedic Implants for Tibial Plateau Fractures by Means of Deep Learning and Support Vector Machine Classification. APPLIED SCIENCES-BASEL 2020. [DOI: 10.3390/app10144697] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 01/06/2023]
Abstract
An experimental comparative study of the biomechanical behavior of commonly used orthopedic implants for tibial plateau fractures was carried out. An artificial bone model Synbone1110 was used and a Schatzker V type tibial plateau fracture was created in vitro, then stabilized with three different implant types, classic L plate, Locking Plate System (PLS), and Hybrid External Fixator (HEF). The stiffness of the bone—implant assembly was assessed by means of mechanical testing using an automated testing machine. It was found that the classic L plate type internal implant has a significantly higher value of deformation then the other two implant types. In case of the other implant types, PLS had a better performance than HEF at low and medium values of the applied force. At high values of the applied forces, the difference between deformation values of the two types became gradually smaller. An Artificial Neural Network model was developed to predict the implant deformation as a function of the applied force and implant device type. To establish if a clear-cut distinction exists between mechanical performance of PLS and HEF, a Support Vector Machine classifier was employed. At high values of the applied force, the Support Vector Machine (SVM) classifier predicts that no statistically significant difference exists between the performance of PLS and HEF.
Collapse
|
25
|
Xie S, Conlisk N, Hamilton D, Scott C, Burnett R, Pankaj P. A finite element analysis of tibial tritanium cones without stems in varying bone defects. Knee 2020; 27:656-666. [PMID: 32563420 DOI: 10.1016/j.knee.2020.02.019] [Citation(s) in RCA: 6] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 10/15/2019] [Revised: 01/24/2020] [Accepted: 02/27/2020] [Indexed: 02/02/2023]
Abstract
BACKGROUND In the UK around 10% of hip and knee arthroplasties are revision operations. At revision total knee arthroplasty (rTKA), bone loss management is critical to achieving a stable bone-implant construct. Though tritanium cones have been used to manage bone defects in rTKA, their biomechanical performance with varying defects remains unknown. METHODS Uncontained tibial bone defects at four anatomic locations, with varying depths and widths (Type T2A and T2B) were investigated computationally in a composite tibia which was subjected to four loading scenarios. The ability of the tritanium cone to replace the tibial bone defect was examined using the outcome measures of bone strain distribution and interface micromotions. RESULTS It was found that anterior and lateral defects do not significantly alter the strain distribution compared with intact bone. For medial defects, strain distribution is sensitive to defect width; while strain distributions for posterior defects are associated with defect width and depth. In general, micromotions at the bone-implant interface are small and are primarily influenced by defect depth. CONCLUSIONS Our models show that the cone is an acceptable choice for bone defect management in rTKA. Since all observed micromotions were small, successful osteointegration would be expected in all types of uncontained defects considered in this study. Tritanium cones safely accommodate uncontained tibial defects up to 10 mm deep and extending up to 9 mm from the centre of the cone. Medial and posteriorly based defects managed with symmetric cones display the greatest bone strains and asymmetric cones may be useful in this context.
Collapse
Affiliation(s)
- Shuqiao Xie
- School of Engineering, Institute for Bioengineering, The University of Edinburgh, Alrick Building, The King's Buildings, Edinburgh EH9 3BF, UK
| | - Noel Conlisk
- School of Engineering, Institute for Bioengineering, The University of Edinburgh, Alrick Building, The King's Buildings, Edinburgh EH9 3BF, UK
| | - David Hamilton
- Department of Orthopaedics and Trauma, The University of Edinburgh, 49 Little France Crescent, Edinburgh, EH16 4SB, UK
| | - Chloe Scott
- Department of Orthopaedics and Trauma, Royal Infirmary of Edinburgh, 51 Little France Crescent, Edinburgh, EH16 4SB, UK
| | - Richard Burnett
- Department of Orthopaedics and Trauma, Royal Infirmary of Edinburgh, 51 Little France Crescent, Edinburgh, EH16 4SB, UK
| | - Pankaj Pankaj
- School of Engineering, Institute for Bioengineering, The University of Edinburgh, Alrick Building, The King's Buildings, Edinburgh EH9 3BF, UK.
| |
Collapse
|
26
|
Xie S, Conlisk N, Hamilton D, Scott C, Burnett R, Pankaj P. Metaphyseal cones in revision total knee arthroplasty: The role of stems. Bone Joint Res 2020; 9:162-172. [PMID: 32431807 PMCID: PMC7229340 DOI: 10.1302/2046-3758.94.bjr-2019-0239.r1] [Citation(s) in RCA: 26] [Impact Index Per Article: 6.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 11/06/2022] Open
Abstract
Aims Metaphyseal tritanium cones can be used to manage the tibial bone loss commonly encountered at revision total knee arthroplasty (rTKA). Tibial stems provide additional fixation and are generally used in combination with cones. The aim of this study was to examine the role of the stems in the overall stability of tibial implants when metaphyseal cones are used for rTKA. Methods This computational study investigates whether stems are required to augment metaphyseal cones at rTKA. Three cemented stem scenarios (no stem, 50 mm stem, and 100 mm stem) were investigated with 10 mm-deep uncontained posterior and medial tibial defects using four loading scenarios designed to mimic activities of daily living. Results Small micromotions (mean < 12 µm) were found to occur at the bone-implant interface for all loading cases with or without a stem. Stem inclusion was associated with lower micromotion, however these reductions were too small to have any clinical significance. Peak interface micromotion, even when the cone is used without a stem, was too small to effect osseointegration. The maximum difference occurred with stair descent loading. Stress concentrations in the bone occurred around the inferior aspect of each implant, with the largest occurring at the end of the long stem; these may lead to end-of-stem pain. Stem use is also found to result in stress shielding in the bone along the stem. Conclusion When a metaphyseal cone is used at rTKA to manage uncontained posterior or medial defects of up to 10 mm depth, stem use may not be necessary. Cite this article:Bone Joint Res. 2020;9(4):162–172.
