Dual half-echo phase correction for implementation of 3D radial SSFP at 3.0 T

Rapid isotropic resolution cartilage assessment using radial alternating repetition time balanced steady-state free-precession imaging

PURPOSE

To compare a balanced steady-state free-precession sequence with a radial k-space trajectory and alternating repetition time fat suppression (Radial-ATR) with other currently used fat-suppressed 3D sequences for evaluating the articular cartilage of the knee joint at 3.0T.

MATERIALS AND METHODS

Radial-ATR, fast spin-echo (FSE-Cube), gradient recall-echo acquired in the steady-state (GRASS), and spoiled gradient recall-echo (SPGR) sequences with similar voxel volumes and identical scan times were performed at 3.0T on both knee joints of five volunteers. Signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) measurements were performed for all sequences using a double acquisition method and compared using Mann-Whitney Wilcoxon tests. Radial-ATR sequences with 0.3 mm and 0.4 mm isotropic resolution were also performed on the knee joints of seven volunteers and three patients with osteoarthritis.

RESULTS

Average SNR values for cartilage, synovial fluid, and bone marrow were 54.7, 153.3, and 12.9, respectively, for Radial ATR, 30.8, 44.1, and 1.9, respectively, for FSE-Cube, 13.3, 46.9, and 3.3, respectively, for GRASS, and 19.1, 8.1, and 2.1, respectively, for SPGR. Average CNR values between cartilage and synovial fluid and between cartilage and bone marrow were 98.6 and 41.8, respectively, for VIPR-ATR, 13.4 and 28.8, respectively, for FSE-Cube, 33.6 and 10.0, respectively, for GRASS, and 11.0 and 16.9, respectively, for SPGR. Radial-ATR had significantly higher (P < 0.001) cartilage, synovial fluid, and bone marrow SNR and significantly higher (P < 0.01) CNR between cartilage and synovial fluid and between cartilage and bone marrow than FSE-Cube, GRASS, and SPGR. Radial-ATR provided excellent visualization of articular cartilage at high isotropic resolution with no image degradation due to off-resonance banding artifacts.

CONCLUSION

Radial-ATR had superior SNR efficiency to other fat-suppressed 3D cartilage imaging sequences and produced high isotropic resolution images of the knee joint which could be used for evaluating articular cartilage at 3.0T.

High-resolution 3D radial bSSFP with IDEAL

Radial trajectories facilitate high-resolution balanced steady state free precession (bSSFP) because the efficient gradients provide more time to extend the trajectory in k-space. A number of radial bSSFP methods that support fat-water separation have been developed; however, most of these methods require an environment with limited B0 inhomogeneity. In this work, high-resolution bSSFP with fat-water separation is achieved in more challenging B0 environments by combining a 3D radial trajectory with the IDEAL chemical species separation method. A method to maintain very high resolution within the timing constraints of bSSFP and IDEAL is described using a dual-pass pulse sequence. The sampling of a unique set of radial lines at each echo time is investigated as a means to circumvent the longer scan time that IDEAL incurs as a multiecho acquisition. The manifestation of undersampling artifacts in this trajectory and their effect on chemical species separation are investigated in comparison to the case in which each echo samples the same set of radial lines. This new bSSFP method achieves 0.63 mm isotropic resolution in a 5-min scan and is demonstrated in difficult in vivo imaging environments, including the breast and a knee with ACL reconstruction hardware at 1.5 T.

Rapid measurement and correction of phase errors from B0 eddy currents: impact on image quality for non-Cartesian imaging

Non-Cartesian imaging sequences and navigational methods can be more sensitive to scanner imperfections that have little impact on conventional clinical sequences, an issue which has repeatedly complicated the commercialization of these techniques by frustrating transitions to multicenter evaluations. One such imperfection is phase errors caused by resonant frequency shifts from eddy currents induced in the cryostat by time-varying gradients, a phenomenon known as B(0) eddy currents. These phase errors can have a substantial impact on sequences that use ramp sampling, bipolar gradients, and readouts at varying azimuthal angles. We present a method for measuring and correcting phase errors from B(0) eddy currents and examine the results on two different scanner models. This technique yields significant improvements in image quality for high-resolution joint imaging on certain scanners. This result suggests that correcting short-time B(0) eddy currents that do not affect conventional clinical sequences may simplify the adoption of non-Cartesian methods.

Three-dimensional magnetic resonance imaging of joints

Magnetic resonance (MR) imaging is one of the most commonly used imaging modality for evaluating patients with joint pain. Musculoskeletal MR protocols at most institutions consist of 2-dimensional fast spin echo (FSE) sequences repeated in multiple planes. Three-dimensional sequences have also been used to evaluate the musculoskeletal system and have many potential advantages over 2-dimensional FSE sequences. Three-dimensional sequences acquire thin continuous slices through joints with high in-plane spatial resolution, which minimize the effects of partial volume averaging. Newly developed 3-dimensional isotropic resolution sequences can also be used to create high-quality multiplanar reformat images that allow joints to be evaluated in any orientation after a single acquisition. Preliminary results on the use of 3-dimensional isotropic resolution sequences for evaluating the musculoskeletal system are encouraging. However, additional studies are needed to document the advantages of 3-dimensional sequences before they can replace currently used 2-dimensional FSE sequences for evaluating the musculoskeletal system in clinical practice.