Fluoride and the caries lesion: interactions and mechanism of action

A Comparative In Vitro Physicochemical Analysis of Resin Infiltrants Doped With Bioactive Glasses

Objective This study aimed to investigate the longevity and effectiveness of bioactive glass (BAG)-based dental resin infiltrants. Materials and methods The three types of BAG - 45S5 bioglass (RIS), boron-substituted (RIB), and fluoride-substituted (RIF) - were incorporated with photoinitiated dimethacrylate monomers to create experimental resin infiltrants. ICON® (CN; DMG-America, Ridgefield Park, NJ) and pure resin (PR) were used as control groups in this study. Disc-shaped samples were prepared for the experimental and control groups. The samples were challenged with the pH cycle and immersed in the artificial saliva for 30 days. On Day 0 and Day 30, the pH cycle and artificial saliva immersion, Vicker's microhardness, surface roughness, and surface morphology were investigated. Results The RIF group's disc samples showed the highest Vicker's microhardness values (78.20 ±0.06) on Day 30 of artificial saliva immersion, whereas the CN group's values were the lowest (55.99 ±0.24). Following the pH cycling, the RIF displayed the highest hardness (64.15 ±1.89) whereas the CN group's values were the lowest (33.47 ±1.28). Regarding surface roughness, on Day 30, the RIB resin group exhibited the highest (1.14 ±0.001 µm). In contrast, the CN resin showed the lowest (1.07 ±0.06 µm) values, while immersed in the artificial saliva solution. In the same duration of time, in the pH cycling solution, PR showed the least (0.85 ±0.89 µm), while RIF showed the highest roughness value (0.94 ±0.54 µm). Morphological analysis revealed that following the artificial saliva immersion, the RIB, CN, and PR exhibited smoother surfaces compared to the RIS and RIF groups. However, when immersed in the pH cycling solution, RIB and RIF showed more resistance against acid attack. Conclusions Our results revealed that the experimental resin groups performed much better than the commercial resin infiltrants following artificial saliva and pH cycling challenges.

Characterization of chemical reactions of silver diammine fluoride and hydroxyapatite under remineralization conditions

Introduction

Silver Diammine Fluoride (SDF) is a clinically used topical agent to arrest dental caries. However, the kinetics of its chemical interactions with hydroxyapatite (HA), the principal inorganic component of dental enamel, are not known. The aim was to characterize the step-wise chemical interactions between SDF and HA powder during the clinically important process of remineralization.

Methods

Two grams of HA powder were immersed in 10 ml acetic acid pH = 4.0 for 2 h to mimic carious demineralization. The powder was then washed and dried for 24 h and mixed with 1.5 ml SDF (Riva Star) for 1 min. The treated powder was then air-dried for 3 min, and 0.2 g was removed and stored in individual tubes each containing 10 ml remineralizing solution. Powder was taken from each tube at various times of exposure to remineralization solution (0 min, 10 min, 2 h, 4 h, 8 h, 24 h, and 10 days), and characterized using Magic Angle Spinning-Nuclear Magnetic Resonance (MAS-NMR) spectroscopy.

Results and discussion

19F MAS-NMR spectra showed that calcium fluoride (CaF2) started to form almost immediately after HA was in contact with SDF. After 24 h, the peak shifted to -104.5 ppm suggesting that fluoride substituted hydroxyapatite (FSHA) was formed with time at the expense of CaF2. The 31P MAS-NMR spectra showed a single peak at 2.7 ppm at all time points showing that the only phosphate species present was crystalline apatite. The 35Cl MAS-NMR spectra showed formation of silver chloride (AgCl) at 24 h. It was observed that after the scan, the whitish HA powder changed to black color. In conclusion, this time sequence study showed that under remineralization conditions, SDF initially reacted with HA to form CaF2 which is then transformed to FSHA over time. In the presence of chloride, AgCl is formed which is subsequently photo-reduced to black metallic silver.

