Starch-g-poly(phenyl acrylate) copolymers-synthesis, characterization, and physicochemical properties

A Zwitterionic Copolymer as Rheology Modifier and Fluid Loss Agents for Water-Based Drilling Fluids

To overcome the negative impact on the rheological and filtration loss properties of drilling fluids caused by elevated temperature and salts contamination, which are common in ultradeep or geothermal drilling operations, it is imperative to develop highly efficient additives used in the water-based drilling fluid. In this study, a zwitterionic copolymer P (AM/DMC/AMPS/DMAM, ADAD) was synthesized by using acrylamide (AM), cationic monomer methacrylatoethyl trimethyl ammonium chloride (DMC), anionic monomer 2-acrylamide-2-methyl propane sulfonic acid (AMPS), and N,N-dimethylacrylamide (DMAM) through free radical copolymerization. The copolymer was characterized by 1H Nuclear Magnetic Resonance (NMR), Fourier transform infrared spectroscopy (FTIR), elemental analysis, thermogravimetric analysis (TGA), and zeta potential. The rheological behavior, filtration properties, and the performance exposure to salt or calcium contamination in water-based drilling fluid were investigated. The bentonite/polymer suspension showed improved rheological and filtration properties even after aging at 160 °C or a high concentration of salt and calcium. The filtration loss can be greatly reduced by more than 50% (from 18 mL to 7 mL) by the inclusion of 2.0 wt% copolymer, while a slight increase in the filtrate loss was observed even when exposed to electrolyte contamination. Particle size distribution and zeta potential further validate the idea that zwitterionic copolymer can greatly improve the stability of base fluid suspension through positive group enhanced anchoring on the clay surface and repulsion force between negative particles. Moreover, this study can be directed towards the design and application of zwitterionic copolymer in a water-based drilling fluid.

The effect of the grafting percent on some of the physico-chemical and thermal properties and the decomposition course of novel starch-g-poly(cinnamyl acrylate) copolymers

This paper focuses on the chemical modification of potato starch by the cinnamyl acrylate monomer during the graft copolymerization. The maximum of the grafting percent (G) was found to be 49.2% ± 0.3 at the temperature of 65 °C for 120 min in the presence of 1.0 wt% of potassium persulfate at the starch and monomer ratio 1:2.5. The copolymers exhibited excellent resistance to polar solvents and moisture which was independent of their G values. It was due to the presence of poly(cinnamyl acrylate) chains in their structure and their very compact, non-porous structure. The chemical stability of the copolymers was dependent on the G values. The copolymers showed the highest chemical resistance to neutral and acidic environments rather than to the alkaline one. Their thermal stability was ca. 210 °C under the inert and oxidative conditions. The decomposition mechanism of the copolymers was complex and included a lot of multiple simultaneous processes combined with the emission of various volatiles. The interesting fact was that the pyrolysis of starch from the copolymers occurred before that of the grafted polymer. However, the oxidative decomposition of the grafted polymer began at lower temperatures than that of starch from the copolymers.

Development of a High-Performance Adhesive with a Microphase, Separation Crosslinking Structure Using Wheat Flour and a Hydroxymethyl Melamine Prepolymer

The objective of this study is to use wheat flour (WF) and hydroxymethyl melamine prepolymer (HMP) to develop a low cost, highly water-resistant, starch-based bio-adhesive for plywood fabrication. Three-layer plywood was fabricated using the resultant adhesive, and the wet shear strength of the plywood samples was measured under various conditions. After determining that water resistance was significantly improved with the addition of HMP, we evaluated the physical characteristics of the starch-based adhesive and functional groups and analyzed the thermal stability and fracture surface of the cured adhesive samples. Results showed that by adding 20 wt.% HMP into WF adhesive, the sedimentation volume in the resultant adhesive decreased by 11.3%, indicating that the increase of crosslinking in the structure of the adhesives increased the bond strength, and the wet shear strength of the resultant plywood in 63 °C water improved by 375% when compared with the WF adhesive. After increasing the addition of HMP to 40 wt.%, the wet shear strength of the resultant plywood in 100 °C water changed from 0 MPa to 0.71 MPa, which meets the exterior use plywood requirement. This water resistance and bond strength improvement resulted from (1) HMP reacting with functions in WF and forming a crosslinking structure to prevent moisture intrusion; and (2) HMP self-crosslinking and combining with crosslinked WF to form a microphase separation crosslinking structure, which improved both the crosslinking density and the toughness of the adhesive, and subsequently, the adhesive's bond performance. In addition, the microphase separation crosslinking structure had better thermostability and created a compact ductile fracture surface, which further improved the bond performance of the adhesive. Thus, using a prepolymer to form a microphase separation crosslinking structure within the adhesive improves the rigidity, toughness, and water resistance of the material in a practical and cost-effective manner.