Small-animal, whole-body imaging with metamaterial-inspired RF coil

Preclinical validation of a metasurface-inspired conformal elliptical-cylinder resonator for wrist MRI at 1.5 T

OBJECTIVE

To design a metasurface-inspired conformal elliptical-cylinder resonator (MICER) for wrist magnetic resonance imaging at 1.5 T and evaluate its potential for clinical applications.

METHODS

An electromagnetic simulation was used to characterize the effect of MICER on radio frequency fields. A phantom and 14 wrists from 7 healthy volunteers were examined using a 1.5 T MRI system. The examination included T1-weighted spin echo, fat-saturation proton density-weighted fast spin echo, and three-dimensional T1-weighted gradient echo sequences. All scans were repeated using two methods: MICER combined with the spinal coil, which is a surface coil built-in examination table, and the 12-channel wrist array coil, to receive signals. Image signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) were calculated, and the differences between the two methods were compared using a paired Student's t-test.

RESULTS

In the phantom study, the image obtained with MICER had a higher SNR compared to the image obtained with the 12-channel wrist coil. Almost all wrist tissues showed a higher SNR on the images obtained with MICER than on the images obtained with the 12-channel wrist coil (P < 0.05). And the CNR between wrist tissues on images obtained with MICER was higher than that obtained with the 12-channel wrist coil (P < 0.05).

CONCLUSIONS

The quality of the MRI using MICER is superior to that of the commercially available 12-channel wrist coil, indicating its potential value for clinical practice.

Metamaterial-Enabled Hybrid Receive Coil for Enhanced Magnetic Resonance Imaging Capabilities

Magnetic resonance imaging (MRI) relies on high-performance receive coils to achieve optimal signal-to-noise ratio (SNR), but conventional designs are often bulky and complex. Recent advancements in metamaterial technology have led to the development of metamaterial-inspired receive coils that enhance imaging capabilities and offer design flexibility. However, these configurations typically face challenges related to reduced adaptability and increased physical footprint. This study introduces a hybrid receive coil design that integrates an array of capacitively-loaded ring resonators directly onto the same plane as the coil, preserving its 2D layout without increasing its size. Both the coil and metamaterial are individually non-resonant at the targeted Larmor frequency, but their mutual coupling induces a resonance shift, achieving a frequency match and forming a hybrid structure with enhanced SNR. Experimental validation on a 3.0 T MRI platform shows that this design allows for adjustable trade-offs between peak SNR and penetration depth, making it adaptable for various clinical imaging scenarios.

Stretchable receive coil for 7T small animal MRI

Receive coils used in small animal MRI are rigid, inflexible surface loops that do not conform to the anatomy being imaged. The recent trend toward design of stretchable coils that are tailored to fit any anatomical curvature has been focused on human imaging. This work demonstrates the application of stretchable coils for small animal imaging at 7T. A stretchable coil measuring 3.5 × 3.5 cm was developed for acquisition of rat brain and spine images. The SNR maps of the stretchable coil were compared with those of a traditional flexible PCB coil and a commercial surface coil. Stretch and conformance testing of the coil was performed. Ex vivo images of rat brain and spine from the stretchable a coil was acquired using T1 FLASH and T2 Turbo RARE sequences. The axial phantom SNR maps showed that the stretchable coil provided 48.5% and 42.8% higher SNR than the commercial coil for T1-w and T2-w images within the defined ROI. A 33% increase in average penetration depth was observed within the ROI using the stretchable coil when compared to the commercial coil. The ex-vivo rat brain and spine images showed distinguishable anatomical details. Stretching the coil reduced the resonant frequency with reduction in SNR, while the conformance to varying sample volumes increased the resonant frequency with decreased SNR. This study also features an open-source plug-and-play system with preamplifiers that can be used to interface surface coils with the 7T Bruker scanner.

Т1 mapping of rat lungs in 19 F MRI using octafluorocyclobutane

PURPOSE

To demonstrate the feasibility of using octafluorocyclobutane (OFCB, c-C₄ F₈ ) for T₁ mapping of lungs in ¹⁹ F MRI.

