Isoprene polymerizationvia reversible addition fragmentation chain transfer polymerization

Synthesis of Mechanically Robust Very High Molecular Weight Polyisoprene Particle Brushes by Atom Transfer Radical Polymerization

Linear polyisoprene (PI) and SiO2-g-PI particle brushes were synthesized by both conventional and activators regenerated by electron transfer (ARGET) atom transfer radical polymerization (ATRP). The morphology and solution state study on the particle brushes by transmission electron microscopy (TEM) and dynamic light scattering (DLS) confirmed the successful grafting of PI ligands on the silica surface. The presence of nanoparticle clusters suggests low grafting density (associated with the limited initiation efficiency of ARGET for PI). Nevertheless, particle brushes with very high molecular weights, Mn > 300,000, were prepared, which significantly improved the dispersion of silica nanoparticles and also contributed to excellent mechanical performance. The reinforcing effects of SiO2 nanofillers and very high molecular weight PI ligands were investigated by dynamic mechanical analysis (DMA) as well as computational simulation for the cured linear PI homopolymer/SiO2-g-PI particle brush bulk films.

Polymeric Microcapsules as Robust Mimics of Emulsion Liquid Membranes for Selective Ion Separations

Selective ion separations are increasingly needed to combat water scarcity, recover resources from wastewater, and enable the efficient recycling of electronics waste. Emulsion liquid membranes (ELMs) have received interest due to rapid kinetics, high selectivities, and low solvent requirements but are too unstable for industrial usage. We demonstrate that polymeric microcapsules can serve as robust, solvent-free mimics of ELMs. As a proof of concept, we incorporated the copper-selective ligand Lix 84-I in the walls of microcapsules formed from a commercial polystyrene-b-polybutadiene-b-polystyrene triblock polymer. The microcapsules were formed from a double-emulsion template, resulting in particles typically 20-120 μm in diameter that encapsulated even smaller droplets of a dilute (≤0.5 M) H₂SO₄ solution. Batch experiments demonstrated facilitated-transport behavior, with equilibrium reached in as little as 10 min for microcapsules with 1% ligand, and with ∼15-fold selectivity for Cu²⁺ over Ni²⁺. Furthermore, the microcapsules could be packed readily in columns for flow-through operation, thus enabling near-complete Cu²⁺ removal in ∼2 min under certain conditions, recovery of Cu²⁺ by flowing through fresh dilute H₂SO₄, and reuse for at least 10 cycles. The approach in this work can serve as a template for using selective ligands to enable robust and simple flow-through processes for a variety of selective ion separations.

Functionalized Polymersomes from a Polyisoprene-Activated Polyacrylamide Precursor

Self-assembled polymer nanoparticles have tremendous potential in biomedical and environmental applications. For all applications, tailored polymer chemistries are critical. In this study, we demonstrate a precursor approach in which an activated, organic solvent-soluble block polymer precursor is modified through mild postpolymerization modifications to access new polymer structures. We synthesized and characterized poly(isoprene)-block-poly(di-Boc acrylamide) diblock polymers. This activated-acrylamide-based polymer was then reacted with amines or reductants in the absence of catalysts to yield the hydrophilic blocks polyacrylamide, poly(hydroxypropylene), and poly(N-ethyl acrylamide). The resulting amphiphilic block polymers self-assembled in water to form polymersomes, as confirmed by cryo-electron microscopy and confocal microscopy. The approach also enables simple functionalization with specialized ligands, which we demonstrated by tagging polymers with an amino-fluorophore and imaging by confocal microscopy. We expect that the methodologies established in this study will open doors to new and useful solution nanostructures with surface chemistries that can be optimized for various applications.

Semiautomated Parallel RAFT Copolymerization of Isoprene with Glycidyl Methacrylate

Copolymerization of isoprene (IP) with glycidyl methacrylate (GMA) was performed under RAFT (reversible addition-fragmentation chain-transfer) polymerization conditions in a platform for high-output experimentation. Covering the range between 1 and 0.2 molar fraction of IP in the feed, four sets of reactions were carried out at 10, 15, 20, and 30 h at 115 °C. The kinetic data obtained were used to estimate the reactivity ratios using a nonlinear least-squares approach (NLLS). Reactivity ratios r_GMA = 0.61 and r_IP = 0.74 indicate that both monomers tend to crosspropagate in agreement with known literature values. Concerning the RAFT study, relatively good control and livingness of the copolymerization was observed except for the experiment in which IP represents 20 mol % in the feed. ¹H NMR characterization confirmed the presence of both monomers in the final copolymer, particularly the presence of the epoxy ring of GMA which is susceptible to post polymerization reactions. Finally, preliminary results on the hydrogenation of various polymers are discussed.

Mild synthesis of environment-friendly thermoplastic triblock copolymer elastomers through combination of ring-opening and RAFT polymerization

Environment-friendly thermoplastic triblock copolymer elastomers, polylactide-block-polyisoprene-block-polylactide, were synthesized by a mild ROP and RAFT method.

Normal, ICAR and photomediated butadiene-ATRP with iron complexes

FeX₂ or FeX₃ (X = Cl ≫ Br) alone or with P ≫ X > O > N > C ligands and bromoester initiators enable the successful ATRP of butadiene in toluene at 110 °C.

