Polar phase formation in poly(vinylidene fluoride) induced by melt annealing

Anisotropic Poly(vinylidene fluoride-co-trifluoroethylene)/MXene Aerogel-Based Piezoelectric Nanogenerator for Efficient Kinetic Energy Harvesting and Self-Powered Force Sensing Applications

Lightweight flexible piezoelectric devices have garnered significant interest over the past few decades due to their applications as energy harvesters and wearable sensors. Among different piezoelectrically active polymers, poly(vinylidene fluoride) and its copolymers have attracted considerable attention for energy conversion due to their high flexibility, thermal stability, and biocompatibility. However, the orientation of polymer chains for self-poling under mild conditions is still a challenging task. Herein, anisotropic poly(vinylidene fluoride-co-trifluoroethylene) (PVDF-TrFE)/MXene aerogel-based piezoelectric generators with highly oriented MXene fillers are fabricated. The unidirectional freezing of a hybrid solution facilitates the strain-induced alignment of MXene nanosheets and polymer chains along the solvent crystal growth direction due to the robust interactions between the MXene nanosheets (O-H/F groups) and PVDF-TrFE chains (F-C/C-H groups). Consequently, this process fosters the development of abundant electroactive β crystals with preferred alignment characteristics, leading to the formation of intrinsic self-oriented dipoles within the PVDF-TrFE aerogel. As a result, the piezoelectric properties of PVDF-TrFE are fully harnessed without any complex poling process, resulting in an open-circuit voltage of around 40 V with MXene loading of 3 wt % in anisotropic aerogel, which is 2-fold higher than that of the corresponding isotropic aerogel where the MXene nanosheets and polymer chains are randomly aligned. Furthermore, the developed piezoelectric nanogenerator was demonstrated as a tactile sensor which showed a high sensitivity of 9.6 V/N for lower forces (less than 2 N) and a sensitivity of 1.3 V/N in the higher force regime (2 N < force < 10 N). The strategy adopted here not only provides the enhancement of the piezoelectric crystalline form for self-poling but also paves an avenue toward developing self-powered energy harvesters using piezoelectric polymers.

Piezoelectric PVDF and its copolymers in biomedicine: innovations and applications

In recent years, poly(vinylidene fluoride) (PVDF) has emerged as a versatile polymer with a wide range of applications across various fields. PVDF's piezosensitivity, versatility, crystalline structure, and tunable parameters have established it as a highly sought-after material. Furthermore, PVDF and its copolymers exhibit excellent processability and chemical resistance to a diverse array of substances. Of particular significance is its remarkable structural stability in physiological media, which highlights its potential for use in the development of biomedical products. This review offers a comprehensive overview of the latest advancements in PVDF-based biomedical systems. It examines the fabrication of stimulus-responsive delivery systems, bioelectric therapy devices, and tissue-regenerating scaffolds, all of which harness the piezosensitivity of PVDF. Moreover, the potential of PVDF in the fabrication of both invasive and non-invasive diagnostic tools is investigated, with particular emphasis on its flexibility, transparency, and piezoelectric efficiency. The material's high biocompatibility and physiological stability are of paramount importance in the development of implantable sensors for long-term health monitoring, which is crucial for the management of chronic diseases and postoperative care. Additionally, we discuss a novel approach to photoacoustic microscopy that employs a PVDF sensor, thereby eliminating the necessity for external contrast agents. This technique provides a new avenue for non-invasive imaging in biomedical applications. Finally, we explore the challenges and prospects for the development of PVDF-based systems for a range of biomedical applications. This review is distinctive in comparison to other reviews on PVDF due to its concentrated examination of biomedical applications, including pioneering imaging techniques, long-term health monitoring, and a detailed account of advancements in the field. Collectively, these elements illustrate the potential of PVDF to markedly influence biomedical engineering and patient care, distinguishing it from existing literature. By leveraging the distinctive attributes of PVDF and its copolymers, researchers can continue to advance the frontiers of biomedical engineering, with the potential to transform patient care and treatment outcomes.

