Evaluation of demineralized dentin contraction by stereo measurements using environmental and conventional scanning electron microscopy

Morphological/chemical imaging of demineralized dentin layer in its natural, wet state

OBJECTIVE

Measuring the structure, composition or suitability for bonding of the acid-etched dentin substrate, especially in its hydrated state, has been a formidable problem. The purpose of this study was to determine the morphological and structural profiles of the dentin demineralized layer measured in its natural wet state using environmental scanning electron microscopy (ESEM) and micro-Raman imaging.

MATERIALS AND METHODS

The occlusal 1/3 of the crown was removed from nine extracted, unerupted human third molars. Dentin surfaces were abraded with 600-grit SiC sandpaper under water to create smear layers. The prepared dentin surfaces were randomly selected for treatment with the self-etching agent (Adper Prompt L-Pop) or the total-etching agent 35% H(3)PO(4) gel (with/without agitation). Micro-Raman spectra and imaging were acquired at 1-1.5microm spatial resolution at positions perpendicular to the treated surfaces; since this technique is non-destructive, the same specimens were also imaged with ESEM. Specimens were kept wet throughout spectral acquisition and ESEM observations.

RESULTS

ESEM could be used to reveal demineralized layers in acid-etched dentin, but the resolution was low and no collagen fibrils were disclosed. The detailed chemical maps/profiles of demineralized dentin layers under wet conditions could be obtained using Raman imaging. It was shown that the mineral existed in the superficial layer of all etched dentin covered with smear layers. The mineral was much easier to be removed underneath the superficial layer. The depth, degree, and profile of dentin demineralization were dependent on the types of acids (self-etching vs. total etching) and application procedures (with vs. without agitation).

SIGNIFICANCE

Most current adhesives are applied using wet bonding techniques in which the dentin is kept fully hydrated throughout the bonding. Our ability to fully characterize the hydrated, etched dentin substrates is very important for understanding bonding under in vivo conditions.

A novel real-time confocal imaging technique for examining host–implant interfacial shear failure patterns

In clinical practice, implant failure usually occurs at the biomaterial-host tissue interface, typically involving both biomechanical and biochemical mechanisms. By definition, any new 'bioactive' material will bond to living bone but, prior to clinical use, interface formation, performance, longevity and failure pattern characterizations are necessary. The common missing link in many biomaterial interface investigations is imaging at the point of presumed loaded failure. The novel real-time confocal technique described here allows bond strength, formation rate, longevity and bone-material interface failure pattern characterization for a wide range of biomaterials capable of forming tissue interfaces, in one real-time imaged microshear stress process, conducted using imaging frame matched load/displacement data acquisition under relatively normal near in vivo environmental conditions. The technique, validated by post-failure scanning electron microscopy imaging, revealed that more slowly reacting melt-derived 45S5 glass materials produced stronger and more stable long-term interfaces than faster reacting microporous bioactive sol-gel glasses.

A vision-based, 3D reconstruction technique for scanning electron microscopy: Direct comparison with atomic force microscopy

High-resolution, detailed 3D reconstructions of biological specimens obtained from scanning electron microscopy stereo-micrographs and proprietary software were compared with Tapping-Mode AFM datasets of the same fields. The reconstruction software implements several original solutions including a neural adaptive point-matching technique, the ability to build an irregular triangulated mesh rather than a regular orthogonal grid, and the ability to re-map one of the original images exactly onto the reconstructed surface. The technique was applied to human nerve tissue to obtain 1,424 x 968-pixel, texture-mapped datasets, which were subsequently compared against 512 x 512-pixel AFM datasets from the same viewfields. Accounting for the inherent differences of the two techniques, direct comparison revealed an excellent visual match. The correspondence was also quantified by calculating the cross-correlation coefficient between corresponding altimetric profiles in SEM and AFM data, which consistently exceeded a figure of 0.9, with a rate of point mismatch in the order of 0.01%. Research is still underway to improve the robustness of the technique when applied to arbitrary images