Superfast Synthesis of Densely Packed and Ultrafine Pt-Lanthanide@KB via Solvent-Free Microwave as Efficient Hydrogen Evolution Electrocatalysts

Revealing the mechanism of bifunctional PtLa electrocatalyst for highly efficient methanol oxidation, hydrogen evolution, and coupling reaction

The development of clean energy solutions, such as fuel cells and hydrogen energy, is crucial for addressing the global energy shortage. Platinum (Pt)-based catalysts are widely used in fuel cells and hydrogen energy generation (for example, via water electrolysis). However, reducing the amount of Pt used while maintaining the catalytic performance of such catalysts is essential. Herein, PtLa catalysts (PtxLay/C) doped with rare earth element lanthanum (La) with different Pt/La atomic ratios were synthesized using a simple chemical reduction method, resulting in Pt65La35/C, Pt78La22/C, Pt97La3/C, and Pt100/C. These PtxLay/C catalysts exhibited excellent electrocatalytic activity and stability in methanol oxidation reaction (MOR), hydrogen evolution reaction (HER), and their coupling reaction as MOR||HER under alkaline conditions. The mechanism by which La doping enhances the electrocatalytic properties and stability of Pt-based catalysts was investigated using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), aberration-corrected scanning transmission electron microscopy (AC-STEM), in-situ Fourier transform infrared (FTIR) and operando Raman spectroscopy. For HER, La doping facilitated the adsorption and activation of H2O at Pt sites, improving water dissociation and *OH desorption and reducing Pt poisoning by *OH. This enhances both the catalytic performance and stability of PtxLay/C for HER. Pt78La22/C exhibited a considerably lower overpotential of only 111 mV at 100 mA cm-2 compared to commercial 20 wt% Pt/C (Pt/C-Johnson Matthey (JM)), which requires 153 mV. For MOR, La promotes CO bond cleavage and reduces CO adsorption at the Pt sites, thereby enhancing both the performance and stability of the catalysts. The mass activity (MA) of Pt78La22/C for MOR is 4.44 A mg-1Pt, which is 12.33 times higher than that of Pt/C-JM (0.36 A/mgPt), and surpasses those of Pt65La35/C, Pt97La3/C, and Pt100/C (2.93, 0.24, and 2.91 A mg-1Pt, respectively). Additionally, Pt78La22/C exhibited outstanding catalytic performance for MOR||HER, with a current density of 20 mA cm-2 at 1.030 V, demonstrating good stability with negligible voltage changes after a 15 h chronoamperometry (CA) testing. This study provides a new strategy for synthesizing Pt-based catalysts with enhanced efficiency and low-energy input for HER||MOR.

Pt2Gd Alloy Nanoparticles from Organometallic Pt and Gd Complexes and Hollow Mesoporous Carbon Spheres: Enhanced Oxygen Reduction Reaction Activity and Durability

Pt2Gd alloy nanoparticles supported in hollow mesoporous carbon spheres (HMCS; Pt2Gd/HMCS) were successfully prepared by the thermal reduction of organometallic Pt and Gd complexes without oxygen atoms supported in the pores of HMCS. The structures of Pt2Gd alloy nanoparticles were fully characterized by TEM, HAADF-STEM-EDS, XRD, XAFS, and XPS, suggesting the formation of uniform Pt2Gd alloy nanoparticles with an average particle size of 5.9 nm. Pt2Gd/HMCS showed superior oxygen reduction reaction activity (2.4 times higher mass-specific activity to Pt nanoparticles on HMCS (Pt/HMCS)) and remarkable durability even after the 100,000 cycles of accelerated degradation tests compared to Pt/HMCS and a commercial Pt/C catalyst. The structure of the Pt2Gd alloy nanoparticles after initial aging and the durability tests suggested that the Pt2Gd core-Pt shell structure with a particle size similar to the pore size of HMCS was stably formed inside the porous structure of HMCS and maintained under the oxygen-reduction working conditions.

Lanthanide-Induced Ligand Effect to Regulate the Electronic Structure of Platinum-Lanthanide Nanoalloys for Efficient Methanol Oxidation

The ligand effect in alloy catalysts is one of the decisive parameters of the catalytic performance. However, the strong interrelation between the ligand effect and the geometric effect of the active atom and its neighbors as well as the systematic alteration of the microenvironment of the active site makes the active mechanism unclear. Herein, Pt3Tm, Pt3Yb, and Pt3Lu with a cubic crystal system (Pm-3m) were selected. With the difference of Pt-Pt interatomic distance within 0.02 Å, we minimize the geometric effect to realize the disentanglement of the system. Through precise characterization, due to the low electronegativity of Ln (Ln = Tm, Yb, and Lu) and the ligand effect in the alloy, the electronic structure of Pt is continuously optimized, which improves the electrochemical methanol oxidation reaction (MOR) performance. The Ln electronegativity has a linear relationship with the MOR performance, and Pt3Yb/C achieves a high mass activity of up to 11.61 A mgPt-1, which is the highest value reported so far in Pt-based electrocatalysts. The results obtained in this study provide fundamental insights into the mechanism of ligand effects on the enhancement of electrochemical activity in rare-earth nanoalloys.