Ingenious Structure Engineering to Enhance Piezoelectricity in Poly(vinylidene fluoride) for Biomedical Applications

The future development of wearable/implantable sensing and medical devices relies on substrates with excellent flexibility, stability, biocompatibility, and self-powered capabilities. Enhancing the energy efficiency and convenience is crucial, and converting external mechanical energy into electrical energy is a promising strategy for long-term advancement. Poly(vinylidene fluoride) (PVDF), known for its piezoelectricity, is an outstanding representative of an electroactive polymer. Ingeniously designed PVDF-based polymers have been fabricated as piezoelectric devices for various applications. Notably, the piezoelectric performance of PVDF-based platforms is determined by their structural characteristics at different scales. This Review highlights how researchers can strategically engineer structures on microscopic, mesoscopic, and macroscopic scales. We discuss advanced research on PVDF-based piezoelectric platforms with diverse structural designs in biomedical sensing, disease diagnosis, and treatment. Ultimately, we try to give perspectives for future development trends of PVDF-based piezoelectric platforms in biomedicine, providing valuable insights for further research.

Development of Highly Flexible Piezoelectric PVDF-TRFE/Reduced Graphene Oxide Doped Electrospun Nano-Fibers for Self-Powered Pressure Sensor

The demand for self-powered, flexible, and wearable electronic devices has been increasing in recent years for physiological and biomedical applications in real-time detection due to their higher flexibility and stretchability. This work fabricated a highly sensitive, self-powered wearable microdevice with Poly-Vinylidene Fluoride-Tetra Fluoroethylene (PVDF-TrFE) nano-fibers using an electrospinning technique. The dielectric response of the polymer was improved by incorporating the reduced-graphene-oxide (rGO) multi-walled carbon nano-tubes (MWCNTs) through doping. The dielectric behavior and piezoelectric effect were improved through the stretching and orientation of polymeric chains. The outermost layer was attained by chemical vapor deposition (CVD) of conductive polymer poly (3,4-ethylenedioxythiophene) to enhance the electrical conductivity and sensitivity. The hetero-structured nano-composite comprises PVDF-TrFE doped with rGO-MWCNTs over poly (3,4-ethylenedioxythiophene) (PEDOT), forming continuous self-assembly. The piezoelectric pressure sensor is capable of detecting human physiological vital signs. The pressure sensor exhibits a high-pressure sensitivity of 19.09 kPa-1, over a sensing range of 1.0 Pa to 25 kPa, and excellent cycling stability of 10,000 cycles. The study reveals that the piezoelectric pressure sensor has superior sensing performance and is capable of monitoring human vital signs, including heartbeat and wrist pulse, masticatory movement, voice recognition, and eye blinking signals. The research work demonstrates that the device could potentially eliminate metallic sensors and be used for early disease diagnosis in biomedical and personal healthcare applications.

High-Performance Piezoelectric Nanogenerator of BTO-PVDF Nanofibers for Wearable Sensing

Piezoelectric nanogenerator (PENG) produces stable electrical signals in response to external mechanical stimuli and holds promise in the fields of flexible sensors and smart wearable devices. In practice, a high-performance PENG with a straightforward structure and exceptional reliability is deeply desired. This study optimally synthesizes piezoelectric composites comprising polyvinylidene fluoride (PVDF) incorporated with barium titanate (BTO) nanoparticles (NPs) and fabricated a PENG with heightened sensitivity by using the electrospinning technique. The polar β-phase content of the dual-optimized BTO-PVDF (barium titanate and polyvinylidene fluoride) electrospun fiber reaches up to 82.39%. In the bending mode, it achieves a remarkable maximum open-circuit voltage of 19.152 V, a transferred charge of 8.058 nC, and an output voltage per unit area of 2.128 V cm- 2. Under vertical pressure conditions, the BP-PENG exhibits an impressive voltage of 12.361 V while the force is 2.156 N, demonstrating a notable pressure sensing sensitivity of 5.159 V kPa-1, with an excellent linear relationship. Furthermore, the BP-PENG displays sensitive sensing features in monitoring hand movements. The sensitive response and high performance make it promising for applications in human motion monitoring and smart wearable devices.

