A new molecularly imprinted polymer for selective extraction and pre‐concentration of guaifenesin in different samples: Adsorption studies and kinetic modeling

Detection and adsorption of florfenicol in milk using bifunctional carbon dot-doped molecularly imprinted polymers

Detection of florfenicol (FF) residues in animal-derived foods, as one of the most widely used antibiotics, is critically important to food safety. The fluorescent molecularly imprinted polymer (MIP) was synthesized by surface-initiated atom transfer radical polymerization technique with poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate) microspheres, 4-vinylpyridine, ethylene glycol dimethacrylate, and FF as the matrix, functional monomer, crosslinker, and template molecule, respectively. Meanwhile, N-S co-doped carbon dot (CD) was synthesized with triammonium citrate and thiourea as precursors under microwave irradiation at 400 W for 2.5 min and then integrated into FF-MIP to obtain CD@FF-MIP. For comparison, non-imprinted polymer (NIP) without FF was also prepared. The adsorption capacity of CD@FF-MIP to FF reached 53.1 mg g-1, which was higher than that of FF-MIP (34.7 mg g-1), whereas the adsorption capacity of NIP was only 17.3 mg g-1. The adsorption equilibrium of three materials was reached within 50 min. Particularly, CD@FF-MIP exhibited an excellent fluorescence quenching response to FF in the concentration range of 3-50 µmol L-1. As a result, CD@FF-MIP was successfully utilized to extract FF in milk samples, which were analyzed by high-performance liquid chromatography. The standard recoveries were 95.8%-98.2%, and the relative standard deviation was 1.6%-4.2%. The method showed the advantages of simple operation, high sensitivity, excellent selectivity, and low cost, and also demonstrated a great application prospect in food detection.

Recent advances and applications of molecularly imprinted polymers in solid-phase extraction for real sample analysis

Sample pretreatment is essential for the analysis of complicated real samples due to their complex matrices and low analyte concentrations. Among all sample pretreatment methods, solid-phase extraction is arguably the most frequently used one. However, the majority of available solid-phase extraction adsorbents suffer from limited selectivity. Molecularly imprinted polymers are a type of tailor-made artificial antibodies and receptors with specific recognition sites for target molecules. Using molecularly imprinted polymers instead of conventional adsorbents can greatly improve the selectivity of solid-phase extraction, and therefore molecularly imprinted polymer-based solid-phase extraction has been widely applied to separation, clean up and/or preconcentration of target analytes in various kinds of real samples. In this article, after a brief introduction, the recent developments and applications of molecularly imprinted polymer-based solid-phase extraction for determination of different analytes in complicated real samples during the 2015-2020 are reviewed systematically, including the solid-phase extraction modes, molecularly imprinted adsorbent types and their preparations, and the practical applications of solid-phase extraction to various real samples (environmental, food, biological, and pharmaceutical samples). Finally, the challenges and opportunities of using molecularly imprinted polymer-based solid-phase extraction for real sample analysis are discussed.

Recognition and selective extraction of poly-γ-glutamic acid based on molecular imprinting technology

Poly-γ-glutamic acid (γ-PGA) is one of the few bacterial polymers in nature with high added value of biodegradability. Especially, the traditional method of extracting γ-PGA is organic solvent extraction, etc., which has the disadvantages of low extraction rate and serious environmental pollution. With the expansion of γ-PGA industrial fermentation, an efficient and environmentally friendly method is required to be adopted. In this contribution, we report a novel method of separation of γ-PGA from fermentation broth based on molecular imprinting technology. The molecular imprinted polymer (MIP) was synthesized from chitosan (CS) and glutaraldehyde in the presence of γ-PGA. A nonimprinted polymer (NIP) was also synthesized by the same procedure in the absence of γ-PGA. The chemical structures and morphological structures of both MIP and NIP were examined by FTIR spectroscopy and scanning electron microscopy. The adsorption isotherms showed that the maximum adsorption capacity of MIP was 137.85 mg/g. The maximum adsorption capacity in the adsorption of NIP was 68.92 mg/g, which indicates that MIP shows specific selectivity for γ-PGA. A high saturated absorption capacity (Qmax=140.90 mg/g) was calculated from Freundlich isotherm equation. The imprinting factor of MIP was 4.76, indicating that MIP possess good recognition ability and selectivity for γ-PGA. The adsorption capacity decreased slightly (17.0%), which suggests the satisfactory reusability of γ-PGA after 5 cycles of reuse. Our study indicates that molecularly imprinted polymers present development prospects in the effective and selective separation of γ-PGA from fermentation broth compared with organic solvent precipitation.