Totally organic biphasic solvent systems for extraction and descriptor determinations

Assessment of liquid-liquid partition for the assignment of descriptors for the solvation parameter model

The solvation parameter model uses five system independent descriptors to characterize compound properties defined as excess molar refraction, E, dipolarity/polarizability, S, hydrogen-bond acidity, A, hydrogen-bond basicity, B, and McGowan's characteristic volume, V, to model transfer properties between condensed phases. The V descriptor is assigned from structure. For compounds liquid at 20 °C the E descriptor can be assigned from the characteristic volume and its refractive index. The E descriptor for compounds solid at 20 °C and the S, A, and B descriptors are experimental properties traditionally assigned from chromatographic, liquid-liquid partition, and solubility measurements. In this report liquid-liquid partition constants in totally organic and aqueous biphasic systems are evaluated as a standalone technique for descriptor assignments. Using six totally organic biphasic systems the S, A, and B descriptors were assigned with an average absolute deviation (AAD) of about 0.04, 0.03, and 0.04, respectively, compared with the best estimate of the true descriptor values for 65 compounds. The E descriptor for compounds solid at 20 °C can only be estimated with an AAD of approximately 0.1. For six aqueous biphasic systems the B descriptor is assigned with a lower AAD of 0.028 and higher AAD of 0.08 and 0.05 for the S and A descriptors, respectively, than for the totally organic biphasic systems for compounds with a reliable value for the E descriptor. The preferred system for descriptor assignments utilizes both totally organic biphasic systems (heptane-1,1,1-trifluoroethanol, isopentyl ether-propylene carbonate, isopentyl ether-ethanolamine, heptane-ethylene glycol, heptane-formamide, and 1,2-dichloroethane-ethylene glycol) and aqueous biphasic systems (octanol-water, cyclohexane-water) with the possible substitution of some systems with alternative systems of similar selectivity. For 55 varied compounds this combination of eight organic and aqueous biphasic systems resulted in an AAD of approximately 0.03, 0.02, and 0.02 for the S, A, and B descriptors compared to the best estimate of the true descriptor value. For 30 compounds solid at 20 °C the AAD for the E descriptor of 0.11 is poorly assigned. The relative average absolute deviation in percent (RAAD) corresponds to 9.7 %, 3.1 %. 4.0 % and 8.3 % for E, S, A, and B, respectively, for the eight biphasic systems. Liquid-liquid partition is compared to reversed-phase liquid and gas chromatography as a standalone technique for descriptor assignments.

Determination of descriptors for the principal flavor compounds of the cinnamons of commerce by gas chromatography and liquid-liquid partition

Descriptors for fourteen semivolatile organic compounds associated with the authenticity, botanical origin, and flavor potential of the cinnamons of commerce were determined using the Solver method and experimental retention factors determined by gas chromatography at several temperatures on a minimum of seven selectivity-selected, open-tubular columns and liquid-liquid partition constants in up to twenty totally organic biphasic systems. The six descriptors that encode the solvation properties of the compounds were used to predict water-gas, octanol-gas, and octanol-water partition constants commonly employed to assess environmental distribution properties. For octanol-water partition constants, log KOW, the predicted partition constants exhibited an average absolute deviation of 0.12 for log KOW experimental - log KOW predicted (n = 14). Soil-water, soil-air, urban aerosol-air, skin-water permeation, and non-specific toxicity to the fathead minnow were predicted for the same compounds to assess their potential environmental impact. The product terms of the solvation parameter model provide a useful insight into the contribution of individual intermolecular interactions to the distribution properties of the cinnamon compounds and their environmental impact.

Revised descriptors for polycyclic aromatic and related hydrocarbons for the prediction of environmental properties using the solvation parameter model

Revised descriptors for twenty-five polycyclic aromatic and related hydrocarbons (PAHs) forming a component of the Wayne State University (WSU) descriptor database are provided for use with the solvation parameter model. The descriptors are determined by the Solver method using experimental data for calibrated gas-liquid and reversed-phase liquid chromatographic retention factors and liquid-liquid partition constants in totally organic biphasic systems. The characteristic solvation properties of the PAHs are accounted for mainly by the additional dispersion interactions (E descriptor) and dipole-type interactions (S descriptor) resulting from the availability of easily polarizable electrons that complement typical dispersion interactions for saturated hydrocarbons. The descriptors afford acceptable prediction of the water-air partition constant (average absolute deviation AAD = 0.17, n = 22), octanol-air partition constant (AAD = 0.12, n = 20), and water-octanol partition constant (AAD = 0.10, n = 23). A two-parameter model containing only the V and B descriptors provides an unbiased prediction of aqueous solubility for the PAHs with an AAD = 0.26 (n = 22). The descriptors estimated by convenient chromatographic and partition constant measurements are demonstrated to be a viable alternative to the experimental determination of environmental properties otherwise only available by tedious, expensive, and low data throughput experimental techniques.