Synthesis of Pt-Rare Earth Metal Alloys and Their Applications

The alloying of platinum (Pt) with rare earth (RE) metals has emerged as a highly promising strategy for enhancing both the activity and stability of catalysts. Consequently, the development of methods for the controlled synthesis of Pt-RE alloys has received growing attention. This review comprehensively explores diverse synthesis methodologies for Pt-RE alloys, including physical metallurgy method, chemical reduction method, electrodeposition method, and dealloying method. Additionally, this review summaries the applications of Pt-RE alloys in various fields. By providing a critical analysis of existing literature and highlighting key challenges and future directions, this review aims to offer valuable insights and serve as a springboard for further advancements in the controlled synthesis and diverse applications of Pt-RE alloys.

Synergistic reductive catalytic effects of an organic and inorganic hybrid covalent organic framework for hydrogen fuel production

Electrocatalytic hydrogen generation in alkaline medium has become widely used in a variety of sectors. However, the possibility for additional performance improvement is hampered by slow kinetics. Because of this restriction, careful control over processes such as water dissociation, hydroxyl desorption and hydrogen recombination is required. Covalent organic frameworks (COFs) based on porphyrin and polyoxometalates (POMs) show encouraging electrocatalytic performance, offering a viable route for effective and sustainable hydrogen generation. Their specific architectures lead to increased electrocatalytic activity, which makes them excellent choices for developing water electrolysis as a clean energy conversion method in the alkaline medium. In this regard, TTris@ZnPor and Lindqvist POM were coordinated to create a new eco-friendly and highly active covalent organic framework (TP@VL-COF). In order to describe TP@VL-COF, extensive structural and morphological investigations were carried out through FTIR, 1H NMR, elemental analysis, SEM, fluorescence, UV-visible, PXRD, CV, N2-adsorption isotherm, TGA and DSC analyses. In an alkaline medium, the electrocatalytic capability of 20%C/Pt, TTris@ZnPor, Lindqvist POM and TP@VL-COF was explored and compared for the hydrogen evolution reaction (HER). The TP@VL-COF showed the best catalytic efficiency for HER in an alkaline electrolyte, requiring just a 75 mV overpotential to drive 10 mA cm-2 and outperforming 20%C/Pt, TTris@ZnPor, Lindqvist POM and other reported catalysts. The Tafel slope value also indicates faster kinetics for TP@VL-COF (114 mV dec-1) than for 20%C/Pt (182 mV dec-1) TTris@ZnPor (116 mV dec-1) and Lindqvist POM (125 mV dec-1).

Activation of Ga Liquid Catalyst with Continuously Exposed Active Sites for Electrocatalytic C-N Coupling

Environmentally friendly electrocatalytic coupling of CO2 and N2 for urea synthesis is a promising strategy. However, it is still facing problems such as low yield as well as low stability. Here, a new carbon-coated liquid alloy catalyst, Ga79Cu11Mo10@C is designed for efficient electrochemical urea synthesis by activating Ga active sites. During the N2 and CO2 co-reduction process, the yield of urea reaches 28.25 mmol h-1 g-1, which is the highest yield reported so far under the same conditions, the Faraday efficiency (FE) is also as high as 60.6 % at -0.4 V vs. RHE. In addition, the catalyst shows excellent stability under 100 h of testing. Comprehensive analyses showed that sequential exposure of a high density of active sites promoted the adsorption and activation of N2 and CO2 for efficient coupling reactions. This coupling reaction occurs through a thermodynamic spontaneous reaction between *N=N* and CO to form a C-N bond. The deformability of the liquid state facilitates catalyst recovery and enhances stability and resistance to poisoning. Moreover, the introduction of Cu and Mo stimulates the Ga active sites, which successfully synthesises the *NCON* intermediate. The reaction energy barrier of the third proton-coupled electron transfer process rate-determining step (RDS) *NHCONH→*NHCONH2 was lowered, ensuring the efficient synthesis of urea.

Rare-earth Element-based Electrocatalysts Designed for CO2 Electro-reduction

Electrochemical CO2 reduction presents a promising approach for synthesizing fuels and chemical feedstocks using renewable energy sources. Although significant advancements have been made in the design of catalysts for CO2 reduction reaction (CO2RR) in recent years, the linear scaling relationship of key intermediates, selectivity, stability, and economical efficiency are still required to be improved. Rare earth (RE) elements, recognized as pivotal components in various industrial applications, have been widely used in catalysis due to their unique properties such as redox characteristics, orbital structure, oxygen affinity, large ion radius, and electronic configuration. Furthermore, RE elements could effectively modulate the adsorption strength of intermediates and provide abundant metal active sites for CO2RR. Despite their potential, there is still a shortage of comprehensive and systematic analysis of RE elements employed in the design of electrocatalysts of CO2RR. Therefore, the current approaches for the design of RE element-based electrocatalysts and their applications in CO2RR are thoroughly summarized in this review. The review starts by outlining the characteristics of CO2RR and RE elements, followed by a summary of design strategies and synthetic methods for RE element-based electrocatalysts. Finally, an overview of current limitations in research and an outline of the prospects for future investigations are proposed.