Piezoelectric dressings for advanced wound healing

The treatment of chronic refractory wounds poses significant challenges and threats to both human society and the economy. Existing research studies demonstrate that electrical stimulation fosters cell proliferation and migration and promotes the production of cytokines that expedites the wound healing process. Presently, clinical settings utilize electrical stimulation devices for wound treatment, but these devices often present issues such as limited portability and the necessity for frequent recharging. A cutting-edge wound dressing employing the piezoelectric effect could transform mechanical energy into electrical energy, thereby providing continuous electrical stimulation and accelerating wound healing, effectively addressing these concerns. This review primarily reviews the selection of piezoelectric materials and their application in wound dressing design, offering a succinct overview of these materials and their underlying mechanisms. This study also provides a perspective on the current limitations of piezoelectric wound dressings and the future development of multifunctional dressings harnessing the piezoelectric effect.

Review of Piezoelectric Properties and Power Output of PVDF and Copolymer-Based Piezoelectric Nanogenerators

The highest energy conversion efficiencies are typically shown by lead-containing piezoelectric materials, but the harmful environmental impacts of lead and its toxicity limit future use. At the bulk scale, lead-based piezoelectric materials have significantly higher piezoelectric properties when compared to lead-free piezoelectric materials. However, at the nanoscale, the piezoelectric properties of lead-free piezoelectric material can be significantly larger than the bulk scale. The piezoelectric properties of Poly(vinylidene fluoride) (PVDF) and Poly(vinylidene fluoride-co-trifluoroethylene) (PVDF-TrFE) lead-free piezoelectric nanomaterials are reviewed and their suitability for use in piezoelectric nanogenerators (PENGs) is determined. The impact of different PVDF/PVDF-TrFE composite structures on power output is explained. Strategies to improve the power output are given. Overall, this review finds that PVDF/PVDF-TrFE can have significantly increased piezoelectric properties at the nanoscale. However, these values are still lower than lead-free ceramics at the nanoscale. If the sole goal in developing a lead-free PENG is to maximize output power, lead-free ceramics at the nanoscale should be considered. However, lead-free ceramics are brittle, and thus encapsulation of lead-free ceramics in PVDF is a way to increase the flexibility of these PENGs. PVDF/PVDF-TrFE offers the advantage of being nontoxic and biocompatible, which is useful for many applications.

Combination NIPS/TIPS Synthesis of α-Fe2O3 and α/γ-Fe2O3 Doped PVDF Composite for Efficient Piezocatalytic Degradation of Rhodamine B

Highly porous membranes based on polyvinylidene fluoride (PVDF) with the addition of nanoscale particles of non-magnetic and magnetic iron oxides were synthesized using a combined method of non-solvent induced phase separation (NIPS) and thermo-induced phase separation (TIPS) based on the technique developed by Dr. Blade. The obtained membranes were characterized using SEM, EDS, XRD, IR, diffuse reflectance spectroscopy, and fluorescent microscopy. It was shown that the membranes possessed a high fraction of electroactive phase, which increased up to a maximum of 96% with the addition of 2 wt% of α-Fe2O3 and α/γ-Fe2O3 nanoparticles. It was demonstrated that doping PVDF with nanoparticles contributed to the reduction of pore size in the membrane. All membranes exhibited piezocatalytic activity in the degradation of Rhodamine B. The degree of degradation increased from 69% when using pure PVDF membrane to 90% when using the composite membrane. The nature of the additive did not affect the piezocatalytic activity. It was determined that the main reactive species responsible for the degradation of Rhodamine B were •OH and •O2-. It was also shown that under piezocatalytic conditions, composite membranes generated a piezopotential of approximately 2.5 V.

