Mesoporous silica hybridized by ordered mesoporous carbon for in-tube solid-phase microextraction

Nanoporous carbon fiber derived from Cu-BDC metal organic framework @pencil graphite as a sorbent for solid phase microextraction of acetamiprid and imidacloprid

Solid-phase microextraction (SPME) is a sample pretreatment technique for enrichment of trace level of compounds from complex matrices. The fiber coating, as an extraction phase, is the significant part of SPME, which specifying the analytical performance of the developed SPME. In this study, a novel in situ fabricated Cu@porous carbon fiber that derived from copper benzene-1,4-dicarboxylate framework@pencil graphite (Cu-BDC MOF@PG) fiber was prepared as a SPME fiber. The Cu-BDC MOF was electrodeposited on the surface of pencil graphite. The Cu@porous carbon fiber with nanoporous structure was constructed by the direct carbonization of the electrosynthesized fiber. The Cu@porous carbon fiber showed high analytical performance for direct immersion SPME (DI-SPME) of acetamiprid and imidacloprid in fruit and vegetable samples. The SPME method was coupled by high-performance liquid chromatography-ultraviolet detection (SPME-HPLC-UV) for determination of the analytes. Under the optimized condition, good linear ranges (1-500 μg L-1 and 0.5-200 μg L-1) and acceptable limits of detection (LODs = 0.30 and 0.15 μg L-1), appropriate spiking recoveries in the range 87-109.0% were attained for acetamiprid and imidacloprid, respectively. Intra- and inter-day relative standard deviations were found within the ranges of 2.35-3.46% and 3.30-3.70%, respectively. These results signify promising potential of the in situ fabricated porous carbon fiber for SPME applications. Considering that most of the pencil graphite is made of carbon, after the carbonization of the Cu-BDC MOF@PG fiber, a unified porous carbon fiber is obtained. Compared to other reported procedures, in situ direct carbonization of Cu-BDC MOF@PG fiber was a one-step and straightforward method to fabricate carbon fiber.

The Structure of Ordered Mesoporous Materials Synthesized from Aluminum Phyllosilicate Clay (Bentonite)

This paper reports the synthesis and structural analysis of mesoporous silica materials with the use of aluminum phyllosilicate clay (bentonite) as an alternative silica source. In the proposed synthesis, bentonite, as natural aluminosilicate, was used instead of commercially available and quite expensive tetraethyl orthosilicate (TEOS) silica source. The objective of the research study was to determine the effect of aluminum loading in the mesoporous silica body for ordering structure, porosity, and potential sorption capacity to thorium ions. The unique direction developed in this procedure is focused on preparing advanced materials from natural sources with their own desired functionality and general availability. The applied procedure based on the classic, one-step synthesis of SBA-15 silicates was modified by gradually increasing the bentonite amount with simultaneous reduction of the TEOS content. The structural and morphological characterization, as well as evaluation of the porous structure of the obtained materials, was performed using powder wide-angle X-ray diffraction (XRD), small-angle scattering (SAXS), transmission and scanning electron microscopy (TEM, SEM), low-temperature nitrogen adsorption–desorption methods and potentiometric titration. The new, cost-effective composites for the removal of Th(IV) ions are proposed. The synergistic effect of expanding the porous surface using bentonite as a silica precursor and the presence of thorium-binding groups (such as Al2O3) is indicated.

Mesostructured Silicas as Cation-Exchange Sorbents in Packed or Dispersive Solid Phase Extraction for the Determination of Tropane Alkaloids in Culinary Aromatics Herbs by HPLC-MS/MS

In this work, Hexagonal Mesoporous Silica (HMS) and Santa Barbara Amorphous-15 (SBA-15) mesostructured silicas were synthesized and functionalized with sulfonic acid groups. The materials (HMS-SO3− and SBA-15-SO3−) were evaluated as strong cation exchange sorbents for sample extract clean-up, by solid phase extraction (SPE) and dispersive solid phase extraction, to determine atropine (At) and scopolamine (Sc) in commercial culinary aromatic herbs. Under optimized conditions, 0.25 g of sample was subject to solid−liquid extraction with acidified water (pH 1.0), and good recovery percentages were achieved for At and Sc using 75 mg of HMS-SO3− in SPE as the clean-up stage, prior to their determination by HPLC-MS/MS. The proposed method was validated in a thyme sample showing recoveries in the range of 70−92%, good linearity (R2 > 0.999), adequate precision (RSD ≤ 14%) and low limits (MDL 0.8−2.2 µg/kg and MQL 2.6−7.2 µg/kg for both analytes). Sixteen aromatic herbs samples (dried thyme, basil and coriander leaves) were analysed and At was found in fourteen samples over an interval of <5−42 μg/kg, whereas Sc was found in three of the sixteen samples studied (between <5−34 μg/kg). The amount of At and Sc found in some analysed samples confirms the importance of setting maximum levels of At and Sc in culinary aromatic herbs.

Research on Adsorption and Desorption Performance of Gas-Phase Naphthalene on Hydrophobic Modified FDU-15

Naphthalene (NAP) is a typical gaseous polycyclic aromatic hydrocarbons (PAHs) pollutant that displays toxicological effects on biosystems. Ordered mesoporous carbon has relatively adequate adsorption capacity; however, the attached hydrophilic functional groups were proven to affect the adsorption performance in the presence of moisture. In this paper, trimethylchlorosilane (TMCS) is used to carry out the hydrophobic modification of ordered mesoporous carbon FDU-15, and the adsorption and desorption properties of FDU-15 were studied. Furthermore, the adsorption isotherms of naphthalene on FDU-15 and modified FDU-15 were fitted by L-F equation, and the kinetic parameters of desorption of naphthalene on modified FDU-15 were analyzed based on the method of temperature programming desorption (TPD). The results showed that the micropore volume and specific surface area of FDU-15 were significantly increased after hydrophobically modified by TMCS, and the polar functional groups of the hydrophobically modified FDU-15 were significantly reduced. Furthermore, the adsorption of naphthalene by FDU-15 before and after modification conformed to the L-F equation (R2 > 99%), and the adsorption of naphthalene by modified FDU-5 at low concentration was significantly improved due to the increase of micropores. Based on desorption kinetic performance study of modified FDU-15, it can be seen that the adsorption kinetic characteristics of naphthalene on the modified FDU-15 conform to the mechanical function of the JMA equation. When the mass ratio of TMCs to FDU-15 is 1:10 in the modification process, the pore structure and surface hydrophobicity of the modified FDU-15 reach an excellent balance. At this time, the adsorbent had the optimum desorption performance under experimental conditions, and the desorption activation energy was decreased from 60.98 kJ/mol of FDU-15 to 50.28 kJ/mol.