Side-chain Substituents on Benzotriazole-based Polymer Acceptors Affecting the Performance of All-polymer Solar Cells

An Investigation of the Inverted Structure of a PBDB:T/PZT:C1-Based Polymer Solar Cell

Based on experimental results, this theoretical study presents a new approach for investigating polymers' solar cells. P-type PZT:C1 and N-type PBDB:T were used to construct a blend for use as a photoactive layer for the proposed all-polymer solar cell. Initially, an architecture of an ITO/PEDOT:PSS/PBDB:T/PZT:C1/PFN-Br/Ag all-polymer solar device calibrated with experimental results achieved a PCE of 14.91%. A novel inverted architecture of the same solar device, proposed for the first time in this paper, achieved a superior PCE of 19.92%. Furthermore, the optimization of the doping of the transport layers is proposed in this paper. Moreover, the defect density and the thickness of the polymer are studied, and a PCE of 22.67% was achieved by the optimized cell, which is one of the highest PCEs of polymer solar devices. Finally, the optimized polymer solar cell showed good stability amidst temperature variations. This theoretical study sheds light on the inverted structure of all-polymer solar devices.

Device Modeling of Efficient PBDB-T:PZT-Based All-Polymer Solar Cell: Role of Band Alignment

In this study, we present some design suggestions for all-polymer solar cells by utilizing device simulation. The polymer solar cell under investigation is formed by a photoactive film of a blend comprising PBDB-T as a polymer donor and PZT as a polymerized small molecule acceptor. The initial cell is based on a fabricated cell whose structure is ITO/PEDOT:PSS/PBDB-T:PZT/PFN-Br/Ag, which has a power conversion efficiency (PCE) of about 14.9%. A calibration procedure is then performed by comparing the simulation results with experimental data to confirm the simulation models, and the material parameters, implemented in the SCAPS (Solar Cell Capacitance Simulator) simulator. To boost the open circuit voltage, we investigate a group of hole transport layer (HTL) materials. An HTL of CuI or P3HT, that may replace the PEDOT:PSS, results in a PCE of higher than 20%. However, this enhanced efficiency results in a minor S-shape curve in the current density-voltage (J-V) characteristic. So, to suppress the possibility of the appearance of an S-curve, we propose a double HTL structure, for which the simulation shows a higher PCE with a suppressed kink phenomenon due to the proper band alignment. Moreover, the designed cell is investigated when subjected to a low light intensity, and the cell shows a good performance, signifying the cell's suitability for indoor applications. The results of this simulation study can add to the potential development of highly efficient all-polymer solar cells.

Three Isomeric Non-Fullerene Acceptors Comprising a Mono-Brominated End-Group for Efficient Organic Solar Cells

Non-fullerene acceptors (NFAs) carrying a 1,1-dicyanomethylene-3-indanone (IC) end-group are the most powerful ones to boost the power conversion efficiency of organic solar cells (OSCs). However, the well-known Knoevenagel condensation of the mono-halogenated IC end-group will result in an NFA isomeric effect, a chemical issue that needs to be addressed. Herein, facile preparations and separations of three well-defined mono-brominated isomers BTzIC-2Br-δ, BTzIC-2Br-γ, and BTzIC-2Br-δγ via column chromatography with a well-chosen mixing solvent were demonstrated for Knoevenagel condensation, and their structures were verified by NMR spectra and matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF) mass spectra. It is the first time that an asymmetric isomer BTzIC-2Br-δγ is reported, and the regioisomeric effect on optoelectronic properties can be investigated based on all three isomers. Moreover, the single-crystal structure was successfully achieved for the symmetric molecule BTzIC-2Br-γ. With benzodithiophene (BDT)-free PFBT4T-T20 as an easily accessible and low-cost polymer donor, the three isomers could show differentiated device performances, with a power conversion efficiency order of BTzIC-2Br-γ (16.00%) > BTzIC-2Br-δγ (15.81%) > BTzIC-2Br-δ (15.29%). The best efficiency of 16.00% achieved with BTzIC-2Br-γ is among the highest ones for binary OSCs based on the low-cost BDT-free donors. The facile and complete synthesis of isomeric NFAs with mono-halogenated IC end-groups would promote the elucidation of the structure-property relationship.