Flexible Self-Powered Friction Piezoelectric Sensor Based on Structured PVDF-Based Composite Nanofiber Membranes

With the rapid development of the economy and technology, intelligent wearable devices have gradually entered public life. Flexible sensors, as the main component of wearable devices, have been widely concerned. However, traditional flexible sensors need an external power supply, lacking flexibility and sustainable power supply. In this study, structured poly(vinylidene fluoride) (PVDF)-based composite nanofiber membranes doped with different mass fractions of MXene and zinc oxide (ZnO) were prepared by electrospinning and were then assembled to flexible self-powered friction piezoelectric sensors. The addition of MXene and ZnO endowed PVDF nanofiber membranes with better piezoelectric properties. The structured PVDF/MXene-PVDF/ZnO (PM/PZ) nanofiber membranes with a double-layer structure, interpenetrating structure, or core-shell structure could further enhance the piezoelectric properties of PVDF-based nanofiber membranes through the synergistic effects of filler doping and structural design. In particular, the output voltage of the self-powered friction piezoelectric sensor made of a core-shell PM/PZ nanofiber membrane showed a good linear relationship with the applied pressure and could produce a good piezoelectric response to the bending deformation caused by human motion.

Electrospun PVDF-based piezoelectric nanofibers: materials, structures, and applications

Polyvinylidene fluoride (PVDF) has been considered as a promising piezoelectric material for advanced sensing and energy storage systems because of its high dielectric constant and good electroactive response. Electrospinning is a straightforward, low cost, and scalable technology that can be used to create PVDF-based nanofibers with outstanding piezoelectric characteristics. Herein, we summarize the state-of-the-art progress on the use of filler doping and structural design to enhance the output performance of electrospun PVDF-based piezoelectric fiber films. We divide the fillers into single filler and double fillers and make comments on the effects of various dopant materials on the performance and the underlying mechanism of the PVDF-based piezoelectric fiber film. The effects of highly oriented structures, core-shell structures, and multilayer composite structures on the output properties of PVDF-based piezoelectric nanofibers are discussed in detail. Furthermore, the perspectives and opportunities for PVDF piezoelectric nanofibers in the fields of health care, environmental monitoring, and energy collection are also discussed.

Progress in Microtopography Optimization of Polymers-Based Pressure/Strain Sensors

Due to the wide application of wearable electronic devices in daily life, research into flexible electronics has become very attractive. Recently, various polymer-based sensors have emerged with great sensing performance and excellent extensibility. It is well known that different structural designs each confer their own unique, great impacts on the properties of materials. For polymer-based pressure/strain sensors, different structural designs determine different response-sensing mechanisms, thus showing their unique advantages and characteristics. This paper mainly focuses on polymer-based pressure-sensing materials applied in different microstructures and reviews their respective advantages. At the same time, polymer-based pressure sensors with different microstructures, including with respect to their working mechanisms, key parameters, and relevant operating ranges, are discussed in detail. According to the summary of its performance and mechanisms, different morphologies of microstructures can be designed for a sensor according to its performance characteristics and application scenario requirements, and the optimal structure can be adjusted by weighing and comparing sensor performances for the future. Finally, a conclusion and future perspectives are described.

Comprehensive Characterization of Solution-Cast Pristine and Reduced Graphene Oxide Composite Polyvinylidene Fluoride Films for Sensory Applications

Pristine and doped polyvinylidene fluoride (PVDF) are actively investigated for a broad range of applications in pressure sensing, energy harvesting, transducers, porous membranes, etc. There have been numerous reports on the improved piezoelectric and electric performance of PVDF-doped reduced graphene oxide (rGO) structures. However, the common in situ doping methods have proven to be expensive and less desirable. Furthermore, there is a lack of explicit extraction of the compression mode piezoelectric coefficient (d33) in ex situ rGO doped PVDF composite films prepared using low-cost, solution-cast processes. In this work, we describe an optimal procedure for preparing high-quality pristine and nano-composite PVDF films using solution-casting and thermal poling. We then verify their electromechanical properties by rigorously characterizing β-phase concentration, crystallinity, piezoelectric coefficient, dielectric permittivity, and loss tangent. We also demonstrate a novel stationary atomic force microscope (AFM) technique designed to reduce non-piezoelectric influences on the extraction of d33 in PVDF films. We then discuss the benefits of our d33 measurements technique over commercially sourced piezometers and conventional piezoforce microscopy (PFM). Characterization outcomes from our in-house synthesized films demonstrate that the introduction of 0.3%w.t. rGO nanoparticles in a solution-cast only marginally changes the β-phase concentration from 83.7% to 81.7% and decreases the crystallinity from 42.4% to 37.3%, whereas doping increases the piezoelectric coefficient by 28% from d33 = 45 pm/V to d33 = 58 pm/V, while also improving the dielectric by 28%. The piezoelectric coefficients of our films were generally higher but comparable to other in situ prepared PVDF/rGO composite films, while the dielectric permittivity and β-phase concentrations were found to be lower.

