A Review of the Analysis of Phthalates by Gas Chromatography in Aqueous and Food Matrices

As a commonly well-known industrial chemical, phthalates are produced in high volumes to be used in various consumer products (e.g., plasticizers, medical devices, construction materials, and toys) to enhance softness, durability, transparency, and flexibility. Phthalates are generally not chemically bonded to the polymer chain of the plastic in which they are mixed. Thus, they may leach, migrate, or evaporate into indoor/outdoor air, and foodstuffs. In this review, a comprehensive overview of several sample preparation methods coupled with gas chromatography for the analysis of phthalates in various kinds of complex matrices, with a focus on the last 20 years' worth of papers. The review begins by highlighting the environmental significance of phthalate pollution along with the various routes to their exposure to general population. Then, the discussion is extended to cover the pretreatment and extraction techniques for phthalates for their quantitation based on gas chromatographic approach. Finally, the present and future challenges for the detection of phthalates in aqueous and food matrices are discussed.

Modified stainless steel wires with superwettability for highly efficient in-tube solid-phase microextraction

Construction of different surface wettability is meaningful for the interaction between the sorbent surface and target components. In the current study, four kinds of stainless-steel wires (SSWs) with different hydrophobic/hydrophilic property were prepared and used as the absorbents to enrich the target compounds with different polarity. Comparative extraction of six non-polar polycyclic aromatic hydrocarbons (PAHs) and six polar estrogens was carried out by in-tube solid phase microextraction (IT-SPME). The results showed that two SSWs with the superhydrophobic surfaces exhibited high extraction capacity to the non-polar PAHs with the superior enrichment factor (EF) in the range of 29-672 and 57-744, respectively. In contrast, the superhydrophilic SSWs demonstrated higher enrichment efficiency for the polar estrogens than other hydrophobic SSWs. On the basis of optimized conditions, a validated analysis method was established using six PAHs as model analytes for IT-SPME-HPLC. Acceptable linear ranges (0.5-10 μg L^-1) and low detection limits (0.0056-0.32 μg L^-1) were achieved using the superhydrophobic wire modified by perfluorooctyl trichlorosilane (FOTS). The relative recoveries spiked at 2, 5 and 10 μg L^-1 in the lake water samples were in the range of 81.5%-113.7%. The relative standard deviation (RSD) of intraday (≤0.8%, n = 3) and interday (≤5.3%, n = 3) tests demonstrated the good extraction repeatability for the same extraction tube. Satisfactory repeatability for the preparation of extraction tubes (n = 3) was also obtained with the RSD values in the range of 3.6%-8.0%.

In Vivo Detection of Tetrodotoxin in Takifugu obscurus Based on Solid-Phase Microextraction Coupled with Ultrahigh-Performance Liquid Chromatography-Tandem Mass Spectrometry

Pufferfish is nutritious and delicious, but the tetrodotoxin (TTX) that may exist in its body poses a serious safety hazard. It is important to use scientific and effective methods to detect the TTX in pufferfish, but most of the existing methods require complex pre-treatment steps and have sample lethality. The solid-phase microextraction (SPME) technology can be used for in vivo detection due to its advantages such as no solvent demand, simple operation, and fast detection speed. In this study, the GO-PAN@PNE SPME fibers were made via a dipping method, and their extraction effect was verified in the TTX aqueous and spiked fish. The established method has good reproducibility, and the limit of detection of TTX in pufferfish was 32 ng·g⁻¹, and the limit of quantitation was 150 ng·g⁻¹, which can meet the detection needs of pufferfish for safe consumption. This method was used to in vivo detect the Takifugu obscurus exposed to the TTX, to determine the content of TTX in the pufferfish muscle. The detection method established in this study can relatively quickly and easily realize the in vivo detection of TTX in the pufferfish, which can provide theoretical support for improvement in the food safety level of the pufferfish.

Methodology for Determining Phthalate Residues by Ultrasound–Vortex-Assisted Dispersive Liquid–Liquid Microextraction and GC-IT/MS in Hot Drink Samples by Vending Machines

In this study, a simple, fast, and effective methodology has been developed for the detection and quantification of seven phthalates potentially released in hot drinks from disposable containers used in vending machines. The authors determined the optimal conditions to be applied during the various steps of extraction of seven phthalates (DMP, DEP, DBP, DiBP, DEHP, DNOP, and DDP) from hot beverages using a model solution. The extraction and preconcentration technique used was ultrasound–vortex-assisted dispersive liquid–liquid microextraction (UVA-DLLME) followed by gas chromatographic analysis obtaining recoveries from 66.7% to 101.2% with precision and reproducibility <6.3% and <11.1%, respectively. The influence of waiting time, from the dispensing of the drink to its actual consumption, for the extraction of molecules was investigated, obtaining a temporal release profile slightly shifted towards the PAEs with higher molecular weight and vice versa for those with low molecular weight. In addition, the best instrumental parameters to be applied during the analysis of the extracts obtained were established. This optimization was carried out using GC-FID, whereas the analysis of real samples was carried out by means of GC-IT/MS for ultra-trace analysis purposes; limits of detection (LODs) ranging between 0.8 ng mL−1 and 15.4 ng mL−1 and limits of quantification (LOQs) from 1.6 ng mL−1 to 35.8 ng mL−1, both of them lower than those found by FID, were obtained.