Collapse
Affiliation(s)
- Shuqiao Xie
- School of Engineering, Institute for Bioengineering, The University of Edinburgh, Edinburgh, UK
| | - Noel Conlisk
- School of Engineering, Institute for Bioengineering, The University of Edinburgh, Edinburgh, UK
| | - David Hamilton
- Department of Orthopaedics and Trauma, The University of Edinburgh, Edinburgh, UK
| | - Chloe Scott
- Department of Orthopaedics, Royal Infirmary of Edinburgh, Edinburgh, UK
| | - Richard Burnett
- Department of Orthopaedics, Royal Infirmary of Edinburgh, Edinburgh, UK
| | - Pankaj Pankaj
- School of Engineering, Institute for Bioengineering, The University of Edinburgh, Edinburgh, UK
| |
Collapse
|
27
|
Yang H, Bayoglu R, Renani MS, Behnam Y, Navacchia A, Clary C, Rullkoetter PJ. Validation and sensitivity of model-predicted proximal tibial displacement and tray micromotion in cementless total knee arthroplasty under physiological loading conditions. J Mech Behav Biomed Mater 2020; 109:103793. [PMID: 32347217 DOI: 10.1016/j.jmbbm.2020.103793] [Citation(s) in RCA: 10] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/09/2020] [Revised: 03/29/2020] [Accepted: 04/12/2020] [Indexed: 11/30/2022]
Abstract
The initial fixation of cementless tibial trays after total knee arthroplasty is crucial to bony ingrowth onto the porous surface of the implants, as micromotion magnitudes exceeding 150 μm may inhibit bone formations and limit fixation. Experimental measurement of the interface micromotions is still very challenging. Thus, previous studies investigated micromotions at the bone-tray interface via finite element methods, but few performed direct validation via in vitro cadaveric testing under physiological loading conditions. Additionally, previous models were validated by solely considering relative displacements of the marker couples placed around the tray-bone interface. In this paper, we present an experimental-computational validation framework for investigating micromotions at the tray-bone interface under physiological conditions. Three cadaveric specimens were implanted with cementless rotating-platform implants and tested under gait, deep knee bending, and stair descent loads. Corresponding subject-specific finite element models were developed and used to predict the marker (tray-bone) relative displacements and tibial surface displacements. Experimental measurements were used to validate model estimations. Subsequent sensitivity analyses were performed on implantation and friction parameters to represent model uncertainties. The models appropriately differentiated between locations, activities, and specimens. The average root-mean-square (RMS) differences and correlations between measured marker relative displacements and predictions from the 'best-matching' models were 13.1 μm and 0.86. RMS differences and correlations between measured surface displacements and predictions were 78.9 μm and 0.84. Full-field interface micromotions were investigated and compared with predicted marker relative displacements. The marker relative displacements underestimated the actual interface micromotions. Initial tray-bone alignment in anterior-posterior, flexion-extension, and varus-valgus degrees of freedom have a considerable impact on the interface micromotions. The validated cadaveric models can be further used for pre-clinical assessments of new TKR tray design. The outcomes of the sensitivity analyses provide further insights into reducing interface micromotions via clinical techniques.
Collapse
Affiliation(s)
- Huizhou Yang
- Center for Orthopaedic Biomechanics, University of Denver, Denver, CO, 80208, USA
| | - Riza Bayoglu
- Center for Orthopaedic Biomechanics, University of Denver, Denver, CO, 80208, USA
| | | | - Yashar Behnam
- Center for Orthopaedic Biomechanics, University of Denver, Denver, CO, 80208, USA
| | - Alessandro Navacchia
- Center for Orthopaedic Biomechanics, University of Denver, Denver, CO, 80208, USA
| | - Chadd Clary
- Center for Orthopaedic Biomechanics, University of Denver, Denver, CO, 80208, USA
| | - Paul J Rullkoetter
- Center for Orthopaedic Biomechanics, University of Denver, Denver, CO, 80208, USA.
| |
Collapse
|
28
|
De Roeck J, Van Houcke J, Almeida D, Galibarov P, De Roeck L, Audenaert EA. Statistical Modeling of Lower Limb Kinetics During Deep Squat and Forward Lunge. Front Bioeng Biotechnol 2020; 8:233. [PMID: 32300586 PMCID: PMC7142215 DOI: 10.3389/fbioe.2020.00233] [Citation(s) in RCA: 9] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/30/2019] [Accepted: 03/06/2020] [Indexed: 11/24/2022] Open
Abstract
Purpose Modern statistics and higher computational power have opened novel possibilities to complex data analysis. While gait has been the utmost described motion in quantitative human motion analysis, descriptions of more challenging movements like the squat or lunge are currently lacking in the literature. The hip and knee joints are exposed to high forces and cause high morbidity and costs. Pre-surgical kinetic data acquisition on a patient-specific anatomy is also scarce in the literature. Studying the normal inter-patient kinetic variability may lead to other comparable studies to initiate more personalized therapies within the orthopedics. Methods Trials are performed by 50 healthy young males who were not overweight and approximately of the same age and activity level. Spatial marker trajectories and ground reaction force registrations are imported into the Anybody Modeling System based on subject-specific geometry and the state-of-the-art TLEM 2.0 dataset. Hip and knee joint reaction forces were obtained by a simulation with an inverse dynamics approach. With these forces, a statistical model that accounts for inter-subject variability was created. For this, we applied a principal component analysis in order to enable variance decomposition. This way, noise can be rejected and we still contemplate all waveform data, instead of using deduced spatiotemporal parameters like peak flexion or stride length as done in many gait analyses. In addition, this current paper is, to the authors’ knowledge, the first to investigate the generalization of a kinetic model data toward the population. Results Average knee reaction forces range up to 7.16 times body weight for the forwarded leg during lunge. Conversely, during squat, the load is evenly distributed. For both motions, a reliable and compact statistical model was created. In the lunge model, the first 12 modes accounts for 95.26% of inter-individual population variance. For the maximal-depth squat, this was 95.69% for the first 14 modes. Model accuracies will increase when including more principal components. Conclusion Our model design was proved to be compact, accurate, and reliable. For models aimed at populations covering descriptive studies, the sample size must be at least 50.
