High Capacity Electrospun MgFe 2 O 4 –C Composite Nanofibers as an Anode Material for Lithium Ion Batteries

Carbon-coated Ni0.5Mg0.5Fe1.7Mn0.3O4 nanoparticles as a novel anode material for high energy density lithium-ion batteries

Lithium-ion batteries (LIBs) have gained considerable attention from the scientific community due to their outstanding properties, such as high energy density, low self-discharge, and environmental sustainability. Among the prominent candidates for anode materials in next-generation LIBs are the spinel ferrites, represented by the MFe2O4 series, which offer exceptional theoretical capacities, excellent reversibility, cost-effectiveness, and eco-friendliness. In the scope of this study, Ni0.5Mg0.5Fe1.7Mn0.3O4 nanoparticles were synthesized using a sol-gel synthesis method and subsequently coated with a carbon layer to further enhance their electrochemical performance. TEM images confirmed the presence of the carbon coating layer on the Ni0.5Mg0.5Fe1.7Mn0.3O4/C composite. The analysis of the measured X-ray diffraction (XRD) and Raman spectroscopy results confirmed the formation of nanocrystalline Ni0.5Mg0.5Fe1.7Mn0.3O4 before coating and amorphous carbon in the Ni0.5Mg0.5Fe1.7Mn0.3O4/C after the coating. The Ni0.5Mg0.5Fe1.7Mn0.3O4 anode material exhibited a much higher specific capacity than the traditional graphite material, with initial discharge/charge capacities of 1275 and 874 mA h g-1, respectively, at a 100 mA g-1 current density and a first coulombic efficiency of 68.54%. The long-term cycling test showed a slight capacity fading, retaining approximately 85% of its initial capacity after 75 cycles. Notably, the carbon-coating layer greatly enhanced the stability and slightly increased the capacity of the as-prepared Ni0.5Mg0.5Fe1.7Mn0.3O4. The first discharge/charge capacities of Ni0.5Mg0.5Fe1.7Mn0.3O4/C at 100 mA g-1 current density reached 1032 and 723 mA h g-1, respectively, and a first coulombic efficiency of 70.06%, with an increase of discharge/charge capacities to 826.6 and 806.2 mA h g-1, respectively, after 75 cycles (with a capacity retention of 89.7%), and a high-rate capability of 372 mA h g-1 at 2C. Additionally, a full cell was designed using a Ni0.5Mg0.5Fe1.7Mn0.3O4/C anode and an NMC811 cathode. The output voltage was about 2.8 V, with a high initial specific capacity of 755 mA h g-1 at 0.125C, a high rate-capability of 448 mA h g-1 at 2C, and a high-capacity retention of 91% after 30 cycles at 2C. The carbon coating layer on Ni0.5Mg0.5Fe1.7Mn0.3O4 nanoparticles played a crucial role in the excellent electrochemical performance, providing conducting, buffering, and protective effects.

MgFe2O4@Tris magnetic nanoparticles: an effective and powerful catalyst for one-pot synthesis of pyrazolopyranopyrimidine and tetrahydrodipyrazolopyridine derivatives

Magnesium (Mg) as a metal has wide applications, but its use in chemical reactions is rarely reported. Currently, magnesium catalytic processes are being developed to synthesize basic chemical compounds. Therefore, an effective and recyclable nano-catalyst was synthesized using MgFe2O4@Tris in this study. The structure of MgFe2O4@Tris was characterized by various techniques including Fourier-transform infrared (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray (EDX), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and vibrating sample magnetometer (VSM) techniques. Finally, the catalytic activity of this nano-catalyst was evaluated for the synthesis of pyrazolopyranopyrimidine and tetrahydrodipyrazolopyridine derivatives. Among the advantages of this catalyst are its high catalytic activity, high yields, use of environmentally friendly solvents, easy magnetic separation, and the possibility of reusing the catalyst.

Flexible electrodes with high areal capacity based on electrospun fiber mats

The ever-growing portable, flexible, and wearable devices impose new requirements from power sources. In contrast to gravitational metrics, areal metrics are more reliable performance indicators of energy storage systems for portable and wearable devices. For energy storage devices with high areal metrics, a high mass loading of the active species is generally required, which imposes formidable challenges on the current electrode fabrication technology. In this regard, integrated electrodes made by electrospinning technology have attracted increasing attention due to their high controllability, excellent mechanical strength, and flexibility. In addition, electrospun electrodes avoid the use of current collectors, conductive additives, and polymer binders, which can essentially increase the content of the active species in the electrodes as well as reduce the unnecessary physically contacted interfaces. In this review, the electrospinning technology for fabricating flexible and high areal capacity electrodes is first highlighted by comparing with the typical methods for this purpose. Then, the principles of electrospinning technology and the recent progress of electrospun electrodes with high areal capacity and flexibility are elaborately discussed. Finally, we address the future perspectives for the construction of high areal capacity electrodes using electrospinning technology to meet the increasing demands of flexible energy storage systems.

A Review of Recent Advancements in Electrospun Anode Materials to Improve Rechargeable Lithium Battery Performance

Although lithium-ion batteries have already had a considerable impact on making our lives smarter, healthier, and cleaner by powering smartphones, wearable devices, and electric vehicles, demands for significant improvement in battery performance have grown with the continuous development of electronic devices. Developing novel anode materials offers one of the most promising routes to meet these demands and to resolve issues present in existing graphite anodes, such as a low theoretical capacity and poor rate capabilities. Significant improvements over current commercial batteries have been identified using the electrospinning process, owing to a simple processing technique and a wide variety of electrospinnable materials. It is important to understand previous work on nanofiber anode materials to establish strategies that encourage the implementation of current technological developments into commercial lithium-ion battery production, and to advance the design of novel nanofiber anode materials that will be used in the next-generation of batteries. This review identifies previous research into electrospun nanofiber anode materials based on the type of electrochemical reactions present and provides insights that can be used to improve conventional lithium-ion battery performances and to pioneer novel manufacturing routes that can successfully produce the next generation of batteries.

Spinel ferrite (AFe2O4)-based heterostructured designs for lithium-ion battery, environmental monitoring, and biomedical applications

The development of spinel ferrite nanomaterial (SFN)-based hybrid architectures has become more popular owing to the fascinating physicochemical properties of SFNs, such as their good electro-optical and catalytic properties, high chemothermal stability, ease of functionalization, and superparamagnetic behaviour. Furthermore, achieving the perfect combination of SFNs and different nanomaterials has promised to open up many unique synergistic effects and advantages. Inspired by the above-mentioned noteworthy properties, numerous and varied applications have been recently developed, such as energy storage in lithium-ion batteries, environmental pollutant monitoring, and, especially, biomedical applications. In this review, recent development efforts relating to SFN-based hybrid designs are described in detail and logically, classified according to 4 major hybrid structures: SFNs/carbonaceous nanomaterials; SFNs/metal–metal oxides; SFNs/MS₂; and SFNs/other materials. The underlying advantages of the additional interactions and combinations of effects, compared to the standalone components, and the potential uses have been analyzed and assessed for each hybrid structure in relation to lithium-ion battery, environmental, and biomedical applications.

We have summarized recent developments in SFN-based hybrid designs. The additional interactions, combination effects, and important changes have been analyzed and assessed for LIB, environmental monitoring, and biomedical applications.