The effect of the assigned descriptors for phthalate esters on the characterization of their separation properties using the solvation parameter model

Revised descriptors are determined for fifteen phthalate esters for use in the solvation parameter model and form part of the Wayne State University (WSU) compound descriptor database. For thirteen phthalate esters a comparison is made with the same compounds in the Abraham descriptor database. Gas chromatographic retention factors on poly(methyloctylsiloxane), SPB-Octyl, and poly(cyanopropylphenyldimethylsiloxane), DB-225, stationary phases are used to facilitate an assessment of the contribution of cavity formation and dispersion interactions, L descriptor, and dipole-type interactions, S descriptor, to the experimental retention factors (log k) for the phthalate esters with minimum interference from competing intermolecular interactions. The results indicate a systematic overprediction of the cavity and dispersion interaction term and underprediction of dipole-type interactions for the Abraham descriptors compared with the WSU descriptors for the phthalate esters. The average absolute deviation (AAD) for 13 phthalate esters on SPB-Octyl is 0.039 (WSU descriptors) compared with 0.252 (Abraham descriptors) and for 9 phthalate esters on DB-225 0.030 (WSU descriptors) compared with 0.167 (Abraham descriptors). The results for dipole-type interactions are confirmed and extended to include the hydrogen-bond basicity of the phthalate esters, B descriptor, by evaluation of partition constants in aqueous biphasic systems and the n-heptane-2,2,2-trifluoroethanol biphasic system. Differences in the contribution of the hydrogen-bond basicity of the phthalate esters to the experimental partition constants are largely random with respect to database selection but important for the accurate prediction of the partition constants. The AAD for the partition constant for 15 phthalate esters is 0.063 (WSU descriptors) compared with 0.320 (Abraham descriptors) for the heptane-2,2,2-trifluoroethanol biphasic system and 0.13 (WSU descriptors) compared with 0.25 (Abraham descriptors) for 9 phthalate esters in the octanol-water biphasic system. The WSU descriptors for the phthalate esters exhibit a better fit with the experimental data for separation systems and are free of the extreme values predicted for the Abraham descriptors for several phthalate esters.

The effect of descriptor database selection on the physicochemical characterization and prediction of water-air, octanol-air and octanol-water partition constants using the solvation parameter model

The distribution of neutral compounds in biphasic separation systems can be described by the solvation parameter model using six solute properties, or descriptors. These descriptors (McGowan's characteristic volume, excess molar refraction, dipolarity/polarizability, hydrogen-bond acidity and basicity, and the gas-liquid partition constant on n-hexadecane at 298.15 K) are curated in two publicly accessible databases for hundreds (WSU compound descriptor database) or thousands (Abraham compound descriptor database). These databases were developed independently using different approaches resulting in descriptor values that vary for many compounds. Previously, it was shown that the two descriptor databases are not interchangeable, and the WSU descriptor database consistently demonstrated improved model performance for chromatographic systems where the uncertainty in the dependent variable was minimized by suitable quality control and calibration procedures. In this report we wish to evaluate whether the same conclusions are true for models with a dependent variable containing significant measurement uncertainty. To evaluate this hypothesis, we assembled databases for water-air, octanol-air, and octanol-water partition constants reported by multiple laboratories using various measurement methods. It was found that database selection has little effect on model quality or model predictive capability but significantly affects the assignment of the contribution of individual intermolecular interactions to the dependent variable. The latter information is database specific, and a quantitative comparison of system constants should be restricted to models using the same compound descriptor database.

Sample preparation for planar chromatography

High-performance thin-layer chromatography has favorable properties for high-throughput separations with a high matrix tolerance. Sample preparation, however, is sometimes required to control specific matrix interferences and to enhance the detectability of target compounds. Trends in contemporary applications have shifted from absorbance and fluorescence detection to methods employing bioassays and mass spectrometry. Traditional methods (shake-flask, heat at reflux, Soxhlet, and hydrodistillation) are being challenged by automated instrumental approaches (ultrasound-assisted and microwave-assisted solvent extraction, pressurized liquid extraction, and supercritical fluid extraction) and the quick, easy cheap, efficient, rugged, and safe extraction method for faster and streamlined sample processing. Liquid-liquid extraction remains the most widely used approach for sample clean-up with increasing competition from solid-phase extraction. On-layer sample, clean-up by planar solid-phase extraction is increasingly used for complex samples and in combination with heart-cut multimodal systems. The automated spray-on sample applicator, the elution head interface, biological detection of target and non-target compounds, and straightforward mass spectrometric detection are highlighted as the main factors directing current interest toward faster and simpler sample workflows, analysis of more complex samples, and the determination of minor contaminants requiring high concentration factors.

Selectivity evaluation of extraction systems

Extraction is the most common sample preparation technique prior to chromatographic analysis for samples which are too complex, too dilute, or contain matrix components incompatible with the further use of the separation system or interfere in the detection step. The most important extraction techniques are biphasic systems involving the transfer of target compounds from the sample to a different phase ideally accompanied by no more than a tolerable burden of co-extracted matrix compounds. The solvation parameter model affords a general framework to characterize biphasic extraction systems in terms of their relative capability for solute-phase intermolecular interactions (dispersion, dipole-type, hydrogen bonding) and within phase solvent-solvent interactions for cavity formation (cohesion). The approach is general and allows the comparison of liquid and solid extraction phases using the same terms and is used to explain the features important for the selective enrichment of target compounds by a specific extraction phase using solvent extraction, liquid-liquid extraction, and solid-phase extraction for samples in a gas, liquid, or solid phase. Hierarchical cluster analysis with the system constants of the solvation parameter model as variables facilitates the selection of solvents for extraction, the identification of liquid-liquid distribution systems with non-redundant selectivity, and evaluation of different approaches using liquids and solids for the isolation of target compounds from different matrices.

