Oriented Overgrowths of Poly(l -Lactide) on Oriented Isotactic Polypropylene: A Sequence of Soft and Hard Epitaxies

Petal-like Patterning of Polylactide/Poly (Butylene Succinate) Thin Films Induced by Phase Separation

Biodegradable plastics are attracting attention as a solution to the problems caused by plastic waste. Among biodegradable plastics, polylactide (PLA) and poly (butylene succinate) (PBS) are particularly noteworthy because of their excellent biodegradability. However, the drawbacks of their mechanical properties prompts the need to compound them to achieve the desired strength. The characteristics of the interface of the composite material determine the realization of its final performance. The study of the interface and microstructure of composites is essential for the development of products from degradable polymers. The morphology evolution and microcrystal structure of spin-casted fully biodegradable (PLA/PBS) blend films were investigated using atomic force microscopy (AFM)-based nanomechanical mapping. Results show that intact blend films present an obvious phase separation, where the PBS phase is uniformly dispersed in the PLA phase in the form of pores. Furthermore, the size and number of the PBS phase have a power exponential relationship and linear relationship with PBS loading, respectively. Intriguingly, after annealing at 80 °C for 30 min, the PLA phase formed an orderly petal-like microcrystalline structure centered on the PBS phase. Moreover, the microcrystalline morphology changed from a "daisy type" to a "sunflower type" with the increased size of the PBS phase. Since the size of the PBS phase is controllable, a new method for preparing microscopic patterns using fully biodegradable polymers is proposed.

In Situ SAXS and WAXD Investigations of Polyamide 66/Reduced Graphene Oxide Nanocomposites During Uniaxial Deformation

Epitaxial crystallization between Polyamide 66 (PA66) and reduced graphene oxide (RGO) can enhance the interfacial interaction and the mechanical properties of PA66/RGO nanocomposites. In situ two-dimensional synchrotron radiation wide angle X-ray diffraction and small angle X-ray scattering were used to track the structural evolution of the PA66/RGO nanocomposites with an epitaxial crystal during uniaxial deformation. In the PA66/RGO nanocomposites, the structural evolution of non-epitaxial and epitaxial crystals could be clearly analyzed. The non-epitaxial crystal, whose crystal plane can slip, shows the rearrangement and the Brill transition during uniaxial deformation. While the PA66 chains of an epitaxial crystal are held by RGO, the crystal plane could therefore not slip. The epitaxial crystal also constrains the deformation of the amorphous phase and the crystal form transition of non-epitaxial crystals around them. With the content increase of epitaxial crystals, the constraint effect becomes more obvious. Therefore, the rigid epitaxial crystals in the PA66/RGO nanocomposites promote mechanical properties. The present findings can deepen the understanding of structural evolution during the tensile deformation of PA66/RGO nanocomposites and the influence of the epitaxial crystals on the mechanical property in semicrystalline polymers with a H-bond.

Epitaxial Crystallization of Poly(ε-caprolactone) on Reduced Graphene Oxide at a Low Shear Rate by In Situ SAXS/WAXD Methods

The interfacial interaction between polymers and reinforcements has a positive effect on the properties of polymer nanocomposites, and a further study on the evolution of this interfacial interaction under a shear field is conducive to reasonable regulation of the properties of polymer nanocomposites. For this purpose, epitaxial crystallization of poly(ε-caprolactone) (PCL) on reduced graphene oxide (RGO) is investigated by shearing at the shear rate of 3 s-1 by in situ synchrotron radiation. In situ two-dimensional small-angle X-ray scattering (2D SAXS) results suggest that the imposed shear field promotes the orientation of the polymer chains, resulting in the formation of a large periodic structure of PCL on the RGO surface. In addition, higher shear temperatures facilitate the conformational adjustment of the PCL molecular chain on RGO at the shear rate of 3 s-1, resulting in the formation of thicker lamellae. In situ two-dimensional wide-angle X-ray diffraction (2D WAXD) results show that shear enhances the crystallinity of the PCL/RGO nanocomposite and promotes the oriented growth of epitaxial and bulk crystals. The current findings can improve the understanding of the structural evolution behavior of PCL/RGO nanocomposites after shear and especially enhance dramatically our understanding of the underlying mechanism of influence of shear on interfacial epitaxial crystallization in polymer/graphene nanocomposite systems.

Orientation of Poly(ε-caprolactone) in Its Poly(vinyl chloride) Blends Crystallized under Strain: The Role of Strain Rate

The blends of high and low molecular weights poly(ε-caprolactone) (PCL) with poly(vinyl chloride (PVC) were prepared. The samples before and after the crystallization of PCL were uniaxially stretched to different draw ratios. The orientation features of PCL in a stretched crystalline PCL/PVC blend and crystallized from the amorphous PCL/PVC blends under varied strains were studied by wide-angle X-ray diffraction (WAXD) diffraction. It was found that a uniaxial stretching of crystalline PCL/PVC blend with high molecular weight PCL results in the c-axis orientation along the stretching direction, as is usually done for the PCL bulk sample. For the stretched amorphous PCL/PVC blend samples, the crystallization of high molecular weight PCL in the blends under a draw ratio of λ = 3 with a strain rate of 6 mm/min leads to a ring-fiber orientation. In the samples with draw ratios of λ = 4 and 5, the uniaxial orientation of a-, b-, and c-axes along the strain direction coexist after crystallization of high molecular weight PCL. With a draw ratio of λ = 6, mainly the b-axis orientation of high molecular weight PCL is identified. For the low molecular weight PCL, on the contrary, the ring-fiber and a-axis orientations coexist under a draw ratio of λ = 3. The a-axis orientation decreases with the increase of draw ratio. When the λ reaches 5, only a poorly oriented ring-fiber pattern has been recognized. These results are different from the similar samples stretched at a higher strain rate as reported in the literatures and demonstrate the important role of strain rate on the crystallization behavior of PCL in its blend with PVC under strain.