Study of the complexation chemistry and speciation of thallium for on-line preconcentration with immobilised quinolin-8-ol

An On-Line Flow-Injection Sorbent Extraction System Coupled with Flame Atomic Absorption Spectrometry for Thallium Determination Using a PTFE Turning-Packed Column

A novel time-based flow-injection–solid-phase extraction system (FI–SPE) coupled with flame atomic absorption spectrometry (FAAS) for automatic on-line preconcentration and determination of thallium was developed. The efficiency of poly-tetrafluoroethylene (PTFE) turnings packed into a column as sorbent material was investigated for thallium extraction. Total thallium was determined by oxidizing thallium(I) to thallium(III), adding bromine in acidic solution. The formed [TlBr4]− anionic bromo complex was retained onto the PTFE turnings by on-line mixing with sodium diethyl dithiocarbamate (DDTC). The preconcentrated Tl(III)-DDTC complex was then effectively eluted with methyl isobutyl ketone (MIBK) and introduced into the flame atomizer for measurement and quantification. The column proved to be effective, stable, and reproducible, with a long lifetime. The enrichment factor was 105 for 60 s preconcentration time, and the sampling frequency 40 h−1. The detection limit was 1.93 μg L−1, and the relative standard deviation (RSD) was 3.2% at 50.0 μg L−1 concentration. The accuracy of the proposed method was estimated by analyzing certified reference materials and environmental and biological samples.

Speciation and determination of thallium by on-line microcolumn separation/preconcentration by flow injection-flame atomic absorption spectrometry using immobilized oxine as sorbent

A flow injection analysis (FIA) system incorporation a microcolumn of immobilized oxine on surfactant-coated alumina had been devised for performing rapid thallium enrichment/matrix removal in flame atomic absorption spectrometry (FAA). The preconcentration is based on the deposition of thallium(I) on microcolumn and subsequent elution with 500 microl of sodium thiosulfate (1 moll(-1)). In the presence of EDTA, only Tl(I) was retained on the microcolumn. Total thallium was determined after reduction of Tl(III) to Tl(I) by hydroxyl amine hydrochloride. A sample volume of 25 ml resulted in a preconcentration factor of 77. Precision at 30 microgl(-1) was 2.6% RSD (n=10). With 25 ml sampling volume a detection limit of 2.5 microgl(-1) was determined. The effect of potential interfering ions on the determination was studied. The method was applied for the determination of thallium in water, waste water, hair, nail, coal, and standard reference alloys. The accuracy was assessed through recovery experiment, independent analysis by Furnace-AAS, and analysis of certified reference alloys.

Separation and quantification of Tl(I) and Tl(III) in fresh water samples

The two oxidation states of thallium, Tl(I) and Tl(III), were quantified by IC-ICP-MS using complexation of Tl3+ with DTPA (penta-carboxymethyl-diethylenetriamine) and separation on a cation exchange column according to a modification of the method devised by Coetzee et al. In order to avoid successively lowered separation efficiency and loss of resolution during a run, a gradient elution was made using HCl instead of HNO3. With an ultrasonic nebuliser instead of a V-groove nebuliser the limit of detection for Tl(I) and Tl(III) could be lowered from 25 ng/L and 3.0 ng/L to 9.0 ng/L and 0.7 ng/L, respectively, which is adequate for many fresh water systems. The stability of Tl(III) in acidic solutions was found to be concentration dependent, with an initially high reduction rate of Tl(III). Exposure of the sample to light further increased the reduction rate. Addition of DTPA (0.01 mM) and acid (HNO3, 1%) to a sample with 1 mug/L Tl(III) stabilised the Tl(III) content for at least 48 h. Analysis of field samples showed that only acidification is inadequate to maintain the original distribution of Tl(I) and Tl(III). Internal calibration (standard addition) and correction of the analytical signal (205Tl) with a non-ionic internal standard (11B) yielded almost quantitative recoveries of both Tl(I) and Tl(III). A scheme for field sample preparation is proposed, including sampling, storage and pre-analysis treatment.