Chemical and Structural Modifications of Nanoporous Alumina and Its Optical Properties

Peculiar Porous Aluminum Oxide Films Produced via Electrochemical Anodizing in Malonic Acid Solution with Arsenazo-I Additive

The influence of arsenazo-I additive on electrochemical anodizing of pure aluminum foil in malonic acid was studied. Aluminum dissolution increased with increasing arsenazo-I concentration. The addition of arsenazo-I also led to an increase in the volume expansion factor up to 2.3 due to the incorporation of organic compounds and an increased number of hydroxyl groups in the porous aluminum oxide film. At a current density of 15 mA·cm⁻² and an arsenazo-I concentration 3.5 g·L⁻¹, the carbon content in the anodic alumina of 49 at. % was achieved. An increase in the current density and concentration of arsenazo-I caused the formation of an arsenic-containing compound with the formula Na_1,5Al₂(OH)_4,5(AsO₄)₃·7H₂O in the porous aluminum oxide film phase. These film modifications cause a higher number of defects and, thus, increase the ionic conductivity, leading to a reduced electric field in galvanostatic anodizing tests. A self-adjusting growth mechanism, which leads to a higher degree of self-ordering in the arsenazo-free electrolyte, is not operative under the same conditions when arsenazo-I is added. Instead, a dielectric breakdown mechanism was observed, which caused the disordered porous aluminum oxide film structure.

Optical Properties of Porous Alumina Assisted Niobia Nanostructured Films-Designing 2-D Photonic Crystals Based on Hexagonally Arranged Nanocolumns

Three types of niobia nanostructured films (so-called native, planarized, and column-like) were formed on glass substrates by porous alumina assisted anodizing in a 0.2 M aqueous solution of oxalic acid in a potentiostatic mode at a 53 V and then reanodizing in an electrolyte containing 0.5 M boric acid and 0.05 M sodium tetraborate in a potentiodynamic mode by raising the voltage to 230 V, and chemical post-processing. Anodic behaviors, morphology, and optical properties of the films have been investigated. The interference pattern of native film served as the basis for calculating the effective refractive index which varies within 1.75-1.54 in the wavelength range 190-1100 nm. Refractive index spectral characteristics made it possible to distinguish a number of absorbance bands of the native film. Based on the analysis of literature data, the identified oxide absorbance bands were assigned. The effective refractive index of native film was also calculated using the effective-medium models, and was in the range of 1.63-1.68. The reflectance spectra of all films show peaks in short- and long-wave regions. The presence of these peaks is due to the periodically varying refractive index in the layers of films in two dimensions. FDTD simulation was carried out and the morphology of a potential 2-D photonic crystal with 92% (wavelength 462 nm) reflectance, based on the third type of films, was proposed.

Integrating surface plasmon resonance and slow photon effects in nanoporous anodic alumina photonic crystals for photocatalysis

This study explores the potential of gold-coated titania-functionalized nanoporous anodic alumina distributed Bragg reflectors (Au-TiO₂-NAA-DBRs) as platforms to enhance photocatalytic reactions by integrating “slow photons” and surface plasmon resonance (SPR).

Engineering the Slow Photon Effect in Photoactive Nanoporous Anodic Alumina Gradient-Index Filters for Photocatalysis

In this study, we explore for the first time the capabilities of nanoporous anodic alumina gradient-index filters (NAA-GIFs) functionalized with titanium dioxide (TiO₂) photoactive layers to enhance photon-to-electron conversion rates and improve the efficiency of photocatalytic reactions by "slow photon" effect. A set of NAA-GIFs was fabricated by sinusoidal pulse anodization, in which a systematic modification of various anodization parameters (i.e., pore widening time, anodization period, and anodization time) enables the fine-tuning of the photonic stopband (PSB) of these nanoporous photonic crystals (PCs) across the spectral regions. The surface of NAA-GIFs was chemically modified with photoactive layers of TiO₂ to create a composite photoactive material with precisely engineered optical properties. The photocatalytic performance of TiO₂-functionalized NAA-GIFs was assessed by studying the photodegradation of three model organic dyes (i.e., methyl orange, Rhodamine B, and methylene blue) with well-defined absorption bands across different spectral regions under simulated irradiation conditions. Our study demonstrates that when the edges of characteristic PSB of TiO₂-modified NAA-GIFs are completely or partially aligned with the absorption band of the organic dyes, the photodegradation rate is enhanced due to "slow photon" effect. A rational design of the photocatalyst material with respect to the organic dye is demonstrated to be optimal to speed up photocatalytic reactions by an efficient management of photons from high-irradiance spectral regions. This provides new opportunities to develop high-performing photocatalytic materials for efficient photocatalysis with broad applicability.