From rosin to novel bio-based silicone rubber: a review

Rosin is a characteristic natural renewable resource. In view of the unique hydrogenated phenanthrene ring skeleton structure of rosin, it can be designed and synthesized to modify silicone rubber for improving its mechanical properties, thermal stability, and other properties. In this paper, the research progress of silicone rubber modified by rosin and its derivatives is reviewed, including internal or surface modification of room temperature or high temperature vulcanized silicone rubber. The different chemical modifications and polymerization pathways to obtain bio-based silicone rubber (e.g. rosin-based silicone cross-linking agent, filler compound rosin-based silicone cross-linking agent, rosin-based polymer, and rosin quaternary ammonium salt bifunctional antibacterial coating) are discussed and its research prospect is reviewed. Overall, the present review article will provide a quantitative experimental basis for rosin to produce bio-renewable multifunctional silicone rubber to increase our level of understanding of the behavior of this important class of silicone rubber and other similar bio-based polymers.

Improvement of Heat Resistance of Fluorosilicone Rubber Employing Vinyl-Functionalized POSS as a Chemical Crosslinking Agent

Fluorosilicone rubber (F-LSR) is a promising material that can be applied in various cutting-edge industries. However, the slightly lower thermal resistance of F-LSR compared with that of conventional PDMS is difficult to overcome by applying nonreactive conventional fillers that readily agglomerate owing to their incompatible structure. Polyhedral oligomeric silsesquioxane with vinyl groups (POSS-V) is a suitable material that may satisfy this requirement. Herein, F-LSR-POSS was prepared using POSS-V as a chemical crosslinking agent chemically bonded with F-LSR through hydrosilylation. All F-LSR-POSSs were successfully prepared and most of the POSS-Vs were uniformly dispersed in the F-LSR-POSSs, as confirmed by Fourier transform infrared spectroscopy (FT-IR), proton nuclear magnetic resonance spectroscopy (1H-NMR), scanning electron microscopy (SEM), and X-ray diffraction (XRD) measurements. The mechanical strength and crosslinking density of the F-LSR-POSSs were determined using a universal testing machine (UTM) and dynamic mechanical analysis (DMA), respectively. Finally, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) measurements confirmed that the low-temperature thermal properties were maintained, and the heat resistance was significantly improved compared with conventional F-LSR. Eventually, the poor heat resistance of the F-LSR was overcome with three-dimensional high-density crosslinking by introducing POSS-V as a chemical crosslinking agent, thereby expanding the potential fluorosilicone applications.

Optimization and Characterization of the F-LSR Manufacturing Process Using Quaternary Ammonium Silanolate as an Initiator for Synthesizing Fluorosilicone

Due to the growing demand for versatile hybrid materials that can withstand harsh conditions (below -40 °C), fluorosilicone copolymers are becoming promising materials that can overcome the limited operating temperature of conventional rubber. In order to synthesize a fluorosilicone copolymer, a potent initiator capable of simultaneously initiating various siloxane monomers in anionic ring-opening polymerization (AROP) is required. In this study, tetramethyl ammonium silanolate (TMAS), a quaternary ammonium (QA) anion, was employed as an initiator for AROP, thereby fluoro-methyl-vinyl-silicone (FVMQ) and fluoro-hydrido-methyl-silicone (FHMQ) were successfully synthesized under optimized conditions. FT-IR, NMR, and GPC analyses confirmed that the chain length and functional group content of FVMQ and FHMQ are controlled by changing the ratio of the components. Moreover, fluorine-involved liquid silicone rubber (F-LSR) was prepared with FVMQ as the main chain and FHMQ as a crosslinker. The tensile strength, elongation, and hardness of each F-LSR sample were measured. Finally, it was confirmed through TGA, DSC, TR-test, and embrittlement testing that elastic retention at low temperatures improved even though the heat resistance slightly decreased as the trifluoropropyl group increased in F-LSR. We anticipate that the optimization of fluorosilicone synthesis initiated by QA and the comprehensive characterization of F-LSRs with different fluorine content and chain lengths will be pivotal to academia and industry.

Using α-Pinene-Modified Triethoxysilane as the New Cross-Linking Agent To Improve the Silicone Rubber Properties

α-Pinene-modified triethoxysilane (α-PTES) was synthesized by hydrosilylation in the presence of Karstedt's catalyst. The structure of α-PTES was determined by Fourier transform infrared spectroscopy and nuclear magnetic resonance. Under the catalysis of an organotin catalyst, α-PTES, which was the cross-linking agent, and the hydroxy-terminated poly(dimethylsiloxane) matrix were utilized to prepare the room-temperature vulcanized silicone rubber. Morphology, thermal performance, and mechanical properties of the modified silicone rubber were investigated by scanning electron microscopy, thermal gravimetric analysis, dynamic mechanical analysis, and a universal testing machine. Because of the strong rigidity of the ring structure of α-pinene, the thermal and mechanical properties of modified silicone rubber were improved greatly than those of the silicone rubber, and the cross-linking agent of which was methyltriethoxysilane. Results showed that the tensile strength and the break at elongation increased by 69.2 and 125%, respectively, and they are nearly doubled compared to the unmodified silicone rubber.