The influence of descriptor database selection on the solvation parameter model for separation processes

The distribution of neutral compounds in biphasic separation systems can be described by the solvation parameter model using six solute properties, or descriptors. These descriptors characterize the size (McGowan's characteristic volume), V, excess molar refraction, E, dipolarity/polarizability, S, hydrogen-bond acidity and basicity, A and B, and the gas-liquid partition constant on n-hexadecane at 298.15 K, L. McGowan's characteristic volume and the excess molar refraction for liquids are available by calculation (E requires and experimental refractive index). The other descriptors and excess molar refraction for solids are experimental quantities and subject to greater variation or are estimated using computational or empirical models. Solute descriptors for several thousand compounds are available in the Abraham descriptor database and for several hundred compounds in the WSU descriptor database. These publicly accessible databases were developed independently using different approaches and for many compounds provide different descriptor values. In this report we evaluate the effect of mixing descriptors from the two databases on modeling chromatographic retention factors and liquid-liquid partition constants. It is shown that the two descriptor databases are not interchangeable. The WSU descriptor database consistently demonstrates improved model quality as determined by statistical parameters. Model system constants exhibit a general dependence on database selection with an approximately linear trend as a function of the fraction of compounds assigned descriptors from either database. There is no general model performance advantage to using mixed descriptor datasets and no real cause for concern for relatively large datasets containing < 15 % of compounds with descriptors assigned from the other database. For small datasets, descriptor quality is an important variable for adequate model performance.

Recent advances for estimating environmental properties for small molecules from chromatographic measurements and the solvation parameter model

The transfer of neutral compounds between immiscible phases in chromatographic or environmental systems can be described by six solute properties (solute descriptors) using the solvation parameter model. The solute descriptors are size (McGowan's characteristic volume), V, excess molar refraction, E, dipolarity/polarizability, S, hydrogen-bond acidity and basicity, A and B, and the gas-liquid partition constant on n-hexadecane at 298.15 K, L. V and E for liquids are accessible by calculation but the other descriptors and E for solids are determined experimentally by chromatographic, liquid-liquid partition, and solubility measurements. These solute descriptors are available for several thousand compounds in the Abraham solute descriptor databases and for several hundred compounds in the WSU experimental solute descriptor database. In the first part of this review, we highlight features important in defining each descriptor, their experimental determination, compare descriptor quality for the two organized descriptor databases, and methods for estimating Abraham solute descriptors. In the second part we focus on recent applications of the solvation parameter model to characterize environmental systems and its use for the identification of surrogate chromatographic models for estimating environmental properties.

Solvation parameter model: Tutorial on its application to separation systems for neutral compounds

The solvation parameter model affords a useful tool to model distribution properties of neutral compounds in biphasic separation systems. Common applications include column characterization and method development in gas chromatography; reversed-phase, micellar and hydrophilic interaction liquid chromatography; supercritical fluid chromatography; and micellar electrokinetic chromatography. The characterization of the distribution properties of liquid-liquid partition systems is another major application of this model. This tutorial is aimed at establishing good practices for the application of the model to separation systems. Suitable experimental protocols to determine system constants by multiple linear regression analysis and descriptors by the Solver method are presented; statistical tools to evaluate model quality are discussed; and model-specific data analysis tools based on system maps and correlation diagrams are described.

Acetonitrile-Hexane Extraction Route to Pure Sulfonium Salts

A rapid, simple procedure is described for synthesizing trialkyl, dialkylaryl, and alkyldiaryl sulfonium salts that features a selective extraction procedure to access analytically pure sulfonium salts. Alkylation of dialkylsulfides, alkylarylsulfides, and diarylsulfides followed by partitioning between acetonitrile and hexanes efficiently separates nonpolar reactants and byproducts, the usual impurities, to afford analytically pure crystalline and noncrystalline sulfonium salts. The method is efficient, general, and particularly well suited for the preparation of oily sulfonium salts that are otherwise extremely difficult to purify.

Ionic Liquid-Liquid Chromatography: A New General Purpose Separation Methodology

Ionic liquids can form biphasic solvent systems with many organic solvents and water, and these solvent systems can be used in liquid-liquid separations and countercurrent chromatography. The wide range of ionic liquids that can by synthesised, with specifically tailored properties, represents a new philosophy for the separation of organic, inorganic and bio-based materials. A customised countercurrent chromatograph has been designed and constructed specifically to allow the more viscous character of ionic liquid-based solvent systems to be used in a wide variety of separations (including transition metal salts, arenes, alkenes, alkanes, bio-oils and sugars).