Collapse
Affiliation(s)
- Joris De Roeck
- Department of Human Structure and Repair, Ghent University, Ghent, Belgium
| | - J Van Houcke
- Department of Human Structure and Repair, Ghent University, Ghent, Belgium
| | - D Almeida
- Centre for Rapid and Sustainable Product Development, Polytechnic Institute of Leiria, Leiria, Portugal
| | | | - L De Roeck
- Department of Human Structure and Repair, Ghent University, Ghent, Belgium
| | - Emmanuel A Audenaert
- Department of Human Structure and Repair, Ghent University, Ghent, Belgium.,Department of Orthopaedic Surgery and Traumatology, Ghent University Hospital, Ghent, Belgium.,Department of Trauma and Orthopaedics, Addenbrooke's Hospital, Cambridge University Hospitals NHS Foundation Trust, Cambridge, United Kingdom.,Department of Electromechanics, Op3Mech Research Group, University of Antwerp, Antwerp, Belgium
| |
Collapse
|
29
|
Song SJ, Lee HW, Bae DK, Park CH. High Incidence of Tibial Component Loosening After Total Knee Arthroplasty Using Ceramic Titanium-Nitride-Coated Mobile Bearing Prosthesis in Moderate to Severe Varus Deformity: A Matched-Pair Study Between Ceramic-Coated Mobile Bearing and Fixed Bearing Prostheses. J Arthroplasty 2020; 35:1003-1008. [PMID: 31859013 DOI: 10.1016/j.arth.2019.11.034] [Citation(s) in RCA: 11] [Impact Index Per Article: 2.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 09/24/2019] [Revised: 11/20/2019] [Accepted: 11/21/2019] [Indexed: 02/01/2023] Open
Abstract
BACKGROUND We compared the incidence of aseptic component loosening and subsequent revision, and the survival rate between ceramic titanium-nitride-coated mobile bearing (MB) and fixed bearing total knee arthroplasties (TKAs) performed in patients with moderate to severe varus deformities. METHODS In total, 200 TKAs using advanced coated system posterior stabilized prostheses in varus deformity of mechanical axis >8° between 2012 and 2016 were retrospectively reviewed. One hundred MB (ceramic-m group) and 100 fixed bearing (ceramic-f group) prostheses were included. The matches were made according to preoperative demographics, range of motion, and severity of deformity. The mean follow-up period was not different (ceramic-m vs ceramic-f = 4.8 vs 5.1 years; P = .104). The incidence of revision TKA due to aseptic component loosening and the survival rate (failure: revision due to aseptic loosening) was investigated. RESULTS The incidence of revision TKA due to aseptic component loosening was 7 (7%) in the ceramic-m group and 1 (1%) in the ceramic-f group (P = .032). All cases of aseptic loosening occurred at the tibial component. The overall survival rate was 91.3% in the ceramic-m group and 98.9% in the ceramic-f group (P = .025). CONCLUSION Considering the higher revision incidence and lower survival rate due to tibial component loosening, caution should be taken in tibial component fixation when using advanced coated system MB prosthesis in moderate to severe varus deformity. LEVEL OF EVIDENCE III.
Collapse
Affiliation(s)
- Sang Jun Song
- Department of Orthopaedic Surgery, College of Medicine, Kyung Hee University, Seoul, South Korea
| | - Hyun Woo Lee
- Department of Orthopaedic Surgery, College of Medicine, Kyung Hee University, Seoul, South Korea
| | - Dae Kyung Bae
- Department of Orthopaedic Surgery, Seoul Sacred Heart General Hospital, Seoul, South Korea
| | - Cheol Hee Park
- Department of Medicine, Graduate School, Kyung Hee University, Seoul, South Korea
| |
Collapse
|
30
|
Hegarty P, Walls A, O'Brien S, Gamble B, Cusick L, Beverland DE. A Prospective Randomized Study Comparing Postoperative Pain, Biological Fixation, and Clinical Outcomes Between Two Uncemented Rotating Platform Tibial Tray Designs. J Arthroplasty 2020; 35:429-437. [PMID: 31629621 DOI: 10.1016/j.arth.2019.09.029] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 07/01/2019] [Revised: 09/09/2019] [Accepted: 09/17/2019] [Indexed: 02/01/2023] Open
Abstract
BACKGROUND With the demand for arthroplasty increasing worldwide year on year, there is a drive to improve prosthesis longevity. Biological fixation from cementless implants has been one method of trying to achieve this. We hypothesized that the addition of a hydroxyapatite (HA) coating and 4 pegs to a porous-coated tibial tray would provide a reduction in time to implant osseointegration, allowing for normal physiological stress transfer, thus improving early postoperative pain and rehabilitation as well as the elimination of radiolucent lines (RLLs). METHODS A prospective, randomized controlled single-blinded study was undertaken, comparing postoperative pain, radiographic evidence of biological fixation, and clinical outcomes between patients undergoing primary total knee arthroplasty with either LCS Complete POROCOAT (porous coating only) or LCS Complete DUOFIX (porous coating plus HA and pegs) knee systems (DePuy Synthes, Warsaw, IN). In total, 197 patients (205 knees) were recruited into the study between November 2006 and November 2008 and have been followed for up to 10 years. RESULTS There were no clinically significant differences in pain or patient-reported outcome measures when comparing the 2 designs but the tibial tray with pegs and HA showed fewer RLLs at all time points. There was no correlation between RLLs and pain and no instances of loosening or osteolysis in either group. There was 1 revision for infection in the porous coating only group. CONCLUSION The tray design with HA and additional fixation pegs did not confer any benefit in terms of reduced early postoperative pain or improved patient-reported outcomes, although it did result in significantly fewer RLLs. Both implants demonstrated excellent survivorship. With a cementless porous-coated tibial component, nonprogressive RLLs should be considered normal.