Synthesis and Characterization of Room Temperature Vulcanized Silicone Rubber Using Methoxyl-Capped MQ Silicone Resin as Self-Reinforced Cross-Linker

Methoxyl-capped MQ silicone resin (MMQ) was first synthesized by the hydrosilylation of vinyl-containing MQ silicone resin and trimethoxysilane and then used in condensed room-temperature vulcanized (RTV) silicone rubber as a self-reinforced cross-linker. Results show that modified silicone rubber exhibits good light transmission. Compared with unmodified silicone rubber, the hardness, tensile strength and elongation of MMQ at the break are increased by 26.4 A, 2.68 MPa and 65.1%, respectively. In addition, the characteristic temperature of 10% mass loss is delayed from 353.5 °C to 477.1 °C, the temperature at maximum degradation rate is also delayed from 408.9 °C to 528.4 °C and the residual mass left at 800 °C is increased from 1.2% to 27.7%. These improved properties are assigned to the synergistic effect of the rigid structure of MMQ, the formation of a dense cross-linking structure in polymers and the uniform distribution of MMQ cross-linking agent in RTV silicone rubber.

Aggregation Behavior of "Linear" Trisiloxane Surfactant with Different Terminal Groups (CH3-, ClCH2-, and CF3-) in Aqueous Solution

Novel "linear" trisiloxane surfactants with different terminal groups (CH₃-, ClCH₂-, CF₃-) and two polyether hydrophilic groups were successfully synthesized and confirmed using ¹H NMR, ¹³C NMR, ²⁹Si NMR, and FT-IR spectroscopy. The aggregation and adsorption behavior of the "linear" trisiloxane surfactants in aqueous solution was studied by surface tension, dynamic light scattering (DLS), transmission electron microscopy (FF-TEM), and TEM. Owing to the introduction of two polyether hydrophilic groups in the terminal positions of the trisiloxane hydrophobic part, "linear" trisiloxane surfactants (Me-Si₃-EO₈, Cl-Si₃-EO₈, and F-Si₃-EO₈) tend to lie flat in the air/water interface and result in an increasing the surface tension at the CMC ( γ_CMC) and single trisiloxane surfactant molecule at the air/water interface ( A _min) values. Following the difference in the intermolecular forces and molecular volumes (CH₃- < ClCH₂- < CF₃-), the γ_CMC values decrease following the order Me-Si₃-EO₈ > Cl-Si₃-EO₈ > F-Si₃-EO₈, and the adsorption efficiency ( p C₂₀), surface pressure at the CMC ( π_CMC), CMC/ C₂₀ , and A _min values increase following the order Me-Si₃-EO₈ < Cl-Si₃-EO₈ < F-Si₃-EO₈. As comparison, fluorinated trisiloxane surfactant (F-Si₃-EO₈) has greater surface activity attributed to the terminal CF₃- group. The TEM and FF-TEM results illustrated that all the investigated "linear" trisiloxane surfactants can form nonuniform size spherical aggregates.

Preparation and properties of room temperature vulcanized silicone rubber based on rosin-grafted polydimethylsiloxane

Rosin-grafted polydimethylsiloxane (RGSO) was prepared via ring-opening reaction of glycidyl ester of rosin acid (ER) with hydroxy-terminated amino polydimethylsiloxane (PDMS). The structure of RGSO was confirmed by ¹H and ¹³C NMR spectroscopy. The effects of ER on relative molecular weight and rheological properties of RGSO were studied by gel permeation chromatography and rotational rheometry. Then, room temperature vulcanized (RTV) silicone rubber modified with rosin was prepared using RGSO, hydroxy-terminated PDMS, tetraethoxysilane, and organotin catalyst. The structures and properties of RTV silicone rubbers were studied by scanning electron microscopy, thermogravimetric analysis, a universal testing machine and dynamic mechanical analysis. The rosin-modified silicone rubber showed remarkably improved thermal and mechanical properties. Temperatures corresponding to 10% weight loss and maximum rate of weight loss increased by 66 °C and 177 °C, respectively. Moreover, the tensile strength and elongation at break increased by 138% and 113%. The role of rosin structure in improvement of properties is discussed.

Rosin-grafted polydimethylsiloxane (RGSO) was prepared via ring-opening reaction of glycidyl ester of rosin acid (ER) with hydroxy-terminated amino polydimethylsiloxane (PDMS).

Thermal insulation and stability of polysiloxane foams containing hydroxyl-terminated polydimethylsiloxanes

An effective method was described here to improve the thermal insulation and stability of polysiloxane foam (SIF) by controlling the chain length of hydroxyl-terminated polydimethylsiloxane (OH-PDMS). A series of SIFs were prepared through foaming and cross-linking processes with different cross-linking densities. The morphology of SIF was investigated by environmental scanning electron microscopy. The results demonstrated that increasing the chain length of OH-PDMS reduced the average cell size from 932 μm to 220 μm. Cell density ranged from 4.92 × 10⁶ cells per cm³ to 1.64 × 10⁸ cells per cm³. The thermal insulation capability was significantly enhanced, and the SIF derived from the long-chain OH-PDMSs yielded a minimum thermal conductivity of 0.077 W mK⁻¹. Cell size reduction and an increase in cell density were considered to be the main factors to reduce thermal conductivity. Thermal stability, which was also improved, mainly depended on the free motion rate of the polysiloxane chains and cross-linking density of the polysiloxane networks.

The thermal insulation and stability of polysiloxane foam was improved by an easy operating method.