Metal-organic frameworks as solid-phase microextraction adsorbents for the determination of triacetone triperoxide by gas chromatography-mass spectrometry

Triacetone triperoxide (TATP) is a high-power explosive which is often used by criminals. The detection of TATP is of great significance for solving the explosion cases. However, the preconcentration and analysis of trace levels of TATP still pose challenges for analytical researchers. In this study, metal-organic frameworks (MOFs), including IRMOF-8, MOF-5, UIO-66, ZIF-8, and MIL-101(Cr), were immobilized on a stainless steel wire using a physical adhesive method as a solid-phase microextraction (SPME) fiber coating. The prepared fibers with a controllable thickness were used for the extraction of TATP followed by gas chromatography-mass spectrometry (GC-MS) analysis. Under the identical experimental conditions, the IRMOF-8-coated fiber exhibited higher extraction efficiency for TATP than the other fibers. The IRMOF-8-coated fiber was then characterized using scanning electron microscopy and thermogravimetric analysis. The results indicated that the IRMOF-8-coated fiber not only had good thermal and chemical stabilities but also afforded a high TATP extraction efficiency. Under the same extraction conditions, the extraction efficiency of the IRMOF-8-coated fiber was 2-8 times higher than those of commercial fibers. The limit of detection was 13 ng/mL, and linearity was observed in the range of 50-5000 ng/mL with a correlation coefficient greater than 0.998. The intraday repeatability (n = 6), interday repeatability (n = 3), and fiber-to-fiber reproducibility (n = 3), were 4.1 %, 4.8 %, and 8.0 %, respectively. The recoveries of TATP from the simulated tap water and soil samples were 87.32-90.57 % and 88.76-100.93 %, respectively, with relative standard deviations lower than 11.11 % (n = 3). The above method was successfully applied for the detection of TATP transferred from a finger to a paper surface, demonstrating its good application prospects in the analysis of trace TATP.

Zn-based metal organic framework-covalent organic framework composites for trace lead extraction and fluorescence detection of TNP

A novel dual functional composite (MOF_L-TpBD) was prepared through solvothermal methods, with excellent Pb²⁺ ions separation and stable 2,4,6-Trinitrophenol (TNP) fluorescence detection performance. MOF_L-TpBD was characterized by FTIR, XRD, XPS, SEM and TGA et al. The prepared material was used to extract Pb²⁺ ions, with an adsorption capacity of 21.74 mg g^-1 calculated by Langmuir isotherm model. The limit of detection was 0.32 μg L^-1, along with a linear range from 0.7 to 12 μg L^-1 and a precision of 5.4% (1 μg L^-1, n = 9), respectively, where MOF_L-TpBD was adopted as adsorbent for Pb²⁺ ions preconcentration. The practical samples and reference water sample were measured by the provided method, with the satisfactory recoveries (91-110%) and reliable analytical results. MOF_L-TpBD was capable of fluorescent sensing of TNP, with a linear range from 0.01 to 1 mM and a limit of detection of 3.52 μM, respectively, and a precision of 3.29% was obtained (0.2 mM, n = 11). Meanwhile, the recoveries ranged from 91% to 108% in analysis of TNP for the practical samples. The designed material provided a potential candidate material for the detection of heavy metal ions and explosives in environmental water samples.

Sample preparation with solid phase microextraction and exhaustive extraction approaches: Comparison for challenging cases

In chemical analysis, sample preparation is frequently considered the bottleneck of the entire analytical method. The success of the final method strongly depends on understanding the entire process of analysis of a particular type of analyte in a sample, namely: the physicochemical properties of the analytes (solubility, volatility, polarity etc.), the environmental conditions, and the matrix components of the sample. Various sample preparation strategies have been developed based on exhaustive or non-exhaustive extraction of analytes from matrices. Undoubtedly, amongst all sample preparation approaches, liquid extraction, including liquid-liquid (LLE) and solid phase extraction (SPE), are the most well-known, widely used, and commonly accepted methods by many international organizations and accredited laboratories. Both methods are well documented and there are many well defined procedures, which make them, at first sight, the methods of choice. However, many challenging tasks, such as complex matrix applications, on-site and in vivo applications, and determination of matrix-bound and free concentrations of analytes, are not easily attainable with these classical approaches for sample preparation. In the last two decades, the introduction of solid phase microextraction (SPME) has brought significant progress in the sample preparation area by facilitating on-site and in vivo applications, time weighted average (TWA) and instantaneous concentration determinations. Recently introduced matrix compatible coatings for SPME facilitate direct extraction from complex matrices and fill the gap in direct sampling from challenging matrices. Following introduction of SPME, numerous other microextraction approaches evolved to address limitations of the above mentioned techniques. There is not a single method that can be considered as a universal solution for sample preparation. This review aims to show the main advantages and limitations of the above mentioned sample preparation approaches and the applicability and capability of each technique for challenging cases such as complex matrices, on-site applications and automation.