Optimizing the balance between impact strength and stiffness in polypropylene/elastomer blends by incorporation of a nucleating agent

Foams with Enhanced Ductility and Impact Behavior Based on Polypropylene Composites

In this work, formulations based on composites of a linear polypropylene (L-PP), a long-chain branched polypropylene (LCB-PP), a polypropylene-graft-maleic anhydride (PP-MA), a styrene-ethylene-butylene-styrene copolymer (SEBS), glass fibers (GF), and halloysite nanotubes (HNT-QM) have been foamed by using the improved compression molding route (ICM), obtaining relative densities of about 0.62. The combination of the inclusion of elastomer and rigid phases with the use of the LCB-PP led to foams with a better cellular structure, an improved ductility, and considerable values of the elastic modulus. Consequently, the produced foams presented simultaneously an excellent impact performance and a high stiffness with respect to their corresponding solid counterparts.

Waste Electrical and Electronic Equipment: A Review on the Identification Methods for Polymeric Materials

Considering that the large quantity of waste electrical and electronic equipment plastics generated annually causes increasing environmental concerns for their recycling and also for preserving of raw material resources, decreasing of energy consumption, or saving the virgin materials used, the present challenge is considered to be the recovery of individual polymers from waste electrical and electronic equipment. This study aims to provide an update of the main identification methods of waste electrical and electronic equipment such as spectroscopic fingerprinting, thermal study, and sample techniques (like identification code and burning test), and the characteristic values in the case of the different analyses of the polymers commonly used in electrical and electronic equipment. Additionally, the quality of the identification is very important, as, depending on this, new materials with suitable properties can be obtained to be used in different industrial applications. The latest research in the field demonstrated that a complete characterization of individual WEEE (Waste Electric and Electronic Equipment) components is important to obtain information on the chemical and physical properties compared to the original polymers and their compounds. The future directions are heading towards reducing the costs by recycling single polymer plastic waste fractions that can replace virgin plastic at a ratio of almost 1:1.

Effect of Mold Temperature on the Impact Behavior and Morphology of Injection Molded Foams Based on Polypropylene Polyethylene⁻Octene Copolymer Blends

In this work, an isotactic polypropylene (PP) and a polyethylene–octene copolymer (POE) have been blended and injection-molded, obtaining solids and foamed samples with a relative density of 0.76. Different mold temperature and injection temperature were used. The Izod impact strength was measured. For solids, higher mold temperature increased the impact resistance, whereas in foams, the opposite trend was observed. In order to understand the reasons of this behavior, the morphology of the elastomeric phase, the crystalline morphology and the cellular structure have been studied. The presence of the elastomer near the skin in the case of high mold temperature can explain the improvement produced with a high mold temperature in solids. For foams, aspects as the elastomer coarsening in the core of the sample or the presence of a thicker solid skin are the critical parameters that justify the improved behavior of the materials produced with a lower mold temperature.

Preparation of Piezo-Resistive Materials by Combination of PP, SEBS and Graphene

The use of polyolefins in structural components requires the simultaneous improvement of stiffness and toughness of the matrix, whilst in the case of sensing components during operation, additional functions are needed such as electrical conductivity. However, providing various desired properties without impairing those intrinsic to the materials can be somewhat challenging. In this study we report the preparation of an isotactic polypropylene (iPP)/styrene–ethylene–butylene–styrene triblock copolymer (SEBS)/graphene system that combines enhanced mechanical properties with electrical conductivity. Blends were prepared by solution mixing (SoM) and solution/solid state mixing (SoM/SSM) formulation routes prior to melt processing. The nanocomposites were characterized by scanning electron microscopy (SEM) and thermogravimetric analysis (TGA) and the electrical and mechanical properties were evaluated. The materials prepared via the SoM/SSM route displayed good electrical conductivity while retaining the mechanical properties of iPP, making them attractive materials for low cost and high throughput structural components with sensing capacity.

Nucleation of Polypropylene Homo- and Copolymers

The combination of moderately slow crystal growth at large undercoolings together with the practical absence of sporadic nucleation makes isotactic polypropylene (iPP) an ideal material for controlled nucleation. In this review the different types of nucleating agents – inorganic and organic, particulate and soluble – for the different crystal modifications of iPP (α, β and γ) are presented together with their working mechanism and criteria for activity. The interaction between polymer type, nucleating agent and processing conditions in determining mechanical and optical properties conclude the survey.