Chronic exposure to environmentally relevant concentration of fluoride impairs osteoblast's collagen synthesis and matrix mineralization: Involvement of epigenetic regulation in skeletal fluorosis

Globally, 200 million people are suffering from toxic manifestations of Fluoride(F), dental and skeletal fluorosis; unfortunately, there is no treatment. To unravel the pathogenesis of skeletal fluorosis, we established fluorosis mice by treating environmentally relevant concentration of F (15 ppm NaF) through drinking water for 4 months. As in skeletal fluorosis, locomotor disability, crippling deformities occur and thus, our hypothesis was F might adversely affects collagen which gives the bone tensile strength. This work inevitably had to be carried out on osteoblast cells, responsible for synthesis, deposition, and mineralization of bone matrix. Isolated osteoblast cells were confirmed by ALP activity and mineralized nodules formation. Expression of collagen Col1a1, Col1a2, COL1A1 was significantly reduced in treated mice. Further, a study revealed the involvement of epigenetic regulation by promoter hypermethylation of Col1a1; expressional alterations of transcription factors, calcium channels and other genes e.g., Cbfa-1, Tgf-β1, Bmp1, Sp1, Sp7, Nf-Kb p65, Bmp-2, Bglap, Gprc6a and Cav1.2 are associated with impairment of collagen synthesis, deposition and decreased mineralization thus, enfeebling bone health. This study indicates the possible association of epigenetic regulation in skeletal fluorosis. However, no association was found between polymorphisms in the Col1a1 (RsaI, HindIII) and Col1a2 (RsaI, HindIII) genes with fluorosis in mice.

Maintenance of enamel properties after bleaching with high-concentrated hydrogen-peroxide gel containing calcium polyphosphate sub-microparticles

OBJECTIVE

To assessed the physical and chemical properties of human-enamel after treatment with an experimental bleaching gel containing 35%-hydrogen peroxide (HP) and calcium polyphosphate sub-microparticles (CaPP).

MATERIALS AND METHODS

Enamel/dentin specimens (4 × 4 × 3 mm) were obtained (n = 120) and allocated to different groups: control (saliva only); experimental (HP35%); commercial (whiteness-HP-Maxx); CaPP0.5% (HP35% + CaPP0.5wt%); CaPP1.5% (HP35% + CaPP1.5wt%). Three sessions were performed. The specimens' color was assessed using a spectrophotometer and the color (ΔE/ΔE00) and bleaching index (ΔWID) determined. The surface roughness and microhardness were assessed with a roughness tester and Knoop indenter. Raman spectroscopy was performed to obtain the ratios between the areas under the 431, 580, and 1070 cm-1 and the 960 cm-1 bands (430:960, 580:960, 1070:960). Kruskal-Wallis and Dunn compared the color, Ra, and SMH data. The Raman data was analyzed with Kruskal-Wallis and Dunn (α = 5%).

RESULTS

The ΔE, ΔE00, and ΔWID were similar among the bleached groups (p > 0.05). The roughness was not different between the groups (p > 0.05). After the 3rd session, CaPP0.5% had higher microhardness than the experimental (p < 0.05). The 1070:960 was higher in the experimental than in the CaPP1.5% and control (p < 0.05).

CONCLUSIONS

In human enamel, CaPP did not alter the bleaching effectiveness or roughness, and additionally, CaPP-containing gels increased the microhardness and preserved the mineral content when compared to the experimental without CaPP.

CLINICAL RELEVANCE

Experimental bleaching gels containing calcium polyphosphate sub-microparticles as a mineral source reduce the mineral content alteration and superficial microhardness reduction, known potential side effects of the in-office bleaching treatments.

Relative dentin and enamel abrasivity of charcoal toothpastes

OBJECTIVES

Very little data are known about charcoal toothpastes. The aim of this study was to counteract the missing data by determining the relative dentin abrasivity (RDA) and relative enamel abrasivity (REA) values of charcoal toothpastes.

METHODS

Radioactively charged dentin and enamel samples were randomly divided into groups of eight specimens. Each group was brushed with two of total 12 charcoal toothpaste slurries and with a standard abrasive with a known RDA and REA value. The measured radioactivity in counts per minute within the slurries corresponds to the amount of dentin or enamel abraded. RDA and REA values of the charcoal toothpastes were expressed relative to the known value of the standard slurry.

