Adsorption of benzotriazole on copper surfaces in a hydrochloric acid solution

Chemical, electrochemical, and quantum investigation into the use of an organophosphorus derivative to inhibit copper corrosion in acidic environments

In order to protect the copper against corrosion, a novel corrosion inhibitor known as diphenyl ((2-aminoethyl) amino) (4-methoxyphenyl) methyl) phosphonate (DAMP) was developed. Acid solutions of HCl and H2SO4 were the aggressive solutions employed in this study. Analysis using the FT-IR, 1H-NMR, 31P-NMR, 13C-NMR and BET confirmed that the DAMP was successfully synthesized. The anti-corrosion capabilities of DAMP are evaluated using a combination of chemical, electrochemical and quantum studies. The DAMP has been found to be crucial in preventing the corrosion of copper in both HCl and H2SO4 acid. This was obviously implied by the observation that the corrosion rate of copper in acid solutions decreased when DAMP was added. It is significant to note that 180 ppm produced the highest levels of inhibiting efficiency (96.6% for HCl and 95.2% for H2SO4). The tendency of DAMP to adsorb on the surface of copper through its hetero-atoms (O, N, and P) is the main factor for the anti-corrosion capabilities of DAMP. Results from SEM/EDX tests supported this. The actual adsorption takes place via various active centers, physical and chemical mechanisms that are coordinated with the estimated quantum parameters. Additionally, the adsorption of DAMP adheres to the Langmuir isotherm.

Effects of thermal treatments on protein adsorption of Co-Cr-Mo ASTM-F75 alloys

Post-manufacturing thermal treatments are commonly employed in the production of hip replacements to reduce shrinkage voids which can occur in cast components. Several studies have investigated the consequences of these treatments upon the alloy microstructure and tribological properties but none have determined if there are any biological ramifications. In this study the adsorption of proteins from foetal bovine serum (FBS) on three Co-Cr-Mo ASTM-F75 alloy samples with different metallurgical histories, has been studied as a function of protein concentration. Adsorption isotherms have been plotted using the surface concentration of nitrogen as a diagnostic of protein uptake as measured by X-ray photoelectron spectroscopy. The data was a good fit to the Langmuir adsorption isotherm up to the concentration at which critical protein saturation occurred. Differences in protein adsorption on each alloy have been observed. This suggests that development of the tissue/implant interface, although similar, may differ between as-cast (AC) and heat treated samples.

Density functional theory study of ATA, BTAH, and BTAOH as copper corrosion inhibitors: adsorption onto Cu(111) from gas phase

A low-coverage gas-phase adsorption of three corrosion inhibitors-3-amino-1,2,4-triazole (ATA), benzotriazole (BTAH), and 1-hydroxybenzotriazole (BTAOH)-on perfect Cu(111) surface has been studied and characterized using density functional theory calculations. We find that the molecules in neutral form chemisorb weakly to the perfect surface in an upright geometry. The strength of the chemisorption increases in the order BTAH < BTAOH < ATA with adsorption energies of -0.40, -0.53, and -0.60 eV, respectively. The molecules bond to the surface with triazole nitrogen atoms and also through X-H···Metal hydrogen bonds (X = N or O). In addition to chemisorption, BTAH and BTAOH can also physisorb with the molecular plane being nearly parallel to the surface and the energies of the physisorption are -0.72 and -0.97 eV, respectively, hence being more exothermic than the corresponding chemisorption energies. On the other hand, the molecules in dehydrogenated form chemisorb strongly to the surface and the strength of the chemisorption increases in the order BTAO· < ATA· < BTA· with the adsorption energies of -1.65, -2.22, and -2.78 eV, respectively. This order is compatible with the trend of experimentally observed corrosion inhibition effectiveness on copper in near-neutral chloride solutions. Although the calculations are performed at the metal/vacuum interface, they provide enough insight to rationalize why in some experiments the BTAH was observed to be adsorbed with an upright geometry and in the others with parallel geometry.