Collapse
Affiliation(s)
- Paul Hegarty
- Outcomes Department, Musgrave Park Hospital, Belfast, United Kingdom
| | - Andrew Walls
- Outcomes Department, Musgrave Park Hospital, Belfast, United Kingdom
| | - Seamus O'Brien
- Outcomes Department, Musgrave Park Hospital, Belfast, United Kingdom
| | - Barbara Gamble
- Outcomes Department, Musgrave Park Hospital, Belfast, United Kingdom
| | - Laurence Cusick
- Outcomes Department, Musgrave Park Hospital, Belfast, United Kingdom
| | - David E Beverland
- Outcomes Department, Musgrave Park Hospital, Belfast, United Kingdom
| |
Collapse
|
31
|
Hériveaux Y, Nguyen VH, Geiger D, Haïat G. Elastography of the bone-implant interface. Sci Rep 2019; 9:14163. [PMID: 31578440 PMCID: PMC6775155 DOI: 10.1038/s41598-019-50665-4] [Citation(s) in RCA: 7] [Impact Index Per Article: 1.4] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/07/2019] [Accepted: 09/17/2019] [Indexed: 01/04/2023] Open
Abstract
The stress distribution around endosseous implants is an important determinant of the surgical success. However, no method developed so far to determine the implant stability is sensitive to the loading conditions of the bone-implant interface (BII). The objective of this study is to investigate whether a quantitative ultrasound (QUS) technique may be used to retrieve information on compressive stresses applied to the BII. An acousto-mechanical device was conceived to compress 18 trabecular bovine bone samples onto coin-shaped implants and to measure the ultrasonic response of the BII during compression. The biomechanical behavior of the trabecular bone samples was modeled as Neo-Hookean. The reflection coefficient of the BII was shown to decrease as a function of the stress during the elastic compression of the trabecular bone samples and during the collapse of the trabecular network, with an average slope of −4.82 GPa−1. The results may be explained by an increase of the bone-implant contact ratio and by changes of bone structure occurring during compression. The sensitivity of the QUS response of the BII to compressive stresses opens new paths in the elaboration of patient specific decision support systems allowing surgeons to assess implant stability that should be developed in the future.
Collapse
Affiliation(s)
- Yoann Hériveaux
- CNRS, Laboratoire Modélisation et Simulation Multi Echelle, MSME UMR 8208 CNRS, 61 avenue du Général de Gaulle, 94010, Créteil Cedex, France
| | - Vu-Hieu Nguyen
- Université Paris-Est, Laboratoire Modélisation et Simulation Multi Echelle, MSME UMR 8208 CNRS, 61 avenue du Général de Gaulle, 94010, Créteil Cedex, France
| | - Didier Geiger
- Université Paris-Est, Laboratoire Modélisation et Simulation Multi Echelle, MSME UMR 8208 CNRS, 61 avenue du Général de Gaulle, 94010, Créteil Cedex, France
| | - Guillaume Haïat
- CNRS, Laboratoire Modélisation et Simulation Multi Echelle, MSME UMR 8208 CNRS, 61 avenue du Général de Gaulle, 94010, Créteil Cedex, France.
| |
Collapse
|
32
|
Gao X, Fraulob M, Haïat G. Biomechanical behaviours of the bone-implant interface: a review. J R Soc Interface 2019; 16:20190259. [PMID: 31362615 PMCID: PMC6685012 DOI: 10.1098/rsif.2019.0259] [Citation(s) in RCA: 97] [Impact Index Per Article: 19.4] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/08/2019] [Accepted: 07/01/2019] [Indexed: 01/09/2023] Open
Abstract
In recent decades, cementless implants have been widely used in clinical practice to replace missing organs, to replace damaged or missing bone tissue or to restore joint functionality. However, there remain risks of failure which may have dramatic consequences. The success of an implant depends on its stability, which is determined by the biomechanical properties of the bone-implant interface (BII). The aim of this review article is to provide more insight on the current state of the art concerning the evolution of the biomechanical properties of the BII as a function of the implant's environment. The main characteristics of the BII and the determinants of implant stability are first introduced. Then, the different mechanical methods that have been employed to derive the macroscopic properties of the BII will be described. The experimental multi-modality approaches used to determine the microscopic biomechanical properties of periprosthetic newly formed bone tissue are also reviewed. Eventually, the influence of the implant's properties, in terms of both surface properties and biomaterials, is investigated. A better understanding of the phenomena occurring at the BII will lead to (i) medical devices that help surgeons to determine an implant's stability and (ii) an improvement in the quality of implants.
Collapse
Affiliation(s)
- Xing Gao
- CNRS, Laboratoire Modélisation et Simulation Multi Echelle, UMR CNRS 8208, 61 avenue du Général de Gaulle, 94010 Créteil cedex, France
- Research Centre for Medical Robotics and Minimally Invasive Surgical Devices, Shenzhen Institutes of Advanced Technology, Chinese Academy of Sciences, Shenzhen 518055, People's Republic of China
| | - Manon Fraulob
- CNRS, Laboratoire Modélisation et Simulation Multi Echelle, UMR CNRS 8208, 61 avenue du Général de Gaulle, 94010 Créteil cedex, France
| | - Guillaume Haïat
- CNRS, Laboratoire Modélisation et Simulation Multi Echelle, UMR CNRS 8208, 61 avenue du Général de Gaulle, 94010 Créteil cedex, France
| |
Collapse
|
33
|
Awadalla M, Al-Dirini RMA, O'Rourke D, Solomon LB, Heldreth M, Rullkoetter P, Taylor M. Influence of stems and metaphyseal sleeve on primary stability of cementless revision tibial trays used to reconstruct AORI IIB defects. J Orthop Res 2019; 37:1033-1041. [PMID: 30677164 DOI: 10.1002/jor.24232] [Citation(s) in RCA: 9] [Impact Index Per Article: 1.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 06/03/2018] [Accepted: 01/08/2019] [Indexed: 02/04/2023]
Abstract
Metaphyseal augments, such as sleeves, have been introduced to augment the fixation of revision total knee replacement (rTKR) components, and can be used with or without a stem. The effect of sleeve size in combination with stems on the primary stability and load transfer of a rTKR implant in AORI type IIB defects where the defect involves both condyles are poorly understood. The aim of this study was to examine the primary stability of revision tibial tray augmented with a sleeve in an AORI type IIB defect which involves both condyles with loss of cortical and cancellous bone. Finite element models were generated from computed tomography (CT) scans of nine individuals. All the bones used in the study had an AORI type IIB defect. The cohort included eight females (mean weight: 64 kg, height: 1.6 m). Material properties were sampled from CT data and assigned to the FE model. Joint contact forces for level gait, stair descent, and squat were applied. Stemless sleeved implants under various loading conditions were shown to have adequate primary stability in all AORI type IIB defects investigated. Adding a stem only marginally improved the primary stability of the implant but reduced the strain in the metaphysis compared to stemless implants. Once good initial mechanical stability was established with a sleeve, there was no benefit, in terms of primary stability or bone strains, from increasing sleeve size. This study suggests that metaphyseal sleeves, without a stem, can provide the required primary stability required by a rTKR tibial implant, to reconstruct an AORI type IIB defect. © 2019 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res.
