Blackening in yttria stabilized zirconia due to cathodic processes at solid platinum electrodes

Electrochemical decomposition of NOx and oxidation of HC and CO emissions by developing electrochemical cells for diesel engine emission control

Diesel engines are the most extensively used power source in automobiles and stationary power generation. The main drawback of using diesel engines is that it liberates a significant amount of NOx and PM emissions in the exhaust. NOx emission has a serious effect on the environment, and it has to be controlled effectively. SCR is the most widely used after-treatment technology to control NOx emission, but it has various disadvantages like ammonia slip and degradation of the catalyst. In this study, electrochemical decomposition of NOx is proposed for the simultaneous control of NOx, HC, and CO emissions in a diesel engine. In this work, ionically conducting ceramic electrochemical cells are investigated for control of diesel exhaust emissions. The electrochemical cell consisting of yttrium stabilized zirconia (YSZ) substrate plates as electrolyte and Ag-YSZ and NiO-YZS as an electrode material. The decomposition of NOx in an electrochemical cell is attained by passing electric current. A 2V supply of power was sufficient for effective operation of the electrochemical cell in all load conditions. All the experiments were conducted in a single-cylinder diesel engine. It is observed that the electrochemical cell shows high NOx decomposition rate of 80% at the exhaust temperatures between 350 and 400 °C. The HC reduction up to 65% and CO reduction up to 45% was observed with this technique. The power required to operate the electrochemical cell was low. The electrochemical NOx reduction is relatively simple technology with reduced complexity. From the experiment, it is observed that this concept works efficiently in the oxygen-rich diesel exhaust.

Investigation of Electrochemical, Optical and Thermal Effects during Flash Sintering of 8YSZ

This paper reports the electrochemical, optical and thermal effects occurring during flash sintering of 8 mol % yttria-stabilized zirconia (8YSZ). In-situ observations of polycrystalline and single crystal specimens revealed electrochemical blackening/darkening during an incubation period prior to flash sintering. The phenomenon is induced by cathodic partial reduction under DC fields. When using a low frequency AC field (0.1⁻10 Hz) the blackening is reversible, following the imposed polarity switching. Thermal imaging combined with sample colour changes and electrical conductivity mapping give a complete picture of the multi-physical phenomena occurring during each stage of the flash sintering event. The partial reduction at the cathode causes a modification of the electrical properties in the sample and the blackened regions, which are close to the cathode, are more conductive than the remainder of the sample. The asymmetrical nature of the electrochemical reactions follows the field polarity and causes an asymmetry in the temperature between the anode and cathode, with the positive electrode tending to overheat. It is also observed that the phenomena are influenced by the quality of the electrical contacts and by the atmosphere used.

Pulsed Polarization-Based NOx Sensors of YSZ Films Produced by the Aerosol Deposition Method and by Screen-Printing

The pulsed polarization technique on solid electrolytes is based on alternating potential pulses interrupted by self-discharge pauses. Since even small concentrations of nitrogen oxides (NO_x) in the ppm range significantly change the polarization and discharge behavior, pulsed polarization sensors are well suited to measure low amounts of NO_x. In contrast to all previous investigations, planar pulsed polarization sensors were built using an electrolyte thick film and platinum interdigital electrodes on alumina substrates. Two different sensor layouts were investigated, the first with buried Pt electrodes under the electrolyte and the second one with conventional overlying Pt electrodes. Electrolyte thick films were either formed by aerosol deposition or by screen-printing, therefore exhibiting a dense or porous microstructure, respectively. For screen-printed electrolytes, the influence of the electrolyte resistance on the NO_x sensing ability was investigated as well. Sensors with buried electrodes showed little to no response even at higher NO_x concentrations, in good agreement with the intended sensor mechanism. Electrolyte films with overlying electrodes, however, allowed the quantitative detection of NO_x. In particular, aerosol deposited electrolytes exhibited high sensitivities with a sensor output signal ΔU of 50 mV and 75 mV for 3 ppm of NO and NO₂, respectively. For screen-printed electrolytes, a clear trend indicated a decrease in sensitivity with increased electrolyte resistance.