RESULTS

The RDA and REA values of the charcoal toothpastes have a broad range of 24-166 and 0-14, respectively.

CONCLUSIONS

The RDA and REA values do not differ significantly from previously tested commercially available toothpastes. However, the lack of fluoride compounds in many of the investigated charcoal toothpastes can have a less beneficial effect for the consumers. It is very important to educate patients accordingly.

Combined remineralizing effect of arginine and fluoride on artificially demineralized human primary dentin evaluated using quantitative light induced fluorescence

Introduction

One the most common chronic dental diseases affecting children is dental caries. Dentin caries is a condition in which caries has progressed to the dentin and caused a significant depth of lesion. Clinical studies have revealed that an increased caries risk is associated with a decreased alkali-producing capacity of the microbial populations colonizing the oral cavity of adults, which arginine somewhat compensates for.

Aims

To evaluate the remineralizing efficacy of fluoridated toothpaste, with fluoride-arginine containing toothpaste on demineralized dentin of primary teeth using quantitative light-induced fluorescence™.

Materials and Methods

Forty-five primary molars were decoronated and sectioned to prepare dentin specimens and mounted in an acrylic block in a uniform manner using a customized acrylic jig. Samples were randomized into three groups, were subjected to demineralization to create artificial dentin caries lesion. Following this, all the 45 samples were subjected to multispecies bacterial pH cycling for 21 days. All the specimens were evaluated for postdemineralization, pH cycling day 7, 14, and 21 on QLF™.

Results

On day 21, maximum fluorescence gain was observed by the positive control group followed by the arginine and negative control group. The variation observed between positive control and arginine group was found to be statistically significant.

Conclusions

An in vitro development of artificial caries such as demineralized lesion on primary dentin sample using plaque biofilm was observed successfully under QLF after 72 h. Arginine in combination with fluoride showed almost similar remineralization of demineralized primary dentin compared to fluoride alone after 21 days of multispecies bacterial pH cycling.

Metal and Metal Oxide Nanoparticles in Caries Prevention: A Review

Nanoparticles based on metal and metallic oxide have become a novel trend for dental use as they interfere with bacterial metabolism and prevent biofilm formation. Metal and metal oxide nanoparticles demonstrate significant antimicrobial activity by metal ion release, oxidative stress induction and non-oxidative mechanisms. Silver, zinc, titanium, copper, and magnesium ions have been used to develop metal and metal oxide nanoparticles. In addition, fluoride has been used to functionalise the metal and metal oxide nanoparticles. The fluoride-functionalised nanoparticles show fluoride-releasing properties that enhance apatite formation, promote remineralisation, and inhibit demineralisation of enamel and dentine. The particles' nanoscopic size increases their surface-to-volume ratio and bioavailability. The increased surface area facilitates their mechanical bond with tooth tissue. Therefore, metal and metal oxide nanoparticles have been incorporated in dental materials to strengthen the mechanical properties of the materials and to prevent caries development. Another advantage of metal and metal oxide nanoparticles is their easily scalable production. The aim of this study is to provide an overview of the use of metal and metal oxide nanoparticles in caries prevention. The study reviews their effects on dental materials regarding antibacterial, remineralising, aesthetic, and mechanical properties.

Calcium and Vitamin D Supplementation Effectively Alleviates Dental and Skeletal Fluorosis and Retain Elemental Homeostasis in Mice

Fluoride (F) is an essential trace element, but chronic exposure beyond the permissible limit (1.5 ppm) effectuates dental and skeletal fluorosis. Although 200 million people across the world are suffering from toxic manifestations of F, till now proper treatment is not available. In this study, we assessed the effectiveness of calcium and vitamin D supplementation for alleviation of fluorosis. Swiss albino mice were divided into 6 groups; group I-control group (received drinking water ˂ 0.5 ppm F; within the permissible limit), group II-treated with 15 ppm of sodium fluoride (NaF) for 4 months, group III-treated with 15 ppm of NaF for 8 months through drinking water. Group IV-orally treated with 15 ppm NaF for 4 months, thereafter received only drinking water for next 4 months, group V-orally treated with 15 ppm NaF for 4 months, thereafter received drinking water supplemented with calcium and vitamin D (2.5-g calcium kg^-1 diet and 1000 IU vitamin D kg^-1 diet) for next 4 months, and group VI was treated with 15 ppm of NaF through drinking water as well as supplemented with calcium and vitamin D for 4 months. NaF treatment caused dental fluorosis, skeletal fluorosis, and alteration of bone's metal profile. Substitution of NaF-containing water with normal drinking water reduced the severity of fluorosis but supplementation of calcium and vitamin D effectively alleviated dental and skeletal fluorosis, reduced F deposition, and retained elemental homeostasis of the bone. Our findings strongly support that calcium and vitamin D act as redeemer of fluorosis. Graphical Abstract.

