Ring-opening polymerization of 1,4,8-trioxaspiro-[4.6]-9-undecanone: A route to novel molecular architectures for biodegradable aliphatic polyesters

Poly(ε-caprolactone)-Based Graft Copolymers: Synthesis Methods and Applications in the Biomedical Field: A Review

Synthetic biopolymers are attractive alternatives to biobased polymers, especially because they rarely induce an immune response in a living organism. Poly ε-caprolactone (PCL) is a well-known synthetic aliphatic polyester universally used for many applications, including biomedical and environmental ones. Unlike poly lactic acid (PLA), PCL has no chiral atoms, and it is impossible to play with the stereochemistry to modify its properties. To expand the range of applications for PCL, researchers have investigated the possibility of grafting polymer chains onto the PCL backbone. As the PCL backbone is not functionalized, it must be first functionalized in order to be able to graft reactive groups onto the PCL chain. These reactive groups will then allow the grafting of new reagents and especially new polymer chains. Grafting of polymer chains is mainly carried out by "grafting from" or "grafting onto" methods. In this review we describe the main structures of the graft copolymers produced, their different synthesis methods, and their main characteristics and applications, mainly in the biomedical field.

Surface modification of metallic cardiovascular stents by strongly adhering aliphatic polyester coatings

This article reports on a novel two-step strategy for the coating of cardiovascular stents by strongly adhering biocompatible and biodegradable aliphatic polyesters. First, a precoating of poly(ethylacrylate) (PEA) was electrografted onto the metallic substrate by cathodic reduction of the parent monomer in dimethylformamide (DMF). The electrodeposition of PEA, in a good solvent of it, was confirmed by both Infra-red and Raman spectroscopies. The pendant ester groups of PEA were then chemically reduced into aluminum alkoxides, able to initiate the ring-opening polymerization (ROP) of either D,L-lactide (LA) or epsilon-caprolactone (CL). Growth of biodegradable PLA or PCL coatings from the adhering precoating was confirmed by both Infra-red and Raman spectroscopies, and directly observed by scanning electron microscopy (SEM). This type of coating can act as an anchoring layer for the subsequent casting of drug-loaded polyester films allowing the controlled release of antiproliferative agents for the treatment of in-stent restenosis.

Versatile functionalization and grafting of poly(ε-caprolactone) by Michael-type addition

The Michael-type addition of aliphatic (co)polyesters onto gamma-acryloyloxy epsilon-caprolactone units is a very straightforward technique of functionalization and grafting, which is tolerant to a variety of functional groups and does not require intermediate protection/deprotection steps.

Amphiphilic copolymers of epsilon-caprolactone and gamma-substituted epsilon-caprolactone. Synthesis and functionalization of poly(D,L-lactide) nanoparticles

Fully biodegradable and surface-functionalized poly(D,L-lactide) (PLA) nanoparticles have been prepared by a co-precipitation technique. Novel amphiphilic random copolyesters P(CL-co-gammaXCL) were synthesized by controlled copolymerization of epsilon-caprolactone and epsilon-caprolactone substituted in the gamma-position by a hydrophilic X group, where X is either a cationic pyridinium (gammaPyCL) or a non-ionic hydroxyl (gammaOHCL). Nanoparticles were prepared by co-precipitation of PLA with the P(CL-co-gammaXCL) copolyester from a DMSO solution. Small amounts of cationic P(CL-co-gammaPyCL) copolymers are needed to quantitatively form stable nanoparticles (ca. 10 mg/ 100 mg PLA), although larger amounts of non-ionic P(CL-co-gammaOHCL) copolymers are needed (> or = 12.5 mg/ 100 mg PLA). Copolymers with a low degree of polymerization (ca. 40) are more efficient stabilizers, probably because of faster migration towards the nanoparticle-water interface. The nanoparticle diameter decreases with the polymer concentration in DMSO, e.g. from ca. 160 nm (16 mg/ml) to ca. 100 nm (2 mg/ml) for PLA/P(CL-co-gammaPyCL) nanoparticles. Migration of the P(CL-co-gammaXCL) copolyesters to the nanoparticle surface was confirmed by measurement of the zeta potential, i.e. ca. +65 mV for P(CL-co-gammaPCL) and -7 mV for P(CL-co-gammaOHCL). The polyamphiphilic copolyesters stabilize PLA nanoparticles by electrostatic or steric repulsions, depending on whether they are charged or not. They also impart functionality and reactivity to the surface, which opens up new opportunities for labelling and targeting purposes.