One-pot synthesis of block-copolyrotaxanes through controlled rotaxa-polymerization

The aqueous reversible addition fragmentation chain-transfer (RAFT) copolymerization of isoprene and bulky comonomers, an acrylate and an acrylamide in the presence of methylated β-cyclodextrin was employed for the first time to synthesize block-copolyrotaxanes. RAFT polymerizations started from a symmetrical bifunctional trithiocarbonate and gave rise to triblock-copolymers where the outer polyacrylate/polyacrylamide blocks act as stoppers for the cyclodextrin rings threaded onto the inner polyisoprene block. Statistical copolyrotaxanes were synthesized by RAFT polymerization as well. RAFT polymerization conditions allow control of the composition as well as the sequence of the constituents of the polymer backbone which further effects the CD content and the aqueous solubility of the polyrotaxane.

Nanoporous Block Polymer Thin Films Functionalized with Bio-Inspired Ligands for the Efficient Capture of Heavy Metal Ions from Water

Heavy metal contamination of water supplies poses a serious threat to public health, prompting the development of novel and sustainable treatment technologies. One promising approach is to molecularly engineer the chemical affinity of a material for the targeted removal of specific molecules from solution. In this work, nanoporous polymer thin films generated from tailor-made block polymers were functionalized with the bio-inspired moieties glutathione and cysteamine for the removal of heavy metal ions, including lead and cadmium, from aqueous solutions. In a single equilibrium stage, the films achieved removal rates of the ions in excess of 95%, which was consistent with predictions based on the engineered material properties. In a flow-through configuration, the thin films achieved an even greater removal rate of the metal ions. Furthermore, in mixed ion solutions the capacity of the thin films, and corresponding removal rates, did not demonstrate any reduction due to competitive adsorption effects. After such experiments the material was repeatedly regenerated quickly with no observed loss in capacity. Thus, these membranes provide a sustainable platform for the efficient purification of lead- and cadmium-contaminated water sources to safe levels. Moreover, their straightforward chemical modifications suggest that they could be engineered to treat sources containing other recalcitrant environmental contaminants as well.

Unusually Stable Hysteresis in the pH-Response of Poly(Acrylic Acid) Brushes Confined within Nanoporous Block Polymer Thin Films

Stimuli-responsive soft materials are a highly studied field due to their wide-ranging applications; however, only a small group of these materials display hysteretic responses to stimuli. Moreover, previous reports of this behavior have typically shown it to be short-lived. In this work, poly(acrylic acid) (PAA) chains at extremely high grafting densities and confined in nanoscale pores displayed a unique long-lived hysteretic behavior caused by their ability to form a metastable hydrogen bond network. Hydraulic permeability measurements demonstrated that the conformation of the PAA chains exhibited a hysteretic dependence on pH, where different effective pore diameters arose in a pH range of 3 to 8, as determined by the pH of the previous environment. Further studies using Fourier transform infrared (FTIR) spectroscopy demonstrated that the fraction of ionized PAA moieties depended on the thin film history; this was corroborated by metal adsorption capacity, which demonstrated the same pH dependence. This hysteresis was shown to be persistent, enduring for days, in a manner unlike most other systems. The hypothesis that hydrogen bonding among PAA units contributed to the hysteretic behavior was supported by experiments with a urea solution, which disrupted the metastable hydrogen bonded state of PAA toward its ionized state. The ability of PAA to hydrogen bond within these confined pores results in a stable and tunable hysteresis not previously observed in homopolymer materials. An enhanced understanding of the polymer chemistry and physics governing this hysteresis gives insight into the design and manipulation of next-generation sensors and gating materials in nanoscale applications.

Pyridyl-phenylethynylene bis-urea macrocycles: self-assembly and utility as a nanoreactor for the selective photoreaction of isoprene

Porous organic crystals with one dimensional channels facilitate stereoselective polymerization to produce trans-1,4-polyisoprene with low PDI under mild UV-irradiation.

Polyisoprene synthesized via cationic polymerization: State of the art

In this paper, more than 70 years of cationic polymerization of isoprene (IP) are reviewed. Up to now, the controlled or living cationic polymerization of IP was never reported due to numerous side reactions, including chain transfer, cyclization, and cross-linking reactions that were very difficult to control. Cationic polyisoprenes (PIPs) are thus described to be mainly 1,4-trans with saturated/cyclized sequences. Although progress was made for their characterization due to many analysis techniques, cationic PIPs are still not yet fully characterized, particularly the saturated sequences. As a consequence, even if suggestions are proposed, polymerization mechanism is still not fully elucidated.

Evaluation of Isoprene Chain Extension from PEO Macromolecular Chain Transfer Agents for the Preparation of Dual, Invertible Block Copolymer Nanoassemblies

Two RAFT-capable PEO macro-CTAs, 2 and 5 kDa, were prepared and used for the polymerization of isoprene which yielded well-defined block copolymers of varied lengths and compositions. GPC analysis of the PEO macro-CTAs and block copolymers showed remaining unreacted PEO macro-CTA. Mathematical deconvolution of the GPC chromatograms allowed for the estimation of the blocking efficiency, about 50% for the 5 kDa PEO macro-CTA and 64% for the 2 kDa CTA. Self assembly of the block copolymers in both water and decane was investigated and the resulting regular and inverse assemblies, respectively, were analyzed with DLS, AFM, and TEM to ascertain their dimensions and properties. Assembly of PEO-b-PIp block copolymers in aqueous solution resulted in well-defined micelles of varying sizes while the assembly in hydrophobic, organic solvent resulted in the formation of different morphologies including large aggregates and well-defined cylindrical and spherical structures.