Water‐based Synthesis and Properties of a Scandium 1,4‐Naphthalenedicarboxylate

Enhanced water stability and catalytic activity of Fe-based metal-organic frameworks with co-ligands for 2,4-dichlorophenol degradation

Fe-based metal-organic frameworks (MOFs) have good photocatalytic performance, environmental friendliness, low cost, and abundance. However, their applications are limited by low water stability, particularly in the presence of light irradiation and oxidizing agents. In this study, we present a MIL-53(Fe)-based MOF using 1,4-naphthalene dicarboxylic (1,4-NDC) and 1,4-benzenedicarboxylic (H2BDC) acid co-ligands, denoted MIL-53(Fe)-Nx, where Nx represents the ratio of 1,4-NDC. This MOF exhibits high water stability and good photocatalytic activity because of the hydrophobicity of naphthalene. The removal and mineralization rates for 100 mg/L 2,4-dichlorophenol reached 100% and 22%, respectively, within 60 min. After three cycles of use, the Fe leached into the solution from the catalysts was significantly lower than the maximum permissible limit indicated in the European Union standard. Of note, 1,4-NDC can be used to make a rigid MOF, thereby improving the crystallinity, porosity, and hydrophobicity of the resultant materials. It also significantly reduced the bandgap energy and improved the charge separation efficiency of the catalysts. This study provides a route to enhance the water stability of Fe-based MOFs via a mixed-ligand strategy to expand their applications in pollutant control.

Construction of a series of pH stable Ca-based MOFs, their CO2 adsorption and catalytic activity

In this study, three different solvent systems have been employed to investigate the effect of reaction parameters on the synthesis of four alkaline earth metal-based MOFs namely [Ca(0.5 1,4-phenyl diacetic acid)2(H2O)DMF]∞ (Ca-MOF-1), [Ca(1,4-naphthalene dicarboxylate)DMF]∞ (Ca-MOF-2), [Ca2(0.5 1,2,4,5-benzene tetracarboxylate)2(H2O)3DMF]∞ (Ca-MOF-3) and [Ca2(2,6-naphthalene dicarboxylate)2(H2O)6]∞ (Ca-MOF-4). The crystal structures of these four MOFs have been resolved through single crystal X-ray analysis and the bulk phase purity of these MOFs was assessed using PXRD and FT-IR analysis. To check the stability of these MOFs, thermogravimetric analysis (TGA) was carried out. To analyze the robustness of these MOFs, the PXRD of the samples was also collected at different pH levels. These MOFs were further explored as Lewis acid catalysts for the alcoholysis of epoxides and the activity of these catalysts depend on the open metal sites present in the MOFs. The catalytic activity follows the order: Ca-MOF-2 > Ca-MOF-4 > Ca-MOF-1 > Ca-MOF-3. The activity was also checked with various epoxide substrates using Ca-MOF-2. Density functional theory (DFT) calculations also support this trend with the help of the thermodynamic feasibility of epoxide binding, considering model MOF structures. The weak interaction between the epoxide oxygen and the metal centre of the most stable MOF structure has also been clarified by computational studies.

Synthesis, supramolecular isomerism, and photoluminescence of scandium(III) complexes with tetrafluoroterephthalate ligand

Here we present a new family of seven Sc(III) complexes with tetrafluoroterephthalate ligand (tFBDC2−), having non-polymeric and polymeric 2D and 3D structures. These complexes are characterized by SC XRD, PXRD,...

Three-Dimensional Electron Diffraction for Structural Analysis of Beam-Sensitive Metal-Organic Frameworks

Electrons interact strongly with matter, which makes it possible to obtain high-resolution electron diffraction data from nano- and submicron-sized crystals. Using electron beam as a radiation source in a transmission electron microscope (TEM), ab initio structure determination can be conducted from crystals that are 6–7 orders of magnitude smaller than using X-rays. The rapid development of three-dimensional electron diffraction (3DED) techniques has attracted increasing interests in the field of metal-organic frameworks (MOFs), where it is often difficult to obtain large and high-quality crystals for single-crystal X-ray diffraction. Nowadays, a 3DED dataset can be acquired in 15–250 s by applying continuous crystal rotation, and the required electron dose rate can be very low (<0.1 e s−1 Å−2). In this review, we describe the evolution of 3DED data collection techniques and how the recent development of continuous rotation electron diffraction techniques improves data quality. We further describe the structure elucidation of MOFs using 3DED techniques, showing examples of using both low- and high-resolution 3DED data. With an improved data quality, 3DED can achieve a high accuracy, and reveal more structural details of MOFs. Because the physical and chemical properties of MOFs are closely associated with their crystal structures, we believe 3DED will only increase its importance in developing MOF materials.