Dissolution studies of drug formulations using ion-selective electrodes as sensors in an air-segmented continuous flow analyzer

Analytical technologies for real-time drug dissolution and precipitation testing on a small scale

Objectives

This review focuses on real-time analytics of drug dissolution and precipitation testing on a comparatively small scale.

Key findings

Miniaturisation of test equipment is an important trend in pharmaceutics, and several small-scale experiments have been reported for drug dissolution and precipitation testing. Such tests typically employ analytics in real-time. Fibre optic ultraviolet (UV) analytics has become a well-established method in this field. Novel imaging techniques are emerging that use visible or UV light; also promising is Fourier transform infrared imaging based on attenuated total reflection. More information than just a rate constant is obtained from these methods. The early phase of a dissolution process can be assessed and drug precipitation may eventually be observed. Some real-time techniques are particularly well suited to studying drug precipitation during formulation dispersion; for example, turbidity, focused beam reflectance measurement and Raman spectroscopy.

Summary

Small-scale dissolution tests equipped with real-time analytics have become important to screen drug candidates as well as to study prototype formulations in early development. Future approaches are likely to combine different analytical techniques including imaging. Miniaturisation started with mini-vessels or small vials and future assays of dissolution research will probably more often reach the level of parallel well plates and microfluidic channels.

Analytical methods for dissolution testing of nanosized drugs

OBJECTIVES

This mini-review describes the theoretical advantages of nanosizing drugs in terms of dissolution and the characterization of their behaviour with in-vitro dissolution testing.

KEY FINDINGS

It is shown that the increase in dissolution rate is not commensurate with common theories. The calculation of dissolution rate by surface area increase using the Nernst-Brunner equation is inappropriate since the diffusion layer, δ, cannot be assessed. These results highlight the importance of an appropriate experimental design to assess the dissolution rate in vitro, which will then serve as a building block for establishing in vitro-in vivo correlations. Several techniques to assess the amount of released drug in dissolution testing are discussed, some through a review of current literature (dialysis, turbidity measurement methods, fibre optics, asymmetrical flow-field-flow fractionation), some through experimental experience (ion-selective electrode and syringe filters). Further methods, such as microdialysis, ultrasonic resonance technology and centrifugal filter devices, are reviewed from literature with some additional data obtained in house. The techniques are further discussed with a view to coupling the results with simulation software tools such as STELLA© to predict the in-vivo behaviour of the drug. In doing so, it is necessary to generate experimental data on the dissolution rate, since this cannot be calculated directly from the surface increase of drug particles but rather depends on further factors such as the boundary layer thickness.

SUMMARY

It was concluded that syringe filters of appropriate pore size and the ion-selective electrode appear to be suitable for measurement of the dissolution rate of nanosized drugs.

The effect of polyethylene glycol on the charcoal adsorption of chlorpromazine studied by ion selective electrode potentiometry

BACKGROUND

This investigation was undertaken to study: a) the adsorption characteristics of chlorpromazine to activated charcoal and its formulations Carbomix powder and Ultracarbon tablets at gastric pH; b) the effect on chlorpromazine adsorption of polyethylene glycol and its combination with electrolyte lavage solution; c) the effect of the order of addition of polyethylene glycol-electrolyte lavage solution.

METHOD

Ion selective electrode potentiometry, based on the selective, direct and continuous response of a chlorpromazine-ion selective electrode to the concentration of the free drug, was used. Successive additions of microvolumes of a chlorpromazine solution were made into a charcoal slurry in acidic medium of pH 1.2 with measurement of the chlorpromazine-ion selective electrode potential at equilibrium.

RESULTS

The maximum adsorption capacity values of activated charcoal, Carbomix and Ultracarbon, were 297, 563, and 382 mg/g respectively, while the affinity constant values were 40.2, 70.4, and 40.5 L/g, respectively. The adsorption of chlorpromazine to each of the Ultracarbon and Carbomix components was compared to the total adsorption of the formulations. The addition of polyethylene glycol-electrolyte lavage solution causes a slight desorption of chlorpromazine from activated charcoal at gastric pH, more pronounced when polyethylene glycol-electrolyte lavage solution follows the addition of activated charcoal, suggesting the possibility of a nonspecific binding of chlorpromazine to polyethylene glycol. The amount of chlorpromazine absorbed to Carbomix and Ultracarbon was not significantly affected at gastric pH by the presence of polyethylene glycol or polyethylene glycol-electrolyte lavage solution added either concurrently or sequentially to these formulations.

Construction of a diflunisal ion sensor and its use in automated flow-injection methods for assay, content uniformity, and dissolution studies of formulations

A diflunisal ion selective electrode of the PVC membrane type with an ion-exchanger consisting of the tetraheptylammonium-diflunisal ion pair is described. The sensor exhibits a rapid, near-Nernstian, selective response to diflunisal anion in the pH range 7-10, with a (batch) detection limit of 1 x 10(-5) M. The ion sensor was used as a flow detector in an automated flow-injection analyzer to develop routine methods for assays (concentration range 1-50 x 10(-4) M, (flow) detection limit 2.6 x 10(-5) M), content uniformity, and dissolution studies of diflunisal formulations. No serious interference from common ions and tablet excipients was found, and the drug can be directly determined in colored samples without separation steps. Fourty measurements can be performed automatically per hour with a precision of 0.5-1.8% relative standard deviation. The automated method for the dissolution test provides a complete dissolution profile by the end of the experiment. Using the constructed ion sensor, the intramolecular hydrogen bonding of the diflunisal anion was studied, thereby revealing a new application of ion sensor potentiometry.

Binding study of the fluorescence probe 1-anilino-8-naphthalensulfonate to human plasma and human and bovine serum albumin using potentiometric titration

The binding of 1-anilino-8-naphthalenesulfonate (ANS) to bovine serum albumin (BSA), human serum albumin (HSA), and human plasma has been studied by potentiometric titration utilizing a laboratory constructed ion selective electrode (ISE) of ANS. Three classes of ANS binding sites were found on BSA, HSA, and plasma at 25 and 37 degrees C. Computer analysis of the data resulted in estimates for the association constants, number of binding sites (HSA, BSA), and binding capacity of each class. The association constants for the first class of binding sites at 25 degrees C were found to be 7.53 (+/- 0.59) x 10(5), 2.70 (+/- 0.20) x 10(5), and 2.64 (+/- 0.26) x 10(5) M-1 for BSA, HSA, and plasma, respectively. Lower values for the association constants of all binding classes were estimated at the higher temperature (37 degrees C). The binding capacity for ANS decreased in the order BSA, plasma, HSA.