Articular geometry can affect joint kinematics, contact mechanics, and implant-bone micromotion in total ankle arthroplasty

Effect of novel polyethylene insert configurations on bone-implant micromotion and contact stresses in total ankle replacement prostheses: a finite element analysis

Purpose

This study investigates the impact of elastic improvements to the artificial ankle joint insert on prosthesis biomechanics to reduce the risk of prosthesis loosening in TAR patients.

Methods

CT data of the right ankle was collected from one elderly female volunteer. An original TAR model (Model A) was developed from CT images and the INBONE II implant system. The development of the new inserts adopts an elastic improvement design approach, where different geometric configurations of flexible layers are inserted into the traditional insert. The structure can be divided into continuous flexible layers and intermittent flexible layers. The flexible layers aim to improve the elasticity of the component by absorbing and dispersing more kinetic energy. The newly designed inserts are used to replace the original insert in Model A, resulting in the development of Models B-D. A finite element model of gait analysis was based by gait parameters. Discrepancies in micromotion and contact behaviour were analysed during the gait cycle, along with interface fretting and articular surface stress at 50% of the gait cycle.

Results

In terms of micromotion, the improved elastic models showed reduced micromotion at the tibial-implant interfaces compared to the original model. The peak average micromotion decreased by 12.1%, 13.1%, and 14.5% in Models B, C, and D, respectively. The micromotion distribution also improved in the improved models, especially in Model D. Regarding contact areas, all models showed increased contact areas of articular surfaces with axial load, with Models B, C, and D increasing by 26.8%, 23.9%, and 24.4%, respectively. Contact stress on articular surfaces increased with axial load, reaching peak stress during the late stance phase. Models with continuous flexible layer designs exhibited lower stress levels. The insert and the talar prosthetic articular surfaces showed more uniform stress distribution in the improved models.

Conclusion

Improving the elasticity of the insert can enhance component flexibility, absorb impact forces, reduce micromotion, and improve contact behavior. The design scheme of continuous flexible layers is more advantageous in transmitting and dispersing stress, providing reference value for insert improvement.

The novel magnesium-titanium hybrid cannulated screws for the treatment of vertical femoral neck fractures: Biomechanical evaluation

Background

Conventional cannulated screws are commonly used for internal fixation in the treatment of vertical femoral neck fractures. However, the noticeably high rates of undesirable outcomes such as nonunion, malunion, avascular necrosis, and fixation failure still troubled the patients and surgeons. It is urgent to develop new cannulated screws to improve the above clinical problems. The purpose of this study was to design a novel magnesium-titanium hybrid cannulated screw and to further evaluate its biomechanical performance for the treatment of vertical femoral neck fractures.

Methods

A novel magnesium-titanium hybrid cannulated screw was designed, and the conventional titanium cannulated screw was also modeled. The finite element models for vertical femoral neck fractures with magnesium-titanium hybrid cannulated screws and conventional cannulated screws were respectively established. The hip joint contact force during walking gait calculated by a subject-specific musculoskeletal multibody dynamics model, was used as loads and boundary conditions for both finite element models. The stress and displacement distributions of the cannulated screws and the femur, the micromotion of the fracture surfaces of the femoral neck, and the overall stiffness were calculated and analyzed using finite element models. The biomechanical performance of the Magnesium-Titanium hybrid cannulated screws was evaluated.

Results

The maximum stresses of the magnesium-titanium hybrid cannulated screws and the conventional cannulated screws were 451.5 ​MPa and 476.8 ​MPa, respectively. The maximum stresses of the femur with the above different cannulated screws were 140.3 ​MPa and 164.8 ​MPa, respectively. The maximum displacement of the femur with the hybrid cannulated screws was 6.260 ​mm, lower than the femur with the conventional cannulated screws, which was 7.125 ​mm. The tangential micromotions in the two orthogonal directions at the fracture surface of the femoral neck with the magnesium-titanium hybrid cannulated screws were comparable to those with the conventional cannulated screws. The overall stiffness of the magnesium-titanium hybrid cannulated screw system was 490.17 ​N/mm, higher than that of the conventional cannulated screw system, which was 433.92 ​N/mm.

Conclusion

The magnesium-titanium hybrid cannulated screw had superior mechanical strength and fixation stability for the treatment of the vertical femoral neck fractures, compared with those of the conventional cannulated screw, indicating that the magnesium-titanium hybrid cannulated screw has great potential as a new fixation strategy in future clinical applications.The translational potential of this article: This study highlights an innovative design of the magnesium-titanium hybrid cannulated screw for the treatment of vertical femoral neck fractures. The novel magnesium-titanium hybrid cannulated screw not only to provide sufficient mechanical strength and fixation stability but also to contribute to the promotion of fracture healing, which could provide a better treatment for the vertical femoral neck fractures, beneficially reducing the incidence of nonunion and reoperation rates.

Clinically useful finite element models of the natural ankle - A review

BACKGROUND

Biomechanical simulation of the foot and ankle complex is a growing research area but compared to simulation of joints such as hip and knee, it has been under investigated and lacks consistency in research methodology. The methodology is variable, data is heterogenous and there are no clear output criteria. Therefore, it is very difficult to correlate clinically and draw meaningful inferences.

METHODS

The focus of this review is finite element simulation of the native ankle joint and we will explore: the different research questions asked, the model designs used, ways the model rigour has been ensured, the different output parameters of interest and the clinical impact and relevance of these studies.

FINDINGS

The 72 published studies explored in this review demonstrate wide variability in approach. Many studies demonstrated a preference for simplicity when representing different tissues, with the majority using linear isotropic material properties to represent the bone, cartilage and ligaments; this allows the models to be complex in another way such as to include more bones or complex loading. Most studies were validated against experimental or in vivo data, but a large proportion (40%) of studies were not validated at all, which is an area of concern.

INTERPRETATION

Finite element simulation of the ankle shows promise as a clinical tool for improving outcomes. Standardisation of model creation and standardisation of reporting would increase trust, and enable independent validation, through which successful clinical application of the research could be realised.