Adsorption of toxic dye Eosin Y from aqueous solution by clay/carbon composite derived from spent bleaching earth

Engineering of bespoke photosensitiser-microbe interfaces for enhanced semi-artificial photosynthesis

Biohybrid systems for solar fuel production integrate artificial light-harvesting materials with biological catalysts such as microbes. In this perspective, we discuss the rational design of the abiotic-biotic interface in biohybrid systems by reviewing microbes and synthetic light-harvesting materials, as well as presenting various approaches to coupling these two components together. To maximise performance and scalability of such semi-artificial systems, we emphasise that the interfacial design requires consideration of two important aspects: attachment and electron transfer. It is our perspective that rational design of this photosensitiser-microbe interface is required for scalable solar fuel production. The design and assembly of a biohybrid with a well-defined electron transfer pathway allows mechanistic characterisation and optimisation for maximum efficiency. Introduction of additional catalysts to the system can close the redox cycle, omitting the need for sacrificial electron donors. Studies that electronically couple light-harvesters to well-defined biological entities, such as emerging photosensitiser-enzyme hybrids, provide valuable knowledge for the strategic design of whole-cell biohybrids. Exploring the interactions between light-harvesters and redox proteins can guide coupling strategies when translated into larger, more complex microbial systems.

Preparation and application of the thermo-/pH-/ ion-sensitive semi-IPN hydrogel based on chitosan

Chitosan based hydrogels with multiple stimulus responses have broad application prospects in many fields. Considering the advantages of semi interpenetrating network (IPN) technology and the special temperature and ion responsiveness of polymers containing zwitterionic groups, a semi-IPN hydrogel was prepared through in situ free radical polymerization of N,N-dimethyl acrylamide and [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl) ammonium hydroxide with polyethylene glycol dimethacrylate as a crosslinker and carboxymethyl chitosan as filler. The gel mass fraction and swelling ratio were measured, and the preparation conditions were optimized. The result indicated that the hydrogel possessed a unique thermo-/pH-/ ion-sensitive behavior. The swelling ratio increased with the increase of temperature and ion concentration, and showed a decreasing trend with the increase in pH. In addition, the hydrogel was stable when the stimuli changed. Adsorption behavior of the hydrogel to Eosin Y (EY) was systematically investigated. The adsorption process can be described well by the pseudo-second-order kinetic model and Langmuir isotherm model, indicating that it was a chemical adsorption. The experiments indicated that the hydrogel exhibited good antifouling and reusability features. Therefore, the semi-IPN hydrogel with antifouling properties and thermo-/pH-/ion-sensitivity can be easily manufactured is expected to find applications in water treatment fields.

Characteristics of Adsorption/Desorption Process on Dolomite Adsorbent in the Copper(II) Removal from Aqueous Solutions

The removal of hazardous heavy metals that have been released into the environment due to industrial activities has become an important issue in recent years. The presented study concerned the removal of copper(II) ions from aqueous solutions using dolomites. Dolomite is a very attractive adsorbent due to its wide availability, low cost, good adsorption, and environmental compatibility. The paper describes the properties of D-I and D-II dolomites from two different open-cast mines in Poland. The properties of natural adsorbents were determined based on point of zero charges (PZC), elemental analysis of the adsorbent composition, FT-IR, XRD, and SEM spectra analysis. Depending on the initial concentration of the solution used, the adsorption efficiency of copper(II) ions was 58-80% for D-I and 80-97% for D-II. The adsorption mechanism in the case of D-II dolomite was mainly based on ion exchange, while chemisorption dominated the D-I dolomite surface. Considering the possibility of the regeneration and reuse of the adsorbent, dolomite D-II is a better material (the desorption efficiency of copper(II) ions was 58-80%). The adsorption behavior of dolomites has been described using six adsorption isotherms. The best fit was obtained for the Redlich-Peterson, Jovanović, and Langmuir isotherms, indicating that monolayer adsorption occurred. The maximum adsorption capacity for copper(II) was 378 mg/g of D-I and 308 mg/g of D-II.

Magnesium/aluminum layered double hydroxides intercalated with starch for effective adsorptive removal of anionic dyes

In this research, the adsorptive performance of a starch-magnesium/aluminum layered double hydroxide (S-Mg/Al LDH) composite was investigated for different organic dyes in single-component systems by conducting a series of batch mode experiments. S-Mg/Al LDH composite showed preferential adsorption of anionic dyes than cationic dyes. The marked impact of key process variables (e.g., contact time, adsorbent dosage, pH, and temperature) on its adsorption was investigated. Multiple isotherms, kinetics, and thermodynamic models were applied to describe adsorption behavior, diffusion, and uptake rates of the organic dyes over S-Mg/Al LDH composite. A better fitting of the non-linear Langmuir model reflects the predominance of monolayered adsorption of dye molecules on the composite surface. Partition coefficients (mg g^-1 μM^-1) for S-Mg/Al LDH were observed in the following descending order: Amaranth (665) > Tartrazine (186) > Sunset yellow (71) > Eosin yellow (65). Furthermore, comparative evaluation of the adsorption enthalpy, entropy, and Gibbs free energy values indicates that the adsorption process is spontaneous and exothermic. S-Mg/Al LDH composite maintained a stable adsorption/desorption recycling process over six consecutive cycles with the advantages of low cost, chemical/mechanical stability, and easy recovery. The results of this study are expected to expand the application of modified LDHs toward wastewater treatment.

Effective adsorption of bisphenol A from aqueous solution over a novel mesoporous carbonized material based on spent bleaching earth

In this study, the novel mesoporous carbonized material (HSBE/C) was prepared from clay/carbon composite (SBE/C) treated with hydrofluoric acid (HF) for the first time, and was employed to efficiently adsorb bisphenol A (BPA) in water. Specifically, SBE/C was derived from the pyrolysis of spent bleaching earth (SBE), an industrial waste. HF removed SiO₂ from SBE/C and increased the specific surface area of HSBE/C (from 100.21 to 183.56 m²/g), greatly providing more adsorption sites for enhanced BPA adsorption capacity. The Langmuir monolayer maximum adsorption capacity of HSBE/C (103.32 mg/g) was much higher than the commercial activated carbon (AC) (42.53 mg/g). The adsorption process by HSBE/C followed well with the Freundlich isotherm model and the pseudo-second-order kinetic model and also was endothermic (ΔH⁰ > 0) and spontaneous (ΔG⁰ < 0). Based on the systematic characterization and factor experiment (temperature, dosage, initial pH, co-existing ions), BPA adsorption mechanism by HSBE/C likely included the hydrogen bonding, electrostatic interaction, and hydrophobic interaction. Moreover, there was no secondary pollution during the total adsorption process. Extraordinary, HSBE/C manifested stability by NaOH desorption regeneration. This study provides a new sight for application of waste-based materials as the promising adsorbents in the treatment of endocrine disruptors.