Dentine disorders and adhesive treatments: A systematic review

OBJECTIVES

A better understanding of the microstructure and mechanical properties of enamel and dentine may enable practitioners to apply the current adhesive dentistry protocols to clinical cases involving dentine disorders (dentinogenesis imperfecta or dentine dysplasia).

DATA/SOURCES

Publications (up to June 2020) investigating the microstructure of dentine disorders were browsed in a systematic search using the PubMed/Medline, Embase and Cochrane Library electronic databases. Two authors independently selected the studies, extracted the data in accordance with the PRISMA statement, and assessed the risk of bias with the Critical Appraisal Checklist. A Mann-Whitney U test was computed to compare tissues damage related to the two dentine disorders of interest.

STUDY SELECTION

From an initial total of 642 studies, only 37 (n = 164 teeth) were included in the present analysis, among which 18 investigating enamel (n = 70 teeth), 15 the dentine-enamel junction (n = 62 teeth), and 35 dentine (n = 156 teeth). Dentine is damaged in cases of dentinogenesis imperfecta and osteogenesis imperfecta (p = 2.55E-21 and p = 3.99E-21, respectively). These studies highlight a reduction in mineral density, hardness, modulus of elasticity and abnormal microstructure in dentine disorders. The majority of studies report an altered dentine-enamel junction in dentinogenesis imperfecta and in osteogenesis imperfecta (p = 6.26E-09 and p = 0.001, respectively). Interestingly, enamel is also affected in cases of dentinogenesis imperfecta (p = 0.0013), unlike to osteogenesis imperfecta (p = 0.056).

CONCLUSIONS

Taking into account all these observations, only a few clinical principles may be favoured in the case of adhesive cementation: (i) to preserve the residual enamel to enhance bonding, (ii) to sandblast the tooth surfaces to increase roughness, (iii) to choose a universal adhesive and reinforce enamel and dentine by means of infiltrant resins. As these recommendations are mostly based on in vitro studies, future in vivo studies should be conducted to confirm these hypotheses.

Exogenous Intake of Fluorides in Caries Prevention: Benefits and Risks

Caries incidence and prevalence have decreased significantly over the last few decades due to widespread use of fluoride. However, an increase in the prevalence of dental fluorosis has been reported in both fluoridated and non-fluoridated communities. Care must be taken to ensure that a balance between the optimal fluoride preventive effect at the individual and community level and minimal risk of dental fluorosis is maintained. This review describes the main sources of fluoride intake that have been identified: fluoridated drinking water, dietary fluoride supplement, and topical forms comprising toothpastes, rinses, gels and varnishes. The cited data were taken from meta-analytic studies and reports from Cochrane database systematic reviews up to December 2019. Efficiency, but safety, of topically applied fluorides in individual home care is dependent on the degree of compliance of individuals/parents and on the level of competence of providers of preventive counselling. The broad spectrum of these resources allows individualization of fluoride prevention based on risk analysis of caries attack and taking into consideration other preventive measures.

An in-vitro evaluation of fluoride content and enamel remineralization potential of two toothpastes containing different bioactive glasses

BACKGROUND

Many novel biomaterials have been incorporated in toothpastes to promote remineralization of tooth structure.

OBJECTIVES

This study was carried out to compare the discrepancies between declared and actual total fluoride (TF) or total soluble fluoride (TSF) concentration of two modern toothpastes containing bioactive glasses; these were also assessed for their remineralization potential.