Poly(vinylidene fluoride) Intestinal Sleeve Implants for the Treatment of Obesity and Type 2 Diabetes

Currently, treatment of diabetes and associated obesity involves Roux-en-Y gastric bypass or sleeve gastrectomy to reduce the absorption of nutrients from the intestine to achieve blood glucose control. However, the surgical procedure and subsequent recovery are physically and psychologically burdensome for patients, with possible side effects, so alternative treatments are being developed. In this study, two methods, solution casting and machine direction orientation (MDO), were used to prepare intestinal implants made of poly(vinylidene fluoride) (PVDF) film and implant them into the duodenum of type 2 diabetic rats for the treatment of obesity and blood glucose control. The PVDF film obtained by the MDO process was characterized by FT-IR, Raman spectroscopy, XRD and piezoelectricity tests, which showed higher composition of β crystalline phase and better elongation and mechanical strength in specific directions. Therefore, the material was finally tested on rats after it was proven to be non-toxic by biological toxicity tests. The PVDF was implanted into alloxan-induced diabetic rats, which were used as a model of impaired insulin secretion due to pancreatic beta cell destruction rather than obesity-induced diabetes, and rats were tracked for 24 days, showing significantly improved body weight and blood glucose levels. As an alternative therapeutic option, intestinal sleeve implant showed future potential for application.

Fabrication of β-Phase-Enriched PVDF Sheets for Self-Powered Piezoelectric Sensing

The fabrication of self-powered pressure sensors based on piezoelectric materials requires flexible piezoelectric generators produced with a continuous, large-scale, and environmentally friendly approach. In this study, continuous poly(vinylidene fluoride) (PVDF) sheets with a higher β-phase content were facilely fabricated by the melt-extrusion-calendering technique and a PVDF-based piezoelectric generator (PEG) was further assembled. Such a PEG exhibits a remarkable piezoelectric output performance. Moreover, it possesses prominent stability even after working for a long time, exhibiting potential applications for real-time monitoring of various human movements (i.e., hopping, running, and walking) and gait. This work not only provides the possibility of continuous and environmentally friendly fabrication of PVDF sheets with remarkable piezoelectric properties but also paves a new promising pathway for powering portable microelectronic applications without any external power supply.

In Vitro Cell Interactions on PVDF Films: Effects of Surface Morphology and Polar Phase Transition

In recent years, several studies have validated the use of piezoelectric materials for in situ biological stimulation, opening new interesting insights for bio-electric therapies. In this work, we investigate the morphological properties of polyvinylidene fluoride (PVDF) in the form of microstructured films after temperature-driven phase transition. The work aims to investigate the correlations between morphology at micrometric (i.e., spherulite size) and sub-micrometric (i.e., phase crystallinity) scale and in vitro cell response to validate their use as bio-functional interfaces for cellular studies. Morphological analyses (SEM, AFM) enabled evidence of the peculiar spherulite-like structure and the dependence of surface properties (i.e., intra-/interdomain roughness) upon process conditions (i.e., temperature). Meanwhile, chemical (i.e., FTIR) and thermal (i.e., DSC) analyses highlighted an influence of casting temperature and polymer solution on apolar to polar phases transition, thus affecting in vitro cell response. Accordingly, in vitro tests confirmed the relationship between micro/sub-microstructural properties and hMSC response in terms of adhesion and viability, thus suggesting a promising use of PVDF films to model, in perspective, in vitro functionalities of cells under electrical stimuli upon mechanical solicitation.