Collapse
Affiliation(s)
- Maged Awadalla
- Medical Device Research Institute, College of Science and Engineering, Flinders University, SA, Australia
| | - Rami M A Al-Dirini
- Medical Device Research Institute, College of Science and Engineering, Flinders University, SA, Australia
| | - Dermot O'Rourke
- Medical Device Research Institute, College of Science and Engineering, Flinders University, SA, Australia
| | - Lucian B Solomon
- Department of Orthopaedics and Trauma, Royal Adelaide Hospital, SA, Australia.,The University of Adelaide, Centre for Orthopaedic and Trauma Research, SA, Australia
| | - Mark Heldreth
- DePuy Synthes Inc., Joint Reconstruction, Warsaw, Indiana
| | - Paul Rullkoetter
- Department of Mechanical and Materials Engineering, University of Denver, Denver, Colorado
| | - Mark Taylor
- Medical Device Research Institute, College of Science and Engineering, Flinders University, SA, Australia
| |
Collapse
|
34
|
Quevedo González FJ, Lipman JD, Lo D, De Martino I, Sculco PK, Sculco TP, Catani F, Wright TM. Mechanical performance of cementless total knee replacements: It is not all about the maximum loads. J Orthop Res 2019; 37:350-357. [PMID: 30499604 DOI: 10.1002/jor.24194] [Citation(s) in RCA: 14] [Impact Index Per Article: 2.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 08/08/2018] [Accepted: 11/13/2018] [Indexed: 02/04/2023]
Abstract
Finite element (FE) models are frequently used to assess mechanical interactions between orthopedic implants and surrounding bone. However, FE studies are often limited by the small number of bones that are modeled; the use of normal bones that do not reflect the altered bone density distributions that result from osteoarthritis (OA); and the application of simplified load cases usually based on peak forces and without consideration of tibiofemoral kinematics. To overcome these limitations, we undertook an integrated approach to determine the most critical scenario for the interaction between an uncemented tibial component and surrounding proximal tibial bone. A cementless component, based on a modern design, was virtually implanted using computed-tomography scans from 13 patients with knee OA. FE simulations were performed across a demanding activity, stair ascent, by combining in vivo experimental forces from the literature with tibiofemoral kinematics measured from patients who had received the same design of knee component. The worst conditions for the bone-implant interaction, in terms of micromotion and percentage of interfacial bone mass at risk of failure, did not arise from the maximum applied loads. We also found large variability among bones and tibiofemoral kinematics sets. Our results suggest that future FE studies should not focus solely on peak loads as this approach does not consistently correlate to worst-case scenarios. Moreover, multiple load cases and multiple bones should be considered to best reflect variations in tibiofemoral kinematics, anatomy, and tissue properties. © 2018 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 37:350-357, 2019.
Collapse
Affiliation(s)
| | - Joseph D Lipman
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, New York
| | - Darrick Lo
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, New York
| | - Ivan De Martino
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, New York
| | - Peter K Sculco
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, New York
| | - Thomas P Sculco
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, New York
| | - Fabio Catani
- University of Modena and Reggio Emilia, Largo del Pozzo 71, 41124 Modena, Italy
| | - Timothy M Wright
- Hospital for Special Surgery, 535 East 71st Street, New York 10021, New York
| |
Collapse
|
35
|
Navacchia A, Clary CW, Wilson HL, Behnam YA, Rullkoetter PJ. Validation of model-predicted tibial tray-synthetic bone relative motion in cementless total knee replacement during activities of daily living. J Biomech 2018; 77:115-123. [DOI: 10.1016/j.jbiomech.2018.06.024] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/08/2017] [Revised: 06/21/2018] [Accepted: 06/24/2018] [Indexed: 10/28/2022]
|
36
|
Awadalla M, Al-Dirini RMA, O'Rourke D, Solomon LB, Heldreth M, Taylor M. Influence of varying stem and metaphyseal sleeve size on the primary stability of cementless revision tibial trays used to reconstruct AORI IIA defects. A simulation study. J Orthop Res 2018; 36:1876-1886. [PMID: 29327379 DOI: 10.1002/jor.23851] [Citation(s) in RCA: 17] [Impact Index Per Article: 2.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 08/08/2017] [Accepted: 12/14/2017] [Indexed: 02/04/2023]
Abstract
Traditionally, diaphyseal stems have been utilized to augment the stability of revision total knee replacement (rTKR) implants. More recently metaphyseal augments, such as sleeves, have been introduced to further augment component fixation. The effect of augments such as stems and sleeves have on the primary stability of a rTKR implant is poorly understood, however it has important implications on the complexity, costs and survivorship of the procedure. Finite element analysis was used to investigate the primary stability and strain distribution of various size stems and sleeves used in conjunction with a cementless revision tibial tray. The model was built from computer tomography images of a single healthy tibia obtained from an 81-year-old patient to which an Anderson Orthopaedic Research Institute (AORI) IIA defect was virtually added. The influences of varying body mass index (BMI) and bone modulus were also investigated. Stemless sleeves were found to provided adequate primary implant stability (average implant micro-motion <50 μm) for the studied defect. Addition of a stem did not enhance the primary stability. Furthermore, this study found that varying BMI and bone modulus had a considerable effect on strain distribution but negligible effect on micro-motion in the sleeve area. In conclusion, the addition of diaphyseal stem to a metaphyseal sleeve had little benefit in enhancing the primary stability of tibial trays augmented when simulating reconstructions of AORI IIA tibial defects. Additional studies are required to determine the relative benefit of the diaphyseal stem when using metaphyseal sleeves defects with more extensive bone loss. © 2018 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1876-1886, 2018.