MATERIALS AND METHODS

The TF and TSF concentration were assessed using a fluoride ion selective electrode. Enamel remineralization was evaluated through micro-hardness analysis. Eighteen enamel blocks were divided into three groups: 1 (n = 6; control), 2 (n = 6; Novamin® toothpaste), and 3 (n = 6; BiominF® toothpaste). The specimens were demineralized by 6 wt% citric acid (pH = 2.2). Subsequently, the specimens in group 1 were kept in artificial saliva (AS), while the specimens in groups 2 and 3 were stored in AS + Novamin® and AS + Biomin®, respectively.

RESULTS

Both Novamin® or BiominF® showed less TF concentration than their label claims. BiominF® had more TF and TSF compared to Novamin® (p < 0.05). The BiominF® toothpaste presented higher micro-hardness values on remineralization.

CONCLUSION

BiominF® toothpaste demonstrated more fluoride content and greater potential to promote remineralization of demineralized human enamel compared to Novamin®.

Influence of a novel pH-cycling model using dental microcosm biofilm on the remineralizing efficacy of fluoride in early carious lesions

OBJECTIVES

To evaluate the remineralizing efficacy of fluoride in early carious lesions using a novel microbial pH-cycling model that combines the chemical pH-cycling model with dental microcosm biofilms.

MATERIALS AND METHODS

Artificial carious lesions were formed in 48 bovine incisors. The chemical and microbial pH-cycling models were applied to 24 specimens, respectively; the latter was applied after formation of dental microcosm biofilms for 6 days, based on the human saliva inoculation. The pH-cycling schedule was repeated for 12 days. All specimens were evaluated for fluorescence loss (ΔF) using quantitative light-induced fluorescence-digital before and after the pH-cycling. Specimen biofilms were further analyzed for red/green values (R/G ratios) and colony-forming units (CFUs). One-way analysis of variance and Tukey's post hoc analysis were used to analyze change in fluorescence loss (ΔΔF) according to the pH-cycling model and treatment.

RESULTS

When the chemical pH-cycling and microbial pH-cycling models were used, ΔΔF was 1.36 (p = 0.008) and 1.17 (p > 0.05) times higher, respectively, in the fluoride-treated group than that in the distilled water-treated group. In the microbial pH-cycling model, R/G ratios and CFU counts of biofilms were not significantly different between treatments (p > 0.05).

CONCLUSIONS

No significant difference was observed in the remineralizing efficacy of fluoride according to the presence of dental biofilms covering early carious lesions.

CLINICAL RELEVANCE

The remineralizing efficacy of fluoride could be overestimated in the absence of dental biofilms. Therefore, for accurate evaluation of the clinical value of remineralizing agents, dental biofilms should be included in in vitro tests.

EDX-analysis of fluoride precipitation on human enamel

One mechanism of action for the anticaries effect of topical fluoridation is through precipitation of CaF₂. In this in vitro study energy-dispersive x-ray spectroscopy (EDX) is used as a semiquantitative method to detect enamel fluoride-precipitation under the influence of acidic and neutral pH-value and absence or presence of a salivary pellicle. Crowns of 30 human caries-free third molars were quartered into four specimens and the enamel surface ground flat and polished. Two specimens each were stored in human saliva (120 minutes pellicle formation). Teeth were randomly allocated into 6 treatment groups: NaF_a (experimental acidic sodium fluoride; 12500 ppmF⁻, pH 4.75); NaF_n (experimental neutral sodium fluoride; 12500 ppmF⁻, pH 7.0); GB_a (acidic gel base; 0 ppmF⁻, pH 4.75); GB_n (neutral gel base; 0 ppmF⁻, pH 7.0); AmF-NaF_a (experimental acidic amine/sodium fluoride; 12500 ppmF⁻, pH 4.75); EG_a (acidic amine/sodium fluoride; Elmex Geleé, CP-GABA GmbH; 12500 ppmF⁻, pH 4.75). Each gel was applied for 60 seconds to one specimen with and one specimen without pellicle. Two specimens served as controls (no gel, without/with pellicle). Atomic percent (At%) of O, F, Na, Mg, P, Ca was measured by EDX. ∆At% and Ca/P-ratios were calculated. EDX could semi-quantify superficial enamel fluoride-precipitation. Only specimens treated with acidic fluoride gels showed fluoride-precipitation, a salivary pellicle tended to decrease At%F.