METHODS

The study was performed at 7 T in three healthy rats and three rats with pulmonary hypertension. To increase the sensitivity of ¹⁹ F MRI, a bent-shaped RF coil with periodic metal strips structure was used. The double flip angle method was used to calculate normalized transmitting RF field (B_1n ⁺ ) maps and for correcting T₁ maps built with the variable flip angle (VFA) method. The ultrashort TE pulse sequence was applied for acquiring MR images throughout the study.

RESULTS

The dependencies of OFCB relaxation times on its partial pressure in mixtures with oxygen, air, helium, and argon were obtained. T₁ of OFCB linearly depended on its partial pressure with the slope of about 0.35 ms/kPa in the case of free diffusion. RF field inhomogeneity leads to distortion of T₁ maps built with the VFA method, and therefore to high standard deviation of T₁ in these maps. To improve the accuracy of the T₁ maps, the B_1n ⁺ maps were applied for VFA correction. This contributed to a 2-3-fold decrease in the SD of T₁ values in the corresponding maps compared with T₁ maps calculated without the correction. Three-dimensional T₁ maps were obtained, and the mean T₁ in healthy rat lungs was 35 ± 10 ms, and in rat lungs with pulmonary hypertension - 41 ± 9 ms.

CONCLUSION

OFCB has a spin-rotational relaxation mechanism and can be used for ¹⁹ F T₁ mapping of lungs. The calculated OFCB maps captured ventilation defects induced by edema.

Design and first implementation of wireless square-shaped transmission line resonators in 1H MRI for small animal studies

This work is dedicated to the development of a novel design for wireless transmission line resonators (TLRs). The TLRs are often considered as circular-shaped coils made up of two conductive circuits separated by a dielectric layer. We propose a square-shaped TLR design, wherein the coil has two square turns with two symmetrical gaps on each of the conductive layers, and the latter are rotated relative to each other by 90°. The calculation error of the resonant frequency of the square-shaped TLRs is no more than ∼3% of the measured value. The effectiveness of the square-shaped TLR design was evaluated in comparative ¹H MRI studies to conventional wireless square loop of the same resonant frequency and with the same-sized inner square of the TLR. The Bruker birdcage was used as a transceiver and as inductively coupled with the wireless coils. We found that the performance of the square-shaped TLR and the square loop is comparable, but the B₁⁺-field generated by the TLR has a wider distribution profile. It was reflected in rat brain studies, when some structures of rat head were not captured by the square loop. Comparative experiments with a standard circular-shaped TLR showed that a signal is predominantly concentrated inside the inner turn of the TLRs. The proposed TLR design can be a promising path to be explored, especially for scanning small objects of study, when the scan area is comparable to the size of the rigid lumped capacitors.

Imaging Capabilities of the ¹H-X-Nucleus Metamaterial-Inspired Multinuclear RF-Coil

In this paper, we present the initial experimental investigation of a two-coil receive/transmit design for small animals imaging at 7T MRI. The system uses a butterfly-type coil tuned to 300 MHz for scanning the ¹H nuclei and a non-resonant loop antenna with a metamaterial-inspired resonator with the ability to tune over a wide frequency range for X-nuclei. ¹H, ³¹P, ²³Na and ¹³C, which are of particular interest in biomedical MRI, were selected as test nuclei in this work. Coil simulations show the two parts of the radiofrequency (RF) assembly to be decoupled and operating independently due to the orthogonality of the excited RF transverse magnetic fields. Simulations and phantom experimental imaging show sufficiently homogeneous transverse transmit RF fields and tuning capabilities for the pilot multiheteronuclear experiments.

Improving local SNR of a single-channel 54.6 mT MRI system using additional LC-resonator