Piezoelectric Materials for Energy Harvesting and Sensing Applications: Roadmap for Future Smart Materials

Piezoelectric materials are widely referred to as "smart" materials because they can transduce mechanical pressure acting on them to electrical signals and vice versa. They are extensively utilized in harvesting mechanical energy from vibrations, human motion, mechanical loads, etc., and converting them into electrical energy for low power devices. Piezoelectric transduction offers high scalability, simple device designs, and high-power densities compared to electro-magnetic/static and triboelectric transducers. This review aims to give a holistic overview of recent developments in piezoelectric nanostructured materials, polymers, polymer nanocomposites, and piezoelectric films for implementation in energy harvesting. The progress in fabrication techniques, morphology, piezoelectric properties, energy harvesting performance, and underpinning fundamental mechanisms for each class of materials, including polymer nanocomposites using conducting, non-conducting, and hybrid fillers are discussed. The emergent application horizon of piezoelectric energy harvesters particularly for wireless devices and self-powered sensors is highlighted, and the current challenges and future prospects are critically discussed.

Crystallinity and β Phase Fraction of PVDF in Biaxially Stretched PVDF/PMMA Films

Polyvinylidene fluoride (PVDF) and poly(methyl methacrylate) (PMMA) blend films were prepared using biaxial stretching. The effects of PMMA content and stretching ratio on the crystallinity and β phase fraction of PVDF in blend films were investigated. The distributions of crystallinity and β phase fraction on variable locations were also studied. The results of FTIR and XRD showed that β phase appeared in PVDF/PMMA blends after extrusion and casting procedures. Although β phase fraction decreased after preheating, there was still an increasing trend during following biaxial stretching. More importantly, the increase in PMMA content improved β phase fraction, and the highest β phase fraction of 93% was achieved at PMMA content of 30 wt% and stretching ratio of 2×2. Besides, the reduction in PMMA content and the increase in stretching ratio improved the crystallinity of PVDF. The mechanical properties of the stretched films were significantly improved by increasing the stretching ratio as well. The uniform stress distribution on different regions of biaxial stretching films contributed to the uniform distribution of β phase fraction and crystallinity of PVDF with the aid of simulation. This work confirmed that biaxial stretching can be a candidate method to prepare PVDF/PMMA blend films with uniform distributions of comparable β phase and crystallinity of PVDF.

Interfacial Nanostructuring of Poly(vinylidene fluoride) Homopolymer with Predominant Ferroelectric Phases

Facile preparation of poly(vinylidene fluoride) (PVDF) homopolymer nanoparticles (NPs) with monodispersed size distribution and predominant ferroelectric phases was done in an interfacial nonsolvent (water/methanol)-solvent (dimethylformamide (DMF))-polymer (PVDF) ternary system using two interfacial nanoassembly methods. First, a fluidic liquid-liquid interface consisting of two miscible solvents was created by introducing nonsolvent (water) under the PVDF solution. After the interface was created, the interface moved up to the DMF phase direction; PVDF NPs were produced through nonsolvent-induced phase separation. As the water content decreased in the nonsolvent by mixing with methanol, PVDF structures changed from nanoparticles with 252 nm average diameter (PVDF NP-1) to a porous membrane through membrane-wrapped NPs. The phenomena were found to be related to the mutual affinity of solvent, nonsolvent, and PVDF. When an additional external force was introduced to the water-DMF-PVDF system through magnetic stirring (reprecipitation method), smaller PVDF NPs with 61.4 nm diameter were obtained (PVDF NP-2). Both the as-prepared PVDF NPs were demonstrated with the predominant ferroelectric (electroactive (EA)) phase up to 97-98% among crystalline phases, which is apparently the highest value ever reported for PVDF homopolymer NPs. It is noteworthy that PVDF NP-2 showed a higher β phase ratio than that of PVDF NP-1, as proved using Fourier transform infrared (FT-IR) spectroscopy. Also, differential scanning calorimetry (DSC) and X-ray diffraction (XRD) measurements revealed that PVDF NP-1 exhibited higher crystallinity and that PVDF NP-2 underwent a well-separated two-step phase transition under heating. Results suggest that controlling interface formation with DMF and water plays a crucial role in manipulating ferroelectric PVDF nanostructures in terms of crystallinity and the ferroelectric β phase-to-γ phase ratio.

