Hybrid factors influencing wet grip and rolling resistance properties of solution styrene-butadiene rubber composites

Abrasion Behaviors of Silica-Reinforced Solution Styrene-Butadiene Rubber Compounds Using Different Abrasion Testers

Solution styrene-butadiene rubber (SSBR) is widely used to improve the properties of tire tread compounds. Tire wear particles (TWPs), which are generated on real roads as vehicles traverse, represent one of significant sources of microplastics. In this study, four SSBR compounds were prepared using two SSBRs with high styrene (STY samples) and 1,2-unit (VIN samples) contents, along with dicyclopentadiene resin. The abrasion behaviors were investigated using four different abrasion testers: cut and chip (CC), Lambourn, DIN, and laboratory abrasion tester (LAT100). The abrasion rates observed in the Lambourn and LAT100 abrasion tests were consistent with each other, but the results of CC and DIN abrasion tests differed from them. The addition of the resin improved the abrasion rate and resulted in the generation of large wear particles. The abrasion rates of STY samples in the Lambourn and LAT100 abrasion tests were lower than those of VIN samples, whereas the values in the CC and DIN abrasion tests were higher than those of VIN samples. The wear particles were predominantly larger than 1000 μm, except for the VIN sample in the DIN abrasion test. However, TWPs > 1000 μm are rarely produced on real roads. The size distributions of wear particles > 1000 μm were 74.0-99.5%, 65.9-93.4%, 7.2-95.1%, and 37.5-83.0% in the CC, Lambourn, DIN, and LAT100 abrasion tests, respectively. The size distributions of wear particles in the Lambourn and LAT100 abrasion tests were broader than those in the other tests, whereas the distributions in the CC abrasion test were narrower. The abrasion patterns and the morphologies and size distributions of wear particles generated by the four abrasion tests varied significantly, attributable to differences in the bound rubber contents, crosslink densities, and tensile properties.

Investigation on in situ silica dispersed in natural rubber latex matrix combined with spray sputtering technology

In this study, different processes are performed for the preparation of natural rubber latex (NRL)/silica composites. A novel approach is to use spray sputtering technology combined with in situ method to improve the dispersion of silica in rubber latex matrix and further improve the properties of vulcanizates. Results show that in situ silica in rubber matrix prepared from NH4Cl and Na2SiO3 has better Payen effect than other processes. Meanwhile, when the in situ silica reached 10 phr in the rubber matrix, the dosage can suitably match the dispersion capacity of the spray sputtering process with superior comprehensive mechanical properties. Compared with the traditional precipitation method, the tensile strength and tear strength of the silica/NR composites prepared by spray sputtering technology combined with in situ method were increased by 34.7% and 19.7%.

Maleic Anhydride Modified Dicyclopentadiene Resin for Improving Wet Skid Resistance of Silica Filled SSBR/BR Composites

As commercial rubber in tires, silica-filled solution-polymerized styrene-butadiene rubber/butadiene rubber (SSBR/BR) compounds exhibited preferable wet skid resistance (WSR) properties, which could be further enhanced by the incorporation of some oligomeric resins. However, the untreated dicyclopentadiene (DCPD) resin shows a slight improvement in wet friction even if the good compatibility between DCPD and SBR owing to their common cyclic structures. For this problem to be addressed, we aimed to enhance its resin-silica interaction by reaction with maleic anhydride (MAH). In detail, the effect of MAH content on WSR, curing characteristics, physical-mechanical properties of the silica-filled SSBR/BR composites was investigated. When the MAH content is 4 wt% in the modified DCPD resin, the maximum enhancement of about 15% in tan δ values at 0 °C, as well as that of 17% in British pendulum skidding tester (BPST) index is obtained, indicating a desirable improvement in WSR. In addition of these two commonly used methods, water contact angles of the vulcanizates increase gradually with increasing MAH content, further confirming the remarkable performance of modified DCPD resin in WSR.