Effectiveness of casein phosphopeptide-amorphous calcium phosphate-containing products in the prevention and treatment of white spot lesions in orthodontic patients: A systematic review

The purpose of the present systematic review was to evaluate the effectiveness of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP)-containing products in the prevention and treatment of active white spot lesions (WSL) in orthodontic patients. Searched the Scopus, PubMed, Web of Science, Cochrane, Virtual Health Language, ClinicalTrials, and Open Gray databases without limitations on the year or language of publication. We included controlled clinical trials with patients with fixed orthodontic appliances under the use of CPP-ACP-containing products compared to control, placebo, or other interventions in the prevention and treatment of WSL around orthodontic braces. Case reports, editorials, in vitro studies, annals of congress, and reviews were excluded. To assess the risk of bias, the revised version of the Cochrane tool for randomized trials (RoB 2.0) and Risk Of Bias In Non-randomized Studies for non-randomized trials were used. The biases were graded low, moderate, and high according to the tools used. Of the 599 articles found, 11 met the inclusion criteria. Of these, nine were randomized, controlled clinical trials and two were non-randomized. Two studies were considered to have moderate bias risk, and the most-used CPP-ACP presented form was a cream for topical applications. Although CPP-ACP-containing products did not differ from other fluoride products, they were able to reduce WSL and neutralize the pH around the orthodontic braces. Products containing CPP-ACP are effective in preventing and treating WSL around the braces. However, further studies with the same measurement method and periods of use, and other forms of presentation of CPP-ACP are needed.

Análise da atividade antimicrobiana de probióticos e sua adesividade a bráquetes ortodônticos: estudo in vitro

Resumo Introdução A presença de aparelho ortodôntico fixo dificulta a higienização e potencializa o acúmulo de biofilme bacteriano nas superfícies dentárias. O desenvolvimento de produtos que minimize isso é desejo de pesquisadores em todo o mundo. Objetivo Verificar a ação bacterapêutica de produtos lácteos contendo ou não probióticos sob pool de Streptococcus mutans (SM) (ATCC 25175) e S salivarius (SS) (ATCC 7073), além da adesão desses produtos à superfície de bráquetes ortodônticos. Material e método Pool de cepas ATCC de SM e SS foi formado e plaqueado sobre placa de Petri contendo meio de cultura brain heart infusion ágar (BHI). Após formação do meio, um orifício foi feito no centro da placa seguido do seu preenchimento com 150 µL dos produtos a serem testados, formando os seguintes grupos: GL - Leite bovino; GLP - Leite bovino com probiótico; GLF - Leite fermentado; e GLFP - Leite fermentado com probiótico. Na sequência, as placas foram incubadas por 48h, em estufa a 37ºC. A seguir, foi feita a medição do halo formado entre o produto e o meio com régua milimetrada. Já no disco de membrana, foi formado biofilme com o mesmo pool de cepas, sob discos de membrana. Em seguida, foi feita a diluição seriada contendo o produto de acordo com o grupo: P1 (água); P2 (L); P3 (LP); P4 (LFP), seguida do plaqueamento e a contagem total de micro-organismos. Para a adesividade dos produtos lácteos, bráquetes ortodônticos foram submergidos em cada solução (GL, GLP, GLF e GLFP) e foram incubadas a 37°C/24h. Posteriormente, cada bráquete foi transferido para um ependorf contendo solução salina estéril, que foi submetida a diluições seriadas, posteriormente incubadas a 37°C/48h sob microaerofilia para contagem das UFC/mL. Para análise dos dados, utilizaram-se os testes Levene, Shapiro-Wilk e Kruskal-Wallis. O nível de significância adotado foi de 5% (α = 0,05). Resultado Não houve formação de halo de inibição entre os produtos e o meio de cultura (p<0,05); no disco de membrana, não foram observadas diferenças estatísticas entre os grupos (p=0,679); os grupos tratados com leite bovino com probiótico e leite fermentado com probiótico apresentaram adesividade aos bráquetes ortodônticos (p=0,056). Conclusão Os achados do presente estudo permitem concluir que, em estudos in vitro, não foi possível verificar a bacterioterapia a partir de produtos lácteos contendo ou não probióticos em cepas de SM e SS.

