Morphological implications of the interphase bridging crystalline and amorphousregions in semi-crystalline polymers

Defect-Induced Secondary Crystals Drive Two-Dimensional to Three-Dimensional Morphological Evolution in the Co-Self-Assembly of Polyferrocenylsilane Block Copolymer and Homopolymer

Bottom-up fabrication protocols for uniform 3D hierarchical structures in solution are rare. We report two different approaches to fabricate uniform 3D spherulites and their precursors using mixtures of poly(ferrocenyldimethylsilane) (PFS) block copolymer (BCP) and PFS homopolymer (HP). Both protocols are designed to promote defects in 2D assemblies that serve as intermediate structures. In a multistep seeded growth protocol, we add the BCP/HP mixture to (1D) rod-like PFS micelles in a selective solvent as first-generation seeds. This leads to 2D platelet structures. If this step is conducted at a high supersaturation, secondary crystals form on the basal surface of these platelets. Co-crystallization and rapid crystallization of BCP/HP promote the formation of defects that act as nucleation sites for secondary crystals, resulting in multilayer platelets. This is the key step. The multilayer platelets serve as second-generation seeds upon subsequent addition of BCP/HP blends and, with increasing supersaturation, lead to the sequential formation of uniform (3D) hedrites, sheaves, and spherulites. Similar structures can also be obtained by a simple one-pot direct self-assembly (heating-cooling-aging) protocol of PFS BCP/HP blends. In this case, for a carefully chosen but narrow temperature range, PFS HPs nucleate formation of uniform structures, and the annealing temperature regulates the supersaturation level. In both protocols, the competitive crystallization kinetics of HP/BCP affects the morphology. Both protocols exhibit broad generality. We believe the morphological transformation from 2D to 3D structures, regulated by defect formation, co-crystallization, and supersaturation levels, could apply to various semicrystalline polymers. Moreover, the 3D structures are sufficiently robust to serve as recoverable carriers for nanoparticle catalysts, exhibiting valuable catalytic activity and opening new possibilities for applications requiring exquisite 3D structures.

Polymer crystallization under external flow

The general aspects of polymer crystallization under external flow, i.e., flow-induced crystallization (FIC) from fundamental theoretical background to multi-scale characterization and modeling results are presented. FIC is crucial for modern polymer processing, such as blowing, casting, and injection modeling, as two-third of daily-used polymers is crystalline, and nearly all of them need to be processed before final applications. For academics, the FIC is intrinsically far from equilibrium, where the polymer crystallization behavior is different from that in quiescent conditions. The continuous investigation of crystallization contributes to a better understanding on the general non-equilibrium ordering in condensed physics. In the current review, the general theories related to polymer nucleation under flow (FIN) were summarized first as a preliminary knowledge. Various theories and models, i.e., coil-stretch transition and entropy reduction model, are briefly presented together with the modified versions. Subsequently, the multi-step ordering process of FIC is discussed in detail, including chain extension, conformational ordering, density fluctuation, and final perfection of the polymer crystalline. These achievements for a thorough understanding of the fundamental basis of FIC benefit from the development of various hyphenated rheometer, i.e., rheo-optical spectroscopy, rheo-IR, and rheo-x-ray scattering. The selected experimental results are introduced to present efforts on elucidating the multi-step and hierarchical structure transition during FIC. Then, the multi-scale modeling methods are summarized, including micro/meso scale simulation and macroscopic continuum modeling. At last, we briefly describe our personal opinions related to the future directions of this field, aiming to ultimately establish the unified theory of FIC and promote building of the more applicable models in the polymer processing.

Influence of process and formulation parameters on the formation of submicron particles by solvent displacement and emulsification-diffusion methods critical comparison

Solvent displacement and emulsification-diffusion are the methods used most often for preparing biodegradable submicron particles. The major difference between them is the procedure, which results from the total or partial water miscibility of the organic solvents used. This review is devoted to a critical and a comparative analysis based on the mechanistic aspects of particle formation and reported data on the influence of operating conditions, polymers, stabilizing agents and solvents on the size and zeta-potential of particles. In addition, a systematic study was carried out experimentally in order to obtain experimental data not previously reported and compare the data pertaining to the different methods. Thus the discussion of the behaviors reported in the light of the results obtained from the literature takes into account a wide range of theoretical and practical information. This leads to discussion on the formation mechanism of the particles and provides criteria for selecting the adequate method and raw materials for satisfying specific objectives in submicron particle design.