Collapse
Affiliation(s)
- Maged Awadalla
- College of Science and Engineering, Flinders University, 1284 South Rd., Clovelly ParkAdelaide, South Australia, Australia
| | - Rami M A Al-Dirini
- College of Science and Engineering, Flinders University, 1284 South Rd., Clovelly ParkAdelaide, South Australia, Australia
| | - Dermot O'Rourke
- College of Science and Engineering, Flinders University, 1284 South Rd., Clovelly ParkAdelaide, South Australia, Australia
| | - Lucian B Solomon
- Department of Orthopaedics and Trauma, Royal Adelaide Hospital, South Australia, Australia.,Centre for Orthopaedic and Trauma Research, The University of Adelaide, South Australia, Australia
| | - Mark Heldreth
- DePuy Synthes Inc., Joint Reconstruction, Warsaw, Indiana
| | - Mark Taylor
- College of Science and Engineering, Flinders University, 1284 South Rd., Clovelly ParkAdelaide, South Australia, Australia
| |
Collapse
|
37
|
Kutzner I, Hallan G, Høl PJ, Furnes O, Gøthesen Ø, Figved W, Ellison P. Early aseptic loosening of a mobile-bearing total knee replacement. Acta Orthop 2018; 89:77-83. [PMID: 29105532 PMCID: PMC5810837 DOI: 10.1080/17453674.2017.1398012] [Citation(s) in RCA: 25] [Impact Index Per Article: 4.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 02/28/2017] [Accepted: 09/29/2017] [Indexed: 01/31/2023] Open
Abstract
Background and purpose - Registry-based studies have reported an increased risk of aseptic tibial loosening for the cemented Low Contact Stress (LCS) total knee replacement compared with other cemented designs; however, the reasons for this have not been established. We made a retrieval analysis with the aim of identifying the failure mechanism. Patients and methods - We collected implants, cement, tissue, blood, and radiographs from 32 failed LCS Complete cases. Damage to the tibial baseplate and insert was assessed. Exposure to wear products was quantified in 11 cases through analysis of periprosthetic tissue and blood. Implant alignment and bone cement thickness was compared with a control group of 43 non-revised cases. Results - Loosening of the tibial baseplate was the reason for revision in 25 retrievals, occurring at the implant-cement interface in 16 cases. Polishing was observed on the lower surface of the baseplate and correlated to the level of cobalt, chromium, and zirconium in the blood. No evidence of abnormally high polyethylene wear was present. For each 1 mm increase in cement thickness the odds of failure due to aseptic loosening decreased by 61%. Greater varus alignment was associated with a shorter time to failure. The roughness, Ra, of a new LCS baseplate's lower surface was 3.7 (SD 0.7) µm. Interpretation - Debonding of the tibial component at the implant-cement interface was the predominant cause of tibial aseptic loosening. A thin cement layer may partly explain the poor performance. Furthermore, the comparatively low tibial surface roughness and the lack of a keeled stem may have played a role in the failures observed.
Collapse
Affiliation(s)
- Ines Kutzner
- Department of Clinical Medicine, University of Bergen, Norway
- Julius Wolff Institute, Charité—Universitätsmedizin Berlin, Germany
| | - Geir Hallan
- The Norwegian Arthroplasty Register, Department of Orthopaedic Surgery, Haukeland University Hospital, Bergen, Norway
| | - Paul Johan Høl
- Department of Clinical Medicine, University of Bergen, Norway
- The Norwegian Arthroplasty Register, Department of Orthopaedic Surgery, Haukeland University Hospital, Bergen, Norway
| | - Ove Furnes
- Department of Clinical Medicine, University of Bergen, Norway
- The Norwegian Arthroplasty Register, Department of Orthopaedic Surgery, Haukeland University Hospital, Bergen, Norway
| | - Øystein Gøthesen
- Department of Clinical Medicine, University of Bergen, Norway
- The Norwegian Arthroplasty Register, Department of Orthopaedic Surgery, Haukeland University Hospital, Bergen, Norway
- Haugesund Hospital, Haugesund, Norway
| | - Wender Figved
- Orthopedic Department, Baerum Hospital, Vestre Viken Hospital Trust, Norway
| | - Peter Ellison
- Department of Clinical Medicine, University of Bergen, Norway
- Department of Mechanical Engineering, Imperial College London, UK
| |
Collapse
|
38
|
Berahmani S, Hendriks M, de Jong JJA, van den Bergh JPW, Maal T, Janssen D, Verdonschot N. Evaluation of interference fit and bone damage of an uncemented femoral knee implant. Clin Biomech (Bristol, Avon) 2018; 51:1-9. [PMID: 29132027 DOI: 10.1016/j.clinbiomech.2017.10.022] [Citation(s) in RCA: 9] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 11/04/2016] [Revised: 10/25/2017] [Accepted: 10/30/2017] [Indexed: 02/07/2023]
Abstract
BACKGROUND During implantation of an uncemented femoral knee implant, press-fit interference fit provides the primary stability. It is assumed that during implantation a combination of elastic and plastic deformation and abrasion of the bone will occur, but little is known about what happens at the bone-implant interface and how much press-fit interference fit is eventually achieved. METHODS Five cadaveric femora were prepared and implantation was performed by an experienced surgeon. Micro-CT- and conventional CT-scans were obtained pre- and post-implantation for geometrical measurements and to measure bone mineral density. Additionally, the position of the implant with respect to the bone was determined by optical scanning of the reconstructions. By measuring the differences in surface geometry, assessments were made of the cutting error, the actual interference fit, the amount of bone damage, and the effective interference fit. FINDINGS Our analysis showed an average cutting error of 0.67mm (SD 0.17mm), which pointed mostly towards bone under-resections. We found an average actual AP interference fit of 1.48mm (SD 0.27mm), which was close to the nominal value of 1.5mm. INTERPRETATION We observed combinations of bone damage and elastic deformation in all bone specimens, which showed a trend to be related with bone density. Higher bone density tended to lead to lower bone damage and higher elastic deformation. The results of the current study indicate different factors that interact while implanting an uncemented femoral knee component. This knowledge can be used to fine-tune design criteria of femoral components to achieve adequate primary stability for all patients.
