Bidirectional Anions Gathering Strategy Afford Efficient Mixed PbSn Perovskite Solar Cells

Chelating Dual Interface for Efficient and Stable Crystal Growth and Iodine Defect Management in Sn-Pb Perovskite Solar Cells

Suppressing Sn2+ oxidation and rationally controlling the crystallization process of tin-lead perovskite (Sn-Pb PVK) films by suitable bonding methods have emerged as key approaches to achieving efficient and stable Sn-Pb perovskite solar cells (PSCs). Herein, the chelating coordination is performed at the top and bottom interfaces of Sn-Pb PVK films. The chelation strength is stronger toward Sn2+ than Pb2+ by introducing oligomeric proanthocyanidins (OPC) at the bottom interface. This difference in chelation strength resulted in a spontaneous gradient distribution of Sn/Pb within the perovskite layer during crystallization, particularly enhancing the enrichment of Sn2+ at the bottom interface and facilitating the extraction and separation of photogenerated charge carriers in PSCs. Simultaneously, this top-down distribution of gradually increasing Sn content slowed down the crystallization rate of Sn-Pb PVK films, forming higher-quality films. On the top interface of the PVK, trifluoroacetamidine (TFA) was used to inhibit the generation of iodine vacancies (VI) through chelating with surface-uncoordinated Pb2+/Sn2+, further passivating defects while suppressing the oxidation of Sn2+. Ultimately, the PSCs with simultaneous chelation at both top and bottom interfaces achieved a power conversion efficiency (PCE) of 23.31% and an open-circuit voltage (VOC) exceeding 0.90 V. The stability of unencapsulated target devices in different environments also improved.

Complex Metal Oxides as Emerging Inorganic Hole-Transporting Materials for Perovskite Solar Cells

Perovskite solar cells (PSCs) have achieved revolutionary progress during the past decades with a rapidly boosting rate in power conversion efficiencies from 3.8% to 26.1%. However, high-efficiency PSCs with organic hole-transporting materials (HTMs) suffer from inferior long-term stability and high costs. The replacement of organic HTMs with inorganic counterparts such as metal oxides can solve the above-mentioned problems to realize highly robust and cost-effective PSCs. Nevertheless, the widely used simple metal oxide-based HTMs are limited by the low conductivity and poor light transmittance due to the fixed atomic environment. As an emerging family of inorganic HTMs, complex metal oxides with superior structural/compositional flexibility have attracted rapidly increasing interest recently, showing superior carrier conductivity/mobility and superb light transmittance. Herein, the recent advancements in the design and development of complex metal oxide-based HTMs for high-performance PSCs are summarized by emphasizing the superiority of complex metal oxides as HTMs over simple metal oxide-based counterparts. Consequently, several distinct strategies for the design of complex metal oxide-based HTMs are proposed. Last, the future directions and remaining challenges of inorganic complex metal oxide-based HTMs for PSCs are also presented. This review aims to provide valuable guidelines for the further advancements of robust, high-efficiency, and low-cost PSCs.

Narrow Bandgap Metal Halide Perovskites for All-Perovskite Tandem Photovoltaics

All-perovskite tandem solar cells are attracting considerable interest in photovoltaics research, owing to their potential to surpass the theoretical efficiency limit of single-junction cells, in a cost-effective sustainable manner. Thanks to the bandgap-bowing effect, mixed tin-lead (Sn-Pb) perovskites possess a close to ideal narrow bandgap for constructing tandem cells, matched with wide-bandgap neat lead-based counterparts. The performance of all-perovskite tandems, however, has yet to reach its efficiency potential. One of the main obstacles that need to be overcome is the─oftentimes─low quality of the mixed Sn-Pb perovskite films, largely caused by the facile oxidation of Sn(II) to Sn(IV), as well as the difficult-to-control film crystallization dynamics. Additional detrimental imperfections are introduced in the perovskite thin film, particularly at its vulnerable surfaces, including the top and bottom interfaces as well as the grain boundaries. Due to these issues, the resultant device performance is distinctly far lower than their theoretically achievable maximum efficiency. Robust modifications and improvements to the surfaces of mixed Sn-Pb perovskite films are therefore critical for the advancement of the field. This Review describes the origins of imperfections in thin films and covers efforts made so far toward reaching a better understanding of mixed Sn-Pb perovskites, in particular with respect to surface modifications that improved the efficiency and stability of the narrow bandgap solar cells. In addition, we also outline the important issues of integrating the narrow bandgap subcells for achieving reliable and efficient all-perovskite double- and multi-junction tandems. Future work should focus on the characterization and visualization of the specific surface defects, as well as tracking their evolution under different external stimuli, guiding in turn the processing for efficient and stable single-junction and tandem solar cell devices.

Efficient All-Perovskite Tandem Solar Cells with Low-Optical-Loss Carbazolyl Interconnecting Layers

Combining wide-band gap (WBG) and narrow-band gap (NBG) perovskites with interconnecting layers (ICLs) to construct monolithic all-perovskite tandem solar cell is an effective way to achieve high power conversion efficiency (PCE). However, optical losses from ICLs need to be further reduced to leverage the full potential of all-perovskite tandem solar cells. Here, metal oxide nanocrystal layers anchored with carbazolyl hole-selective-molecules (CHs), which exhibit much lower optical loss, is employed to replace poly(3,4-ethylenedioxythiophene) polystyrenesulfonate (PEDOT : PSS) as the hole transporting layers (HTLs) in lead-tin (Pb-Sn) perovskite sub-cells and ICLs in all-perovskite tandem solar cells. Optically transparent indium tin oxide nanocrystals (ITO NCs) layers are employed to enhance anchoring of CHs, while a mixture of two CHs is adopted to tune the surface energy-levels of ITO NCs. The optimized mixed Pb-Sn NBG perovskite solar cells demonstrate a high PCE of 23.2 %, with a high short-circuit current density (Jsc ) of 33.5 mA cm-2 . A high PCE of 28.1 % is further obtained in all-perovskite tandem solar cells, with the highest Jsc of 16.7 mA cm-2 to date. Encapsulated tandem solar cells maintain 90 % of their reference point after 500 h of operation at the maximum power point (MPP) under 1-Sun illumination.