Removal of phenolic compounds by electroassisted advanced process for wastewater purification

Ecotoxicological Assessment of Thermally- and Hydrogen-Reduced Graphene Oxide/TiO₂ Photocatalytic Nanocomposites Using the Zebrafish Embryo Model

Advanced oxidation processes (AOPs) have recently attracted great interest in water pollution management. Using the zebrafish embryo model, we investigated the environmental impacts of two thermally (RGOTi)- and hydrogen (H₂RGOTi)-reduced graphene oxide/TiO₂ semiconductor photocatalysts recently employed in AOPs. For this purpose, acutoxicity, cardiotoxicity, neurobehavioral toxicity, hematopoietic toxicity, and hatching rate were determinate. For the RGOTi, the no observed effect concentration (NOEC, mortality/teratogenicity score <20%) and the median lethal concentration (LC50) were <400 and 748.6 mg/L, respectively. H₂RGOTi showed a NOEC similar to RGOTi. However, no significant mortality was detected at all concentrations used in the acutoxicity assay (up to1000 mg/L), thus indicating a hypothetical LC50 higher than 1000 mg/L. According to the Fish and Wildlife Service Acute Toxicity Rating Scale, RGOTi can be classified as "practically not toxic" and H₂RGOTi as "relatively harmless". However, both nanocomposites should be used with caution at concentration higher than the NOEC (400 mg/L), in particular RGOTi, which significantly (i) caused pericardial and yolk sac edema; (ii) decreased the hatching rate, locomotion, and hematopoietic activities; and (iii) affected the heart rate. Indeed, the aforementioned teratogenic phenotypes were less devastating in H₂RGOTi-treated embryos, suggesting that the hydrogen-reduced graphene oxide/TiO₂ photocatalysts may be more ecofriendly than the thermally-reduced ones.

An efficient eco advanced oxidation process for phenol mineralization using a 2D/3D nanocomposite photocatalyst and visible light irradiations

Nanocomposites (CNTi) with different mass ratios of carbon nitride (C₃N₄) and TiO₂ nanoparticles were prepared hydrothermally. Different characterization techniques were used including X-ray diffraction (XRD), UV-Vis diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS), transmission electron spectroscopy (TEM) and Brunauer-Emmett-Teller (BET). UV-Vis DRS demonstrated that the CNTi nanocomposites exhibited absorption in the visible light range. A sun light - simulated photoexcitation source was used to study the kinetics of phenol degradation and its intermediates in presence of the as-prepared nanocomposite photocatalysts. These results were compared with studies when TiO₂ nanoparticles were used in the presence and absence of H₂O₂ and/or O₃. The photodegradation of phenol was evaluated spectrophotometrically and using the total organic carbon (TOC) measurements. It was observed that the photocatalytic activity of the CNTi nanocomposites was significantly higher than that of TiO₂ nanoparticles. Additionally, spectrophotometry and TOC analyses confirmed that degraded phenol was completely mineralized to CO₂ and H₂O with the use of CNTi nanocomposites, which was not the case for TiO₂ where several intermediates were formed. Furthermore, when H₂O₂ and O₃ were simultaneously present, the 0.1% g-C₃N₄/TiO₂ nanocomposite showed the highest phenol degradation rate and the degradation percentage was greater than 91.4% within 30 min.

Removal of 4-Chlorophenol from Contaminated Water Using Activated Carbon from Dried Date Pits: Equilibrium, Kinetics, and Thermodynamics Analyses

Five different activated carbons (ACs) have been prepared from dried date pits using air and phosphoric acid as activating agents. The used phosphoric acid:date pit ratio dictated the characteristics of the prepared ACs; the equivalent BET-nitrogen surface area varied from 794 m²/g for a ratio of 5:1, to 1707 m²/g for a ratio of 2:1, whereas the micropore volume changed in value from 0.24 cm³/g for the 5:1 ratio to 0.59 cm³/g for the 2:1 ratio. The prepared ACs were tested to remove 4-chlorophenol (4-CP) from aqueous solutions by means of batch adsorption process. The prepared 2:1 AC exhibited the highest uptake with a maximum of 525 mg/g. Equilibrium pH studies showed that 4-CP removal was pH dependent; the maximum uptake occurred at an equilibrium pH value of 5.5. Dynamic studies showed that 4-CP uptake on 2:1 AC is rapid, with 80% of the maximum uptake achieved during the first 40 min. Both surface adsorption and intraparticle diffusion were identified to be effective adsorption mechanisms. Kinetic studies indicated a pseudo second-order reaction. Results of equilibrium adsorption experiments showed that the adsorption of the 4-CP on 2:1 AC is best described by the Langmuir model. The thermodynamics parameters of the adsorption (ΔG⁰, ΔH⁰, and ΔS⁰) were determined by studying the adsorption equilibrium at different temperatures. The values of these parameters indicated the spontaneous and endothermic nature of the adsorption phenomenon of 4-CP on the prepared ACs.

Effect of the graphene oxide reduction method on the photocatalytic and electrocatalytic activities of reduced graphene oxide/TiO2 composite

LSVs (50 mV s⁻¹) for hydrogen-reduced graphene oxide/TiO₂ composite in (i & ii) oxygen and (iii & iv) argon-saturated 0.5 M H₂SO₄ at 25 °C in the presence (ii & iv) and absence (i & iii) of 300 watt UV radiation.

Synthesis and evaluation of a molecularly imprinted polymer for 2,4-dinitrophenol

Molecular imprinted polymers (MIP) are considered one of the most promising selective and novel separation methods for removal phenolic compound in wastewater treatment. MIP are crosslinked polymeric materials that exhibit high binding capacity and selectivity towards a target molecule (template), purposely present during the synthesis process. In this work MIP were prepared in a bulk polymerization method in acetonitrile using 2,4-dinitrophenol, acrylamide, ethylene glycol dimethacrylate, and benzoyl peroxide as template, functional monomer, cross-linker and initiator, respectively. An adsorption process for removal of nitrophenol using the fabricated MIP was evaluated under various pH and time conditions. The parameters studied for 2,4-dinitrophenol includes adsorption kinetics, adsorption isotherm, and selectivity. The maximum adsorption of nitrophenol by the fabricated MIP was 3.50 mg/g. The adsorption of 2,4-dinitrophenol by the fabricated MIP was found effective at pH 6.0. A kinetics study showed that nitrophenol adsorption follows a second order adsorption rate and the adsorption isotherm data is explained well by the Langmuir model.

Dechlorination by combined electrochemical reduction and oxidation

Chlorophenols are typical priority pollutants listed by USEPA (U.S. Environmental Protection Agency). The removal of chlorophenol could be carried out by a combination of electrochemical reduction and oxidation method. Results showed that it was feasible to degrade contaminants containing chlorine atoms by electrochemical reduction to form phenol, which was further degraded on the anode by electrochemical oxidation. Chlorophenol removal rate was more than 90% by the combined electrochemical reduction and oxidation at current of 6 mA and pH 6. The hydrogen atom is a powerful reducing agent that reductively dechlorinates chlorophenols. The instantaneous current efficiency was calculated and the results indicated that cathodic reduction was the main contributor to the degradation of chlorophenol.