Enhanced Metal-Support Interactions Boost the Electrocatalytic Water Splitting of Supported Ruthenium Nanoparticles on a Ni3 N/NiO Heterojunction at Industrial Current Density

Developing highly efficient and stable hydrogen production catalysts for electrochemical water splitting (EWS) at industrial current densities remains a great challenge. Herein, we proposed a heterostructure-induced-strategy to optimize the metal-support interaction (MSI) and the EWS activity of Ru-Ni3 N/NiO. Density functional theory (DFT) calculations firstly predicted that the Ni3 N/NiO-heterostructures can improve the structural stability, electronic distributions, and orbital coupling of Ru-Ni3 N/NiO compared to Ru-Ni3 N and Ru-NiO, which accordingly decreases energy barriers and increases the electroactivity for EWS. As a proof-of-concept, the Ru-Ni3 N/NiO catalyst with a 2D Ni3 N/NiO-heterostructures nanosheet array, uniformly dispersed Ru nanoparticles, and strong MSI, was successfully constructed in the experiment, which exhibited excellent HER and OER activity with overpotentials of 190 mV and 385 mV at 1000 mA cm-2 , respectively. Furthermore, the Ru-Ni3 N/NiO-based EWS device can realize an industrial current density (1000 mA cm-2 ) at 1.74 V and 1.80 V under alkaline pure water and seawater conditions, respectively. Additionally, it also achieves a high durability of 1000 h (@ 500 mA cm-2 ) in alkaline pure water.

Engineering the Coordination Interface of Isolated Co Atomic Sites Anchored on N-Doped Carbon for Effective Hydrogen Evolution Reaction

The regulation of the coordination environment of the central metal atom is considered as an alternative way to enhance the performance of single-atom catalysts (SACs). Herein, we design an electrocatalyst with active sites of isolated Co atoms coordinated with four sulfur atoms supported on N-doped carbon frameworks (Co₁-S₄/NC), confirmed by high-angle annular dark-field scanning transmission electron microscope (HADDF-STEM) and synchrotron-radiation-based X-ray absorption fine structure (XAFS) spectroscopy. The Co₁-S₄/NC possesses higher hydrogen evolution reaction (HER) catalytic activity than other Co species and exceptional stability, which exhibits a small Tafel slope of 60 mV dec^-1 and a low overpotential of 114 mV at 10 mA cm^-2 during the HER in 0.5 M H₂SO₄ solution. Furthermore, through in situ X-ray absorption spectrum tests and density functional theory (DFT) calculations, we reveal the catalytic mechanism of Co₁-S₄ moieties and find that the increasing number of sulfur atoms in the Co coordination environment leads to a substantial reduction of the theoretical HER overpotential. This work may point a new direction for the synthesis, performance regulation, and practical application of single-metal-atom catalysts.

Recent development and challenges in fuel cells and water electrolyzer reactions: an overview

Water electrolysis is the most promising method for the production of large scalable hydrogen (H2), which can fulfill the global energy demand of modern society. H2-based fuel cell transportation has been operating with zero greenhouse emission to improve both indoor and outdoor air quality, in addition to the development of economically viable sustainable green energy for widespread electrochemical applications. Many countries have been eagerly focusing on the development of renewable as well as H2-based energy storage infrastructure to fulfill their growing energy demands and sustainable goals. This review article mainly discusses the development of different kinds of fuel cell electrocatalysts, and their application in H2 production through various processes (chemical, refining, and electrochemical). The fuel cell parameters such as redox properties, cost-effectiveness, ecofriendlyness, conductivity, and better electrode stability have also been highlighted. In particular, a detailed discussion has been carried out with sufficient insights into the sustainable development of future green energy economy.

Active Site Engineering in CoP@NC/Graphene Heterostructures Enabling Enhanced Hydrogen Evolution

As the core of an electrocatalyst, the active site is critical to determine its catalytic performance in the hydrogen evolution reaction (HER). In this work, porous N-doped carbon-encapsulated CoP nanoparticles on both sides of graphene (CoP@NC/GR) are derived from a bimetallic metal-organic framework (MOF)@graphene oxide composite. Through active site engineering by tailoring the environment around CoP and engineering the structure, the HER activity of CoP@NC/GR heterostructures is significantly enhanced. Both X-ray photoelectron spectroscopy (XPS) results and density functional theory (DFT) calculations manifest that the electronic structure of CoP can be modulated by the carbon matrix of NC/GR, resulting in electron redistribution and a reduction in the adsorption energy of hydrogen (ΔG_H*) from -0.53 to 0.04 eV. By engineering the sandwich-like structure, active sites in CoP@NC/GR are further increased by optimizing the Zn/Co ratio in the bimetallic MOF. Benefiting from this active site engineering, the CoP@NC/GR electrocatalyst exhibits small overpotentials of 105 mV in 0.5 M H₂SO₄ (or 125 mV in 1 M KOH) to 10 mA cm^-2, accelerated HER kinetics with a low Tafel slope of 47.5 mV dec^-1, and remarkable structural and HER stability.