Very-low field magnetic resonance imaging (VLF-MRI, B0 < 0.1T) has an essential application in medical imaging diagnosis because of its light weight and low cost. For single-channel RF coil VLF-MRI system, a planar spiral LC-resonator placed on the surface of samples was designed to improve the local SNR. First, an equivalent circuit model was established to evaluate the boosting effects on radiofrequency (RF) magnetic field and SNR. Second, the relationship between the resonant capacitance and the transmission coefficient was deduced according to the circuit model, and the appropriate resonant capacitance was obtained. Then, the influence of the diameter and the number of turns of the LC-resonator on the SNR is considered, and the structure of the LC-resonator was optimized to maximize the SNR. Finally, a phantom MRI experiment was carried out with our home-built 54.6 mT MRI system to compare the SNR of the experiment with the calculation, the SNR enhancement trend of the two was consistent. Additional experiments were conducted using orange and chicken leg to demonstrate the SNR enhancement abilities of the LC-resonator. The enhancement of SNR reached up to 1.8-fold and 2.2-fold depending on the distance between the sample and LC-resonator. For comparison, we conducted imaging experiments on surface receiving coil with the same parameters, and the results show that the SNR of the LC resonator is comparable to that of the surface coil. The reported LC-resonator provide a low-cost local enhancement method for VLF-MRI.

Adaptive Cylindrical Wireless Metasurfaces in Clinical Magnetic Resonance Imaging

The signal-to-noise ratio (SNR) is one of the most important criteria for evaluating the image quality in magnetic resonance imaging (MRI), and metasurfaces with unique electromagnetic properties provide a novel method for SNR improvement. However, their applications in clinical MRI are highly restricted by the inhomogeneous enhancement of the magnetic field and interference in the radio frequency (RF) transmitting field. In this study, an adaptive cylindrical wireless metasurface (ACWM) with homogeneous field enhancement and adaptive resonant modes is reported. The ACWM automatically switches its resonant modes between the partial (transmitting period) and whole (receiving period) resonance, which enables it to not only eliminate the interference in RF transmitting field, but also greatly enhance the SNR. Its adaptability also makes the ACWM applicable to all common clinical sequences without any modifications in the scan parameters. The SNR of MRI images of the human wrist, acquired with ACWM, is two to four times compared with the conventional coil. This work offers a practical control method to fill the scientific knowledge gaps between the preclinical research and medical applications for metasurfaces, and suggests a novel and powerful tool for diagnosing and evaluating human diseases.

The frontier of live tissue imaging across space and time

What you see is what you get-imaging techniques have long been essential for visualization and understanding of tissue development, homeostasis, and regeneration, which are driven by stem cell self-renewal and differentiation. Advances in molecular and tissue modeling techniques in the last decade are providing new imaging modalities to explore tissue heterogeneity and plasticity. Here we describe current state-of-the-art imaging modalities for tissue research at multiple scales, with a focus on explaining key tradeoffs such as spatial resolution, penetration depth, capture time/frequency, and moieties. We explore emerging tissue modeling and molecular tools that improve resolution, specificity, and throughput.

Metamaterial-Inspired Radiofrequency (RF) Shield With Reduced Specific Absorption Rate (SAR) and Improved Transmit Efficiency for UHF MRI

To prevent the interferences between radiofrequency (RF) coils and other components in the magnetic resonance imaging (MRI) system such as gradient coils, it is essential to place an RF shield between the RF coils and gradient coils. However, the induced currents on conventional RF shields have negative influences on the RF coil performance. To reduce these influences, metamaterial absorbers (MA), a class of metamaterials exhibiting nearly unity absorption rate for the incident electromagnetic fields, can be employed for the design of a novel RF shield. However, the adoption of metamaterials in MRI systems is usually problematic because of the bulkiness of the metamaterial structure. In this work, capacitors and metallic interconnectors are used to miniaturize the MA so that the unit MA cell can operate at the Larmor frequencies of 7T and 9.4T MRI and stay compact. This MA-RF shield is used to improve the transmit efficiency of RF surface coils and reduce the specific absorption rate (SAR) in the region of interest (ROI). It is successfully demonstrated by simulations and experiments that, compared with conventional RF shield structure, the transmit efficiency can be enhanced by more than 32% and the peak SAR value can be reduced by 22% using the MA-RF shield. Moreover, it is observed that the transmit field penetration is improved when the surface coil is used with the MA-RF shield. This proof-of-concept study suggests a new practical way for the utilization of metamaterials in ultra-high field MRI applications.