Microextraction by packed sorbent of selected pesticides in coffee samples employing ionic liquids supported on graphene nanosheets as extraction phase

This paper describes the synthesis, characterization, and use of ionic liquids supported on silica, functionalized with graphene oxide through covalent bonding (ILz/Si@GO), as sorbents for microextraction by packed sorbent (MEPS). Seven selected pesticides (diazinon, heptachlor, aldrin, endrin, dieldrin, endosulfan, and methoxychlor), used for the prevention of pests in coffee crops, and endosulfan sulfate-an endosulfan metabolite-were selected for this study as model compounds for evaluating the sorbent performance of the synthesized materials in the MEPS device. The cycles of each of the stages were previously optimized through univariate experiments to carry out the extraction. The ILz/Si@GO phase was compared to other sorbents used in MEPS (GO, DVB-MMA, C₄/SiO₂, C₈/SiO₂, ILz/SiO₂, and bare silica) and also with graphene functionalized through other methodologies, where ILz/Si@GO showed the best results. The material was characterized using a range of techniques. The selectivity of the sorbent material and its adsorption capacity were evaluated by gas chromatography coupled with tandem mass spectrometry. The precision and accuracy of the method showed a relative standard deviation lower than 10% and recoveries from 35 to 97%. Finally, the proposed method was employed for the determination of pesticide residues in coffee samples.

Fabrication of montmorillonite/ionic liquid composite coated solid-phase microextraction fibers for determination of phenolic compounds in fruit juices by gas chromatography and liquid chromatography

Novel montmorillonite composites including ionic liquid were prepared and utilized as coating materials for solid phase microextraction fibers. Ionic liquids containing amino terminated imidazolium cations with methyl and benzyl groups and hydrophobic anions (bis(trifluoromethylsulfonyl)imide) and hydrophilic anions (bromide and tetrafluoroborate) were intercalated to KSF-montmorillonite using stainless steel wire as support by using the layer-by-layer technique. After optimization of experimental conditions, solid phase microextraction (SPME) coupled to gas chromatography/mass spectrometry (SPME-GC/MS) after derivatization by silylation and high performance liquid chromatography/diode array detector (SPME-HPLC/DAD) were developed for the determination of 16 phenolic compounds. The developed SPME-GC/MS method had wider linearity and lower limit of detection than the developed SPME-HPLC/DAD method with similar repeatability (for 5 runs, less than 4.2 %) for a single fiber. The percentage of the variance between two different fibers was less than 6.0 % in both methods. The developed SPME methods were applied successfully to fresh fruit juices and the relative recoveries and the repeatabilities from spiked fruit juice samples were satisfactorily achieved. The results obtained with both chromatographic methods were in good agreement with each other.

The Current Role of Graphene-Based Nanomaterials in the Sample Preparation Arena

Since its discovery in 2004 by Novoselov et al., graphene has attracted increasing attention in the scientific community due to its excellent physical and chemical properties, such as thermal/mechanical resistance, electronic stability, high Young's modulus, and fast mobility of charged atoms. In addition, other remarkable characteristics support its use in analytical chemistry, especially as sorbent. For these reasons, graphene-based materials (GBMs) have been used as a promising material in sample preparation. Graphene and graphene oxide, owing to their excellent physical and chemical properties as a large surface area, good mechanical strength, thermal stability, and delocalized π-electrons, are ideal sorbents, especially for molecules containing aromatic rings. They have been used in several sample preparation techniques such as solid-phase extraction (SPE), stir bar sorptive extraction (SBSE), magnetic solid-phase extraction (MSPE), as well as in miniaturized modes as solid-phase microextraction (SPME) in their different configurations. However, the reduced size and weight of graphene sheets can limit their use since they commonly aggregate to each other, causing clogging in high-pressure extractive devices. One way to overcome it and other drawbacks consists of covalently attaching the graphene sheets to support materials (e.g., silica, polymers, and magnetically modified supports). Also, graphene-based materials can be further chemically modified to favor some interactions with specific analytes, resulting in more efficient hybrid sorbents with higher selectivity for specific chemical classes. As a result of this wide variety of graphene-based sorbents, several studies have shown the current potential of applying GBMs in different fields such as food, biological, pharmaceutical, and environmental applications. Within such a context, this review will focus on the last five years of achievements in graphene-based materials for sample preparation techniques highlighting their synthesis, chemical structure, and potential application for the extraction of target analytes in different complex matrices.

Role of Ionic Liquids in Composites in Analytical Sample Preparation

Ionic liquids (ILs) are a group of non-conventional salts with melting points below 100 °C. Apart from their negligible vapor pressure at room temperature, high thermal stability, and impressive solvation properties, ILs are characterized by their tunability. Given such nearly infinite combinations of cations and anions, and the easy modification of their structures, ILs with specific properties can be synthesized. These characteristics have attracted attention regarding their use as extraction phases in analytical sample preparation methods, particularly in liquid-phase extraction methods. Given the liquid nature of most common ILs, their incorporation in analytical sample preparation methods using solid sorbents requires the preparation of solid derivatives, such as polymeric ILs, or the combination of ILs with other materials to prepare solid IL-based composites. In this sense, many solid composites based on ILs have been prepared with improved features, including magnetic particles, carbonaceous materials, polymers, silica materials, and metal-organic frameworks, as additional materials forming the composites. This review aims to give an overview on the preparation and applications of IL-based composites in analytical sample preparation in the period 2017–2020, paying attention to the role of the IL material in those composites to understand the effect of the individual components in the sorbent.