Cellular Polyolefin Composites as Piezoelectric Materials: Properties and Applications

Piezoelectric polymers characterized by flexibility are sought for applications in microelectronics, medicine, telecommunications, and everyday devices. The objective of this work was to obtain piezoelectric polymeric composites with a cellular structure and to evaluate their usefulness in practice. Composites based on polyolefins (isotactic-polypropylene and polyethylene) with the addition of aluminosilicate fillers were manufactured by extrusion, and then polarized in a constant electric field at 100 V/µm. The content of mineral fillers up to 10 wt% in the polymer matrix enhances its electric stability and mechanical strength. The value of the piezoelectric coefficient d₃₃ attained ~150 pC/N in the range of lower stresses and ~80 pC/N in the range of higher stresses, i.e., at ~120 kPa. The materials exhibited high durability in time, therefore, they can be used as transducers of mechanical energy of the human motion into electric energy. It was demonstrated that one shoe insert generates an energy of 1.1 mJ after a person walks for 300 s. The miniaturized integrated circuits based on polyolefin composites may be applied for the power supply of portable electronics. Due to their high sensitivity, they can be recommended for measuring the blood pulse.

Using Annealing Treatment on Fabrication Ionic Liquid-Based PVDF Films

In this study, a simple method to obtain pure β-phase directly from the melt process is proposed. A series of PVDF and ionic liquid (IL) was prepared by a solvent casting method with appropriate associated with the subsequent annealing treatment. IL plays a role of filler, which can create strong electrostatic interaction with PVDF matrix and directly induce β-phase crystallization on the PVDF during the melt. PVDF film sample is immersed in hot water for annealing treatment at different temperatures (25 °C to 70 °C). We found that annealing in high temperatures especially can not only increase more IL inserted into the amorphous region of polymer matrix to make more phase transformation, but also accelerate IL removal. Characteristics and performance of the PVDF films were investigated by use of FTIR, XRD, SEM, and AFM. Piezoelectric coefficient d33 as well as d31, degree of crystallinity, and sensitivity are measured in experiment to verify the performance of PVDF film.

Polar crystalline phases of PVDF induced by interaction with functionalized boron nitride nanosheets

The PVDF/OH-BNNS nanocomposites mainly form a non-polar phase, while polar crystalline phases are the majority in the PVDF/NH₂-BNNS nanocomposites.

Improved battery performance contributed by the optimized phase ratio of β and α of PVDF

Inorganic salts (LiCl) were induced to improve the ratio of β and α of PVDF by the solution method. The vibrational spectra of PVDF polymorphic polymers were obtained by Fourier transform infrared spectroscopy (FTIR), and the results showed that the ratio of β and α of pristine PVDF was elevated from 43.66% to 53.27%. A small amount of LiCl grains was detected to be decorated on the surface of LiCl-involved electrodes by the SEM and EDS tests. The rate capability of the modified samples was evaluated when charge-discharged at 5C. The capacity of the 1/10LiCl@PVDF samples remained at a high level of 71.64% when charge-discharged at 5C, which was much higher than the value of 54.66% for pristine samples. The results of the CV and EIS tests revealed that the electrochemical polarization increasing rate and charge transfer resistance of the 1/10LiCl@PVDF samples were smaller than those of the pristine PVDF samples.

Inorganic salts (LiCl) were induced to improve the ratio of β and α of PVDF by the solution method.