Hardware Considerations for Preclinical Magnetic Resonance of the Kidney

Magnetic resonance imaging (MRI) is a noninvasive imaging technology that offers unparalleled anatomical and functional detail, along with diagnostic sensitivity. MRI is suitable for longitudinal studies due to the lack of exposure to ionizing radiation. Before undertaking preclinical MRI investigations of the kidney, the appropriate MRI hardware should be carefully chosen to balance the competing demands of image quality, spatial resolution, and imaging speed, tailored to the specific scientific objectives of the investigation. Here we describe the equipment needed to perform renal MRI in rodents, with the aim to guide the appropriate hardware selection to meet the needs of renal MRI applications.This publication is based upon work from the COST Action PARENCHIMA, a community-driven network funded by the European Cooperation in Science and Technology (COST) program of the European Union, which aims to improve the reproducibility and standardization of renal MRI biomarkers. This chapter on hardware considerations for renal MRI in small animals is complemented by two separate publications describing the experimental procedure and data analysis.

Enhancing surface coil sensitive volume with hybridized electric dipoles at 17.2 T

Preclinical MR applications at 17.2 T can require field of views on the order of a few square centimeters. This is a challenging task as the proton Larmor frequency reaches 730 MHz. Most of the protocols at such frequencies are performed with surface transceiver coils for which the sensitive volume and the signal to noise ratio (SNR) is given by their size. Here we propose an approach based on metamaterials in order to enhance the sensitive volume of a commercial surface coil for small animal imaging at 17.2 T. We designed a passive resonator composed of four hybridized electric dipoles placed onto the floor of the MRI bed. Combining numerical and experimental results on a phantom and in vivo, we demonstrate a 20% increase of the sensitive volume in depth and 25% along the rostro-caudal axis while maintaining more than 85% of the local SNR right beneath the surface coil plane. Moreover, our solution gives the ability to double the average SNR in the region between 1.2 and 2 cm away from the loop using a single layer of 1 mm thick metallic wires easy to design and manufacture.

Four-Mode Programmable Metamaterial Using Ternary Foldable Origami

Designing a multifunctional metamaterial with programmable feature has become a new trend in mechanical, acoustic, and electromagnetic research fields due to the controllability of their structural behaviors and functionalities. The codable or reconfigurable structures have shown more remarkable characteristics than the traditional and conventional metamaterials to implement functional programmability. However, structural complexity and hi-tech requirement are the biggest constraints to their practical applications. This paper numerically and experimentally investigates a programmable metamaterial based on ternary foldable origami in the gigahertz-frequency regime. The proposed metamaterial provides four transformable modes corresponding to four different functions of electromagnetic reflector and frequency-selectable absorbers by programming unique ternary foldable origami coded as "0", "1", and "2" for different folding levels. Interestingly, the proposed foldable origami consists of a simple dielectric paper and a bottom conductor, while there is no conductive pattern on the top. Therefore, the proposed programmable metamaterial is extremely robust and can be extended to a multiresonance mode and origami computing.

Wireless coils based on resonant and nonresonant coupled-wire structure for small animal multinuclear imaging

Earlier work on RF metasurfaces for preclinical MRI has targeted applications such as whole-body imaging and dual-frequency coils. In these studies, a nonresonant loop was used to induce currents into a metasurface that was operated as a passive inductively powered resonator. However, as we show in this study, the strategy of using a resonant metasurface reduces the impact of the loop on the global performance of the assembled coil. To mitigate this deficiency, we developed a new approach that relies on the combination of a commercial surface coil and a coupled-wire structure operated away from its resonance. This strategy enables the extension of the sensitive volume of the surface coil while maintaining its local high sensitivity without any hardware modification. A wireless coil based on a two parallel coupled-wire structure was designed and electromagnetic field simulations were carried out with different levels of matching and coupling between both components of the coil. For experimental characterization, a prototype was built and tested at two frequencies, 300 MHz for ¹ H and 282.6 MHz for ¹⁹ F at 7 T. Phantom and in vivo MRI experiments were conducted in different configurations to study signal and noise figures of the structure. The results showed that the proposed strategy improves the overall sensitive volume while simultaneously maintaining a high signal-to-noise ratio (SNR). Metasurfaces based on coupled wires are therefore shown here as promising and versatile elements in the MRI RF chain, as they allow customized adjustment of the sensitive volume as a function of SNR yield. In addition, they can be easily adapted to different Larmor frequencies without loss of performance.