Investigation of Thermoresponsive Nano-Confined Polymer Brushes by AFM-Based Force Spectroscopy

Eco-Friendly Electroless Template Synthesis of Cu-Based Composite Track-Etched Membranes for Sorption Removal of Lead(II) Ions

This paper reports the synthesis of composite track-etched membranes (TeMs) modified with electrolessly deposited copper microtubules using copper deposition baths based on environmentally friendly and non-toxic reducing agents (ascorbic acid (Asc), glyoxylic acid (Gly), and dimethylamine borane (DMAB)), and comparative testing of their lead(II) ion removal capacity via batch adsorption experiments. The structure and composition of the composites were investigated by X-ray diffraction technique and scanning electron and atomic force microscopies. The optimal conditions for copper electroless plating were determined. The adsorption kinetics followed a pseudo-second-order kinetic model, which indicates that adsorption is controlled by the chemisorption process. A comparative study was conducted on the applicability of the Langmuir, Freundlich, and Dubinin-Radushkevich adsorption models to define the equilibrium isotherms and the isotherm constants for the prepared composite TeMs. Based on the regression coefficients R², it has been shown that the Freundlich model better describes the experimental data of the composite TeMs on the adsorption of lead(II) ions.

AFM Characterization of Track-Etched Membranes: Pores Parameters Distribution and Disorder Factor

The structural characteristics of polymer track-etched membranes (TM) were obtained by atomic force microscopy (AFM) for a set of samples (polypropylene, polycarbonate, polyethylene terephthalate, with average pore diameters ~183, 375, and 1430 nm, respectively). The analysis of AFM experimental data was performed by using a specially developed technique for computer analysis of AFM images. The method allows one to obtain such parameters of TM as distribution of pore diameters, distribution of the minimum distances between the nearest pores, pore surface density, as well as to identify defective pores. Spatial inhomogeneities in the distribution of pore parameters were revealed. No anisotropy (some specific selected direction) was found in the surface distribution of the pores in the samples under study.

Layer-by-layer assembly in nanochannels: assembly mechanism and applications

Layer-by-layer (LbL) assembly is a versatile technology to construct multifunctional nanomaterials using various supporting substrates, enabled by the large selection freedom of building materials and diversity of possible driving forces. The fine regulation over the film thickness and structure provides an elegant way to tune the physical/chemical properties by mild assembly conditions (e.g. pH, ion strength). In this review, we focus on LbL in nanochannels, which exhibit a different growth mechanism compared to "open", convex substrates. The assembly mechanism in nanochannels is discussed in detail, followed by the summary of applications of LbL assemblies liberated from nanochannel templates which can be used as nanoreactors, drug carriers and transporting channels across cell membranes. For fluidic applications, robust membrane substrates are required to keep in place nanotube arrays for membrane-based separation, purification, biosensing and energy harvesting, which are also discussed. The good compatibility of LbL with crossover technologies from other fields allows researchers to further extend this technology to a broader range of research fields, which is expected to result in an increased number of applications of LbL technology in the future.

Poly(diethylene glycol methylether methacrylate) Brush-Functionalized Anodic Alumina Nanopores: Curvature-Dependent Polymerization Kinetics and Nanopore Filling

We report on the synthesis and characterization of poly(diethylene glycol methylether methacrylate) (PDEGMA) brushes by surface-initiated atom transfer radical polymerization inside ordered cylindrical nanopores of anodic aluminum oxide with different pore radii between 20 and 185 nm. In particular, the dependence of polymerization kinetics and the degree of pore filling on the interfacial curvature were analyzed. On the basis of field emission scanning electron microscopy data and thermal gravimetric analysis (TGA), it was concluded that the polymerization rate was faster at the pore orifice compared to the pore interior and also as compared to the analogous reaction carried out on flat aluminum oxide substrates. The apparent steady-state polymerization rate near the orifice increased with decreasing pore size. Likewise, the overall apparent polymerization rate estimated from TGA data indicated stronger confinement for pores with increased curvature as well as increased mass transport limitations due to the blockage of the pore orifice. Only for pores with a diameter to length ratio of ∼1, PDEGMA brushes were concluded to grow uniformly with constant thickness. However, because of mass transport limitations in longer pores, incomplete pore filling was observed, which leads presumably to a PDEGMA gradient brush. This study contributes to a better understanding of polymer brush-functionalized nanopores and the impact of confinement, in which the control of polymer brush thickness together with grafting density along the nanopores is key for applications of PDEGMA brushes confined inside nanopores.

Formation and Characteristics of Lipid-Blended Block Copolymer Bilayers on a Solid Support Investigated by Quartz Crystal Microbalance and Atomic Force Microscopy

Liposomes grafted with polymer have long been used in drug delivery applications, and block copolymersomes have emerged as attractive and more robust alternatives for both drug delivery and artificial organelle applications. Hybrid membranes that could combine the respective advantages of fluid lipid and robust polymer bilayers are an attractive and enticing alternative. The properties of membranes in amphiphile vesicles are challenging to study and many applications benefit from surface-based access to the membrane. We therefore explore the self-assembly and mechanical properties of supported hybrid bilayers (SHBs) composed of polybutadiene- block-poly(ethylene oxide) block copolymers and zwitterionic phosphatidylcholine lipids on SiO₂ supports. Quartz crystal microbalance with dissipation monitoring (QCM-D) measurements show that formation of SHB on SiO₂ by vesicle fusion depends on the mass fractions of lipids and block copolymers. Atomic force microscopy was used to study the microscopic mixing of lipids in the SHB to reveal that lipid-phase separation is not observed in SHBs. Force spectroscopy was performed to extract information about thickness and mechanical properties of the hybrid membranes. SHBs are shown to combine the properties of lipid membranes and polymer brushes, and the tip force required to rupture the membrane decreases and the bilayer thickness increases as the block copolymer fraction is increased.

Control of swelling of responsive nanogels by nanoconfinement

The volume phase transition (VPT) behavior and the swelling properties of individual thermoresponsive poly(N-isopropylacrylamide) (PNIPAM)-based nanogels are investigated by in situ atomic force microscopy (AFM). Using a template-based synthesis method, cylindrical nanogels are synthesized for different polymerization times within nanopores (80 nm) of poly(ethylene terephthalate) (PET) track-etched membranes. The confinement conditions, characterized by the ratio Φ between the average chain length and the pore diameter, are varied between 0.35 and 0.8. After dissolving the membranes, the volume of individual nanogels composed of PNIPAM-g-PET diblock copolymers is numerically extracted from AFM images while varying the water temperature from 28 to 44 °C. From the measured volumes, the swelling of nanogels is investigated as a function of both the water temperature and the confinement conditions imposed during the synthesis. Contrary to the VPT, the maximum swelling of the nanogels is strongly affected by these confinement conditions. The volume of nanogels in the swollen state can reach 1.1 to 2.1 times their volume in the collapsed state for a ratio Φ of 0.8 and 0.5, respectively. These results open a new way to tune the swelling of nanogels, simply by adjusting the degree of confinement imposed during their synthesis within nanopores, which is particularly interesting for biomedical applications requiring a high degree of control over swelling properties, such as drug-delivery nanotools.