Development of a novel high quantum efficiency MV x-ray detector for image-guided radiotherapy: A feasibility study

A phantom based evaluation of the clinical imaging performance of electronic portal imaging devices

Purpose

In this study an evaluation of the imaging performance of an electronic portal imaging device (EPID) is presented. The evaluation performed employing the QC-3V image quality phantom.

Methods

An EPID system of a 6 MV LINAC, was used to obtain images of a QC-3V EPID phantom. The X-ray source to phantom distance was 100 cm and the field size was 15x15 cm2. The irradiation conditions comprised Dose Rates (DR) of 200, 400 and 600 for a 2 MU-100 MU range. The Contrast Transfer Function (CTF), the Noise Power Spectrum (NPS), the Normalized Noise Power Spectrum (NNPS) and the Contrast-to-Noise Ratio (CNR) were studied. In addition, an alternative factor showing a frequency related output signal-to-noise ratio (SNR), the Signal-to-Noise-Frequency Response (SNFR), has been introduced. SNFR is a comprehensive quality index, easily determined in clinical environment.

Results

The CTF curves were found comparable to each other. The lowest values were measured at 2 MU and 200 MU/min. Concerning the NPS and NNPS graphs it was found that the values decrease up to approximately 0.3 lp/mm and demonstrate a white noise shape afterwards. SNFR values were found reducing with spatial frequency. Highest CNR were found between the region 7 and 11 of the phantom.

Conclusions

The influence of MU and DR on EPID performance were investigated. Image quality was assessed using the QC-3V phantom. The presented results can lead to image quality amelioration and act supportively to current image quality control routine protocols.

Full modulation transfer functions of thick parallel- and focused-element scintillator arrays obtained by a Monte Carlo optical transport model

BACKGROUND

Arrays of thick segmented crystalline scintillators are useful x-ray converters for image-guided radiation therapy using electronic portal imaging (EPI) and megavoltage cone-beam computed tomography (MV-CBCT). Ionizing-radiation-only simulations previously showed relatively low modulation transfer function (MTF) in parallel-element arrays because of beam divergence. Hence, a focused-element geometry (matching the beam divergence) has been proposed. The "full" (ionizing and optical) MTF performance of such a focused geometry compared to its radiation-only MTF has, however, not been fully investigated.

PURPOSE

To study the full MTF performance of such arrays in a more realistic situation in which optical characteristics are also included using an in-house detector model that supports light transport, and quantify the errors in MTF estimation when the optical stage is ignored.

METHODS

First, radiation (x-ray and electron) transport was simulated. Then, transport of the generated optical photons was modeled using ScintSim2, an optical Monte Carlo (MC) code developed in MATLAB for simulation of two-dimensional (2D) parallel- and focused-element scintillator arrays. The full-MTF responses of focused- and parallel-element geometries, for a large array of 3 × 3 mm² CsI:Tl detector elements of 10, 40, and 60 mm thicknesses, were examined. For each configuration, a composite line spread function (LSF) was calculated to obtain the MTF.

RESULTS

At the Nyquist frequency, for 10 mm-thick central elements and 60 mm-thick peripheral parallel elements, full-MTF exhibited a drop of up to 15 and 79 times, respectively, compared with radiation-only MTF. This was found to be partly attributable to the angular distribution of the light emerging from the detector-element exit face and the dependence on its aspect ratio, since the light exiting thicker scintillators exhibited a more forward-directed distribution. Focused elements provided an increase of up to nine times in peripheral-area full MTF values.

CONCLUSIONS

Full MTF was up to 79 times lower than radiation-only MTF. Focused arrays preserved full MTF by up to nine times compared to parallel elements. The differences in the results obtained with and without inclusion of optical photons emphasize the need to include light transport when optimizing thick segmented scintillation detectors. Besides their application in detector optimization for radiotherapy megavoltage photon imaging, these findings can also be useful for other segmented-scintillator-based imaging systems, for example, in nuclear medicine, or in 2D detection systems for quality assurance of MR-linacs.

Performance of a new star-bar phantom designed for MTF calculations in x-ray imaging systems

PURPOSE

A new phantom, designed and manufactured for modulation transfer function (MTF) calculations is presented in this work. The phantom has a star-bar pattern and is manufactured in stainless steel. Modulation transfer function determinations are carried out with the new phantom and with an edge phantom to compare their performance and to compare them with previous theoretical predictions.

METHODS

The phantoms are imaged in an x-ray imaging system using different beam qualities and different entrance air KERMA. Methods, previously developed for synthetic images and simulations, are adapted to real measurements, solving practical implementation issues.

RESULTS

In the case of the star-bar, in order to obtain optimal MTF determinations it is necessary to accurately determine the center of the pattern. Also, to avoid underestimates in MTF calculations, the length in pixels of each of the scanning circumferences must be an integer multiple of the number of cycles in the pattern. Both methods, star-bar and edge, give similar mean values of the MTF in all cases analyzed. Also, the dependence with frequency of the experimental MTF standard deviation (SD) agrees with the theoretical expressions presented in previous works. In this regard, the precision is better for the star-bar method than for the edge and differences in precision between both methods are higher for the lowest beam quality.

CONCLUSIONS

The star-bar phantom can be used for MTF determinations with the advantage of having an improved precision. However, precision is reduced when the radiation quality increases. This fact suggests that, for the highest beam qualities, materials with an attenuation coefficient greater than that of steel should be used to manufacture the phantom.