Bicarbazole‐based oxalates as photoinitiating systems for photopolymerization under UV–Vis LEDs

Development of Drug-Loaded PCL@MOF Film Enclosed in a Photo Polymeric Container for Sustained Release

The programmed fabrication of oral dosage forms is associated with several challenges such as controlled loading and disintegration. To optimize the drug payload, excipient breakdown, and site-specific sustained release of hydrophobic drug (sulfamethoxazole, SM), we propose the development of acrylate polymer tablets enclosed with drug-loaded polycaprolactone (PCL) films. The active pharmaceutical ingredient (API) is physisorbed into the porous iron (Fe)-based metal-organic framework (MOF) and later converted to tangible PCL films, which, upon folding, are incorporated into the acrylate polymer matrices (P1/P2/P3). X-ray powder diffraction (XRPD) analysis and scanning electron microscopy (SEM) micrographs confirmed the stability and homogeneous distribution of MOF within the 50 μm thick film. Adsorption-desorption measurements at ambient temperatures confirmed the decrease in the BET surface area of PCL films by 40%, which was ∼3.01 m/g, and pore volume from 30 to 9 nm. The decrease in adsorption and surface parameters could confirm the gradual accessibility of SM molecules once exposed to a degrading environment. Fourier transform infrared (FTIR) analyses of in vitro dissolution confirmed the presence of the drug in the MOF-PCL film-enclosed tablets and concluded the cumulative SM release at pH ∼ 8.2 which followed the order SM@Fe-MOF < P1/P2/P3 < PCL-SM@Fe-MOF < P1/PCL-SM@Fe-MOF < P3/PCL-SM@Fe-MOF. The results of the study indicate that the P3/PCL-SM@Fe-MOF assembly has potential use as a biomedical drug delivery alternative carrier for effective drug loading and stimuli-responsive flexible release to attain high bioavailability.

Rationally designed Tröger's base decorated bis-carbazoles as twisted solid-state emitting materials and dead bacterial cell imaging

Troger's base decorated bis-carbazoles were investigated as solid-state emitting materials for dead bacterial staining agents to assess bacterial cell death based on fluorescence.

Fused Carbazole–Coumarin–Ketone Dyes: High Performance and Photobleachable Photoinitiators in Free Radical Photopolymerization for Deep Photocuring under Visible LED Light Irradiation

In this work, three dyes based on fused carbazole–coumarin–ketone structures were designed and synthesized. These dyes were named CCK–Me, CCK–Ph, and CCK–Tol in accordance with their different substituents. Their excellent...

High Efficiency and Low Migration Hyperbranched Silicone Contain Macrophotoinitiators for UV-Cured Transparent Coatings

A kind of hyperbranched silicone containing macrophotoinitiators (HBSMIs) were synthesized from 2-hydroxy-2-methyl-1-phenyl propanone (HMPP) and the UV-curing behaviors of HBSMIs were investigated in UV-cured transparent polyurethane-acrylate (PUA) coatings. HBSMIs show higher UV-initiating efficiency than HMPP. The migration of HBSMIs from the UV-cured coatings can be as low as 1.7–6.0 wt%, which is obviously lower than the migration of HMPP. There is a remarkable improvement of the tensile strength of the UV-cured materials initiated by HBSMI in comparison to that of the materials prepared with the same PUA initiated by HMPP. Especially for the UV-cured materials prepared from PUA with 20 wt% 1,1,1-tris(hydroxymethyl)propane (TMP), the tensile strength and the strain at break increased from 6.81 MPa to 12.14 MPa and from 43.0% to 71.9%, respectively. The fraction of improvement for the tensile strength and the strain at break is as high as 78.9% and 67.2%, respectively. The coatings prepared with HBSMI also have better UV resistance ability than those coatings prepared with HMPP because they turn slightly yellow when they are aged by UV for about 15 min while the coating prepared with 4 wt% of HMPP will turn yellow only aged by UV for 2 min. These results suggest that preparation hyperbranched silicone containing macrophotoinitiators will be one of the good strategies to improve the curing efficiency of the UV-curing system, reduce the migration of UV initiator from cured material, improve the mechanical and UV resistance performance of UV-cured materials.