The infrared determination of the degree of crystallinity of polyethylene crystallized from dilute solution

Repurposing the single-used-plastic for development of hydrophobic aerogels for remediation of oil spill and organic solvents

Currently, around 400 million tonnes of synthetic polymers are being dumped as waste annually and by this rate by 2050 the ocean would contain more such waste compared to the total weight of fish. As recycling could solve part of this problem, recently such waste is being reused for various purposes like composite preparation, oil production and various other use such as production of foams, sponges, and aerogels. However, there is a relatively limited literature available on the utilization of polyethylene polymer (like LDPE). The study presented in this article indicated that LDPE-based polymers could be reused (after modification) for preparation of hydrophobic, lightweight, and porous aerogels that have oil-spills and organic solvent adsorption capacity. The aerogels showed contact angle of 121.9o, bulk density below 0.25 g/cm3, and were found to be semi-crystalline. The aerogels showed oil and solvent adsorption more than that for their untreated counterparts. Also, the aerogels were found to be recycled for more than five cycles with very minimum loss of efficacy. This area of producing oil sorbents from single used plastic wastes is still very open for further research and seems to be a promising route for both waste reduction, and the synthesis of value-added products. This could be one of the most sustainable approaches for efficient single-used plastic wase management and environment clean-up.

The effect of an additional phosphite stabilizer on the properties of radiation cross-linked vitamin E blends of UHMWPE

Antioxidant stabilization of radiation cross-linked ultrahigh molecular weight polyethylene (UHMWPE) has been introduced to improve the oxidative stability of total joint implant bearing surfaces. Blending of an antioxidant with UHMWPE resin powder followed by consolidation and radiation cross-linking has been cleared by the FDA for use in both total hips and total knees for designs incorporating two antioxidants, namely vitamin E and Covernox™ (a medical grade version of Irganox™ 1010). The antioxidants in the polymer are expected to protect the polymer during consolidation, during radiation cross-linking, on the shelf before implantation, and in vivo after implantation. To maximize the protection of the polymer afforded by the antioxidant in vivo, a novel approach may be the use of multiple antioxidants, especially to protect the primary antioxidant for a longer period of time. We hypothesized that the addition of a phosphite stabilizer (Irgafos 168™) commonly used in conjunction with hindered phenolic antioxidants in polymer processing could improve the oxidative stability of radiation cross-linked blends of vitamin E. To test our hypothesis, we prepared UHMWPE blends with 0.05 wt% Irgafos and 0.05 wt% vitamin E and compared its cross-link density, wear resistance, tensile properties, and impact strength to control blends containing only vitamin E. Our hypothesis was not supported; the cross-link density of UHMWPE was significantly decreased by the additive without additional benefit to oxidative stability. To our knowledge, this was the first attempt at using multiple stabilizers in medical grade UHMWPE.

Surface cross-linked UHMWPE can enable the use of larger femoral heads in total joints

Limiting cross-linking to the articular surfaces of ultrahigh molecular weight polyethylene (UHMWPE) to increase wear resistance while preventing detrimental effects of cross-linking on mechanical strength has been a desirable goal. A surface cross-linked UHMWPE can be achieved by blending UHMWPE with a free radical scavenger, such as vitamin E, consolidating the blend into an implant shape, extracting the vitamin E from the surface, and radiation cross-linking the surface extracted blend. This process results in high cross-link density in the vitamin E-depleted surface region because vitamin E hinders cross-linking during irradiation. In this study, we described the properties of successful extraction media and the manipulation of the wear and mechanical properties of extracted, irradiated blends. We showed that these formulations could have similar wear and significantly improved mechanical properties compared to currently available highly cross-linked UHMWPEs. We believe that these materials can enable thinner implant forms and more anatomical designs in joint arthroplasty and may provide a feasible alternative to metal-on-metal implants.