Properties and Applications of the β Phase Poly(vinylidene fluoride)

Poly(vinylidene fluoride), PVDF, as one of important polymeric materials with extensively scientific interests and technological applications, shows five crystalline polymorphs with α, β, γ, δ and ε phases obtained by different processing methods. Among them, β phase PVDF presents outstanding electrical characteristics including piezo-, pyro-and ferroelectric properties. These electroactive properties are increasingly important in applications such as energy storage, spin valve devices, biomedicine, sensors and smart scaffolds. This article discusses the basic knowledge and character methods for PVDF fabrication and provides an overview of recent advances on the phase modification and recent applications of the β phase PVDF are reported. This study may provide an insight for the development and utilization for β phase PVDF nanofilms in future electronics.

Tactile-Sensing Based on Flexible PVDF Nanofibers via Electrospinning: A Review

The flexible tactile sensor has attracted widespread attention because of its great flexibility, high sensitivity, and large workable range. It can be integrated into clothing, electronic skin, or mounted on to human skin. Various nanostructured materials and nanocomposites with high flexibility and electrical performance have been widely utilized as functional materials in flexible tactile sensors. Polymer nanomaterials, representing the most promising materials, especially polyvinylidene fluoride (PVDF), PVDF co-polymer and their nanocomposites with ultra-sensitivity, high deformability, outstanding chemical resistance, high thermal stability and low permittivity, can meet the flexibility requirements for dynamic tactile sensing in wearable electronics. Electrospinning has been recognized as an excellent straightforward and versatile technique for preparing nanofiber materials. This review will present a brief overview of the recent advances in PVDF nanofibers by electrospinning for flexible tactile sensor applications. PVDF, PVDF co-polymers and their nanocomposites have been successfully formed as ultrafine nanofibers, even as randomly oriented PVDF nanofibers by electrospinning. These nanofibers used as the functional layers in flexible tactile sensors have been reviewed briefly in this paper. The β-phase content, which is the strongest polar moment contributing to piezoelectric properties among all the crystalline phases of PVDF, can be improved by adjusting the technical parameters in electrospun PVDF process. The piezoelectric properties and the sensibility for the pressure sensor are improved greatly when the PVDF fibers become more oriented. The tactile performance of PVDF composite nanofibers can be further promoted by doping with nanofillers and nanoclay. Electrospun P(VDF-TrFE) nanofiber mats used for the 3D pressure sensor achieved excellent sensitivity, even at 0.1 Pa. The most significant enhancement is that the aligned electrospun core-shell P(VDF-TrFE) nanofibers exhibited almost 40 times higher sensitivity than that of pressure sensor based on thin-film PVDF.

A critical analysis of the α, β and γ phases in poly(vinylidene fluoride) using FTIR

A universal but simple procedure for identifying the α, β and γ phases in PVDF using FTIR is proposed and validated. An integrated quantification methodology for individual β and γ phase in mixed systems is also proposed.

Crystallographic features of poly(vinylidene fluoride) film upon an attractive substrate of KBr

Among all the polymorphs of poly(vinylidene fluoride) (PVDF), the polar γ-form possesses the highest melting point and electrical breakdown strength as well as the strongest solvent and irradiation resistance, which are beneficial for the durability of PVDF products.

Induced formation of dominating polar phases of poly(vinylidene fluoride): positive ion-CF2 dipole or negative ion-CH2 dipole interaction

The "ion-dipole" interaction has been the most widely accepted mechanism for the direct formation of polar phases (β, γ) of poly(vinylidene fluoride) (PVDF), which have been widely used as transducers, actuators, and sensors. However, the type of charged ions is still controversial. In order to throw light upon this issue, two types of charged small organic molecules that are in different physical states (melt or solid) during the crystallization of PVDF were melt-blended with PVDF resin. Results revealed that only the incorporation of positive charged molecules can lead to the formation of polar phases. Additionally, it is interesting to find that during the crystallization of PVDF, molten positively charged molecules resulted in β-phase dominating, while solid positively charged molecules exclusively induced γ-phase. These results lead to the understanding that the induced formation of polar phases of PVDF is due to the "positive ion-CF2 dipole" interaction.