Collapse
Affiliation(s)
- Sanaz Berahmani
- Radboud university medical center, Radboud Institute for Health Sciences, Orthopaedic Research Lab, P.O. Box 9101, 6500 HB Nijmegen, The Netherlands.
| | - Maartje Hendriks
- Radboud university medical center, Radboud Institute for Health Sciences, Orthopaedic Research Lab, P.O. Box 9101, 6500 HB Nijmegen, The Netherlands
| | - Joost J A de Jong
- NUTRIM School for Nutrition and Translational Research in Metabolism, Maastricht University Medical Center, Maastricht, The Netherlands; Department of Rheumatology, Maastricht University Medical Center, Maastricht, The Netherlands
| | - Joop P W van den Bergh
- NUTRIM School for Nutrition and Translational Research in Metabolism, Maastricht University Medical Center, Maastricht, The Netherlands; Department of Rheumatology, Maastricht University Medical Center, Maastricht, The Netherlands; Department of Internal Medicine, VieCuri Medical Center, Venlo, The Netherlands; Faculty of Medicine and Life Sciences, Hasselt University, Hasselt, Belgium
| | - Thomas Maal
- Radboud university medical center, Department of Oral and Maxillofacial Surgery, Nijmegen, The Netherlands
| | - Dennis Janssen
- Radboud university medical center, Radboud Institute for Health Sciences, Orthopaedic Research Lab, P.O. Box 9101, 6500 HB Nijmegen, The Netherlands
| | - Nico Verdonschot
- Radboud university medical center, Radboud Institute for Health Sciences, Orthopaedic Research Lab, P.O. Box 9101, 6500 HB Nijmegen, The Netherlands; Laboratory for Biomechanical Engineering, University of Twente, Enschede, The Netherlands
| |
Collapse
|
39
|
Experimental and computational analysis of micromotions of an uncemented femoral knee implant using elastic and plastic bone material models. J Biomech 2017; 61:137-143. [DOI: 10.1016/j.jbiomech.2017.07.023] [Citation(s) in RCA: 12] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/20/2016] [Revised: 07/05/2017] [Accepted: 07/16/2017] [Indexed: 11/22/2022]
|
40
|
Prediction of stemless humeral implant micromotion during upper limb activities. Clin Biomech (Bristol, Avon) 2016; 36:46-51. [PMID: 27236035 DOI: 10.1016/j.clinbiomech.2016.05.003] [Citation(s) in RCA: 22] [Impact Index Per Article: 2.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 03/04/2016] [Revised: 04/29/2016] [Accepted: 05/05/2016] [Indexed: 02/07/2023]
Abstract
BACKGROUND Adequate primary stability is essential for the long term success of uncemented stemless shoulder implants. The goal of this study was to evaluate the micromotion of a stemless humeral implant during various upper limb activities. METHODS A finite element model was validated by reproducing experimental primary stability testing. Loading from an instrumented prosthesis representing a set of 29 upper limb activities were applied within the validated FE model. Peak micromotion and percentage area for different micromotion thresholds were considered. FINDINGS In all simulated activities, at least 99% of the implant surface experienced micromotion below 150μm. Micromotion depended strongly on loading with large discrepancies between upper limb activities. Carrying no external weight and keeping the arm at lower angles induced lower micromotion. Activities representative of demanding manual labor generally led to higher micromotion. Axilla crutches led to lower micromotion than forearm crutches. Micromotion increased when a wheelchair was used on slopes above 2% inclination. INTERPRETATION Micromotions below the 150μm threshold below which bone ingrowth occurs were measured over at least 99% of the implant surface for all simulated activities. Peak micromotion dependence on activity type demonstrates the need to consider physiologic in vivo loading and the full contact interface in primary stability evaluations. Focusing on activities with no hand weight and low arm motions during the rehabilitation period may enhance primary stability. For patients unable to walk without aids, axilla crutches and motorized wheelchairs might be more beneficial than forearm crutches and manual drive wheelchairs respectively.
Collapse
|
41
|
Small SR, Rogge RD, Malinzak RA, Reyes EM, Cook PL, Farley KA, Ritter MA. Micromotion at the tibial plateau in primary and revision total knee arthroplasty: fixed versus rotating platform designs. Bone Joint Res 2016; 5:122-9. [PMID: 27095658 PMCID: PMC4852811 DOI: 10.1302/2046-3758.54.2000481] [Citation(s) in RCA: 20] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 06/24/2015] [Accepted: 02/29/2016] [Indexed: 02/02/2023] Open
Abstract
OBJECTIVES Initial stability of tibial trays is crucial for long-term success of total knee arthroplasty (TKA) in both primary and revision settings. Rotating platform (RP) designs reduce torque transfer at the tibiofemoral interface. We asked if this reduced torque transfer in RP designs resulted in subsequently reduced micromotion at the cemented fixation interface between the prosthesis component and the adjacent bone. METHODS Composite tibias were implanted with fixed and RP primary and revision tibial trays and biomechanically tested under up to 2.5 kN of axial compression and 10° of external femoral component rotation. Relative micromotion between the implanted tibial tray and the neighbouring bone was quantified using high-precision digital image correlation techniques. RESULTS Rotational malalignment between femoral and tibial components generated 40% less overall tibial tray micromotion in RP designs than in standard fixed bearing tibial trays. RP trays reduced micromotion by up to 172 µm in axial compression and 84 µm in rotational malalignment models. CONCLUSIONS Reduced torque transfer at the tibiofemoral interface in RP tibial trays reduces relative component micromotion and may aid long-term stability in cases of revision TKA or poor bone quality.Cite this article: Mr S. R. Small. Micromotion at the tibial plateau in primary and revision total knee arthroplasty: fixed versus rotating platform designs. Bone Joint Res 2016;5:122-129. DOI: 10.1302/2046-3758.54.2000481.
Collapse
Affiliation(s)
- S R Small
- JRSI Foundation, Inc., 1199 Hadley Road, Mooresville, IN 46158, USA
| | - R D Rogge
- JRSI Foundation, Inc., 1199 Hadley Road, Mooresville, IN 46158, USA
| | - R A Malinzak
- JRSI Foundation, Inc., 1199 Hadley Road, Mooresville, IN 46158, USA
| | - E M Reyes
- Rose-Hulman Institute of Technology, 5500 Wabash Avenue, Terre Haute, IN 47803, USA
| | - P L Cook
- Rose-Hulman Institute of Technology, 5500 Wabash Avenue, Terre Haute, IN 47803, USA
| | - K A Farley
- Rose-Hulman Institute of Technology, 5500 Wabash Avenue, Terre Haute, IN 47803, USA
| | - M A Ritter
- Rose-Hulman Institute of Technology, 5500 Wabash Avenue, Terre Haute, IN 47803, USA
| |
Collapse
|
42
|
Four decades of finite element analysis of orthopaedic devices: where are we now and what are the opportunities? J Biomech 2014; 48:767-78. [PMID: 25560273 DOI: 10.1016/j.jbiomech.2014.12.019] [Citation(s) in RCA: 91] [Impact Index Per Article: 9.1] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Accepted: 11/26/2014] [Indexed: 11/23/2022]
Abstract
Finite element has been used for more than four decades to study and evaluate the mechanical behaviour total joint replacements. In Huiskes seminal paper "Failed innovation in total hip replacement: diagnosis and proposals for a cure", finite element modelling was one of the potential cures to avoid poorly performing designs reaching the market place. The size and sophistication of models has increased significantly since that paper and a range of techniques are available from predicting the initial mechanical environment through to advanced adaptive simulations including bone adaptation, tissue differentiation, damage accumulation and wear. However, are we any closer to FE becoming an effective screening tool for new devices? This review contains a critical analysis of currently available finite element modelling techniques including (i) development of the basic model, the application of appropriate material properties, loading and boundary conditions, (ii) describing the initial mechanical environment of the bone-implant system, (iii) capturing the time dependent behaviour in adaptive simulations, (iv) the design and implementation of computer based experiments and (v) determining suitable performance metrics. The development of the underlying tools and techniques appears to have plateaued and further advances appear to be limited either by a lack of data to populate the models or the need to better understand the fundamentals of the mechanical and biological processes. There has been progress in the design of computer based experiments. Historically, FE has been used in a similar way to in vitro tests, by running only a limited set of analyses, typically of a single bone segment or joint under idealised conditions. The power of finite element is the ability to run multiple simulations and explore the performance of a device under a variety of conditions. There has been increasing usage of design of experiments, probabilistic techniques and more recently population based modelling to account for patient and surgical variability. In order to have effective screening methods, we need to continue to develop these approaches to examine the behaviour and performance of total joint replacements and benchmark them for devices with known clinical performance. Finite element will increasingly be used in the design, development and pre-clinical testing of total joint replacements. However, simulations must include holistic, closely corroborated, multi-domain analyses which account for real world variability.
Collapse
|
43
|
Computationally efficient prediction of bone–implant interface micromotion of a cementless tibial tray during gait. J Biomech 2014; 47:1718-26. [DOI: 10.1016/j.jbiomech.2014.02.018] [Citation(s) in RCA: 23] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/26/2013] [Revised: 02/10/2014] [Accepted: 02/13/2014] [Indexed: 11/19/2022]
|
44
|
Taylor M, Bryan R, Galloway F. Accounting for patient variability in finite element analysis of the intact and implanted hip and knee: a review. INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN BIOMEDICAL ENGINEERING 2013; 29:273-292. [PMID: 23255372 DOI: 10.1002/cnm.2530] [Citation(s) in RCA: 20] [Impact Index Per Article: 1.8] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/24/2012] [Revised: 10/16/2012] [Accepted: 10/19/2012] [Indexed: 06/01/2023]
Abstract
It is becoming increasingly difficult to differentiate the performance of new joint replacement designs using available preclinical test methods. Finite element analysis is commonly used and the majority of published studies are performed on representative anatomy, assuming optimal implant placement, subjected to idealised loading conditions. There are significant differences between patients and accounting for this variability will lead to better assessment of the risk of failure. This review paper provides a comprehensive overview of the techniques available to account for patient variability. There is a brief overview of patient-specific model generation techniques, followed by a review of multisubject patient-specific studies performed on the intact and implanted femur and tibia. In particular, the challenges and limitations of manually generating models for such studies are discussed. To efficiently account for patient variability, the application of statistical shape and intensity models (SSIM) are being developed. Such models have the potential to synthetically generate thousands of representative models generated from a much smaller training set. Combined with the automation of the prosthesis implantation process, SSIM provides a potentially powerful tool for assessing the next generation of implant designs. The potential application of SSIM are discussed along with their limitations.
Collapse
Affiliation(s)
- Mark Taylor
- Medical Device Research Institute, School of Computer Science, Engineering and Mathematics, Flinders University, Adelaide, Australia.
| | | | | |
Collapse
|