An In Vitro Study on the Effect of Amorphous Calcium Phosphate and Fluoride Solutions on Color Improvement of White Spot Lesions

The ability of remineralizing agents to improve the color of white spot lesions (WSL) is an important aspect that should be investigated. The aim of this study was to evaluate the effects of 0.05% amorphous calcium phosphate (ACP), 0.5% ACP, and 0.05% fluoride solutions, as well as artificial saliva on the color improvement of white spot lesions (WSLs). In this in vitro study, 50 human premolar teeth were randomly classified into five groups. At baseline, all the samples were assessed by using a colorimeter (E0). Then, white spot lesions were induced on the surface of the teeth by means of a pH-cycling model, and the colorimeter was used again (E1). Afterwards, samples of the 1st and 2nd groups were kept in 0.05% ACP and 0.5% ACP solutions for 1 min/day, respectively. The 3rd group specimens were placed in 0.05% fluoride solution for 1 min/day. The other two groups were kept in artificial saliva and distilled in water separately. All the samples were assessed by the colorimeter for a third time (E2). We found no significant difference between the groups in ∆E1. There was also no significant difference among 0.05% ACP solution, 0.5% ACP solution, 0.05% fluoride solution, and artificial saliva considering ∆E2. However, a significant difference was noted between the above-mentioned solutions and distilled water in ∆E2. With respect to ∆E3, there were considerable differences between ACP solution and artificial saliva. The same results were obtained for the difference between fluoride solution and artificial saliva. However, no significant difference was found among 0.05% ACP, 0.5% ACP, and 0.05% fluoride solutions in terms of ∆E3. In Conclusion, ACP is as effective as fluoride in the color improvement of WSLs and the recommended treatment for this purpose is daily use of 0.05% ACP, 0.5% ACP or 0.05% fluoride solutions.

Assessment of the effectiveness of mouthwashes in reducing cariogenic biofilm in orthodontic patients: a systematic review

OBJECTIVES

The use of fixed orthodontic appliances makes it difficult to clean the teeth and accessories associated with it. For this reason, orthodontic patients have used oral antiseptics as coadjuvent means to reduce cariogenic plaque. The aim of this systematic review was to evaluate the effectiveness of oral antiseptics on the reduction of cariogenic plaque on orthodontic patients.

DATA

This review has been registered at PROSPERO--international prospective register of systematic reviews under the number CRD42013006857.

SOURCES

A systematic review of the literature was conducted in the following electronic databases: Scopus, PubMed, Web of Science, Medline, Embase and Cochrane, Grey literature and Clinical Trials, without limitations on the year of publication or language. Clinical studies in patients with fixed orthodontic appliances, who were making use of oral mouthwashes in order to reduce cariogenic plaque, were included. Articles with patients using systemic drugs, syndromic patients, those using mouthwashes for other purposes and/or using different cleaning techniques, and clinical cases were excluded. After selection by title and abstract, potentially eligible articles were read in full. The methodological quality and risk of biases of articles included were evaluated according to the characteristics of the study, measurements and statistical analyses of the study. The methodological quality was classified as high, moderate or low.

STUDY SELECTION

The search identified 2716 articles, of which 15 met the inclusion criteria. Of these, 8 analyzed chlorhexidine-based mouthwashes, while in 1 article Cetylpyridinium was used; 1 analyzed the mouthwash containing sanguinaria; 1 the use of NaF; 2 articles the use of AmF/SnF2; 2 the use of Listerine(®), 1 also analyzed the association between mouthwashes with octenidine and with PVP-I. Of the articles analyzed, 11 were classified as having high and 4 as having moderate methodological quality.

CONCLUSION

There is evidence of effectiveness of the use of oral mouthwashes in the control of cariogenic plaque in patients with fixed orthodontic appliances. The orthodontists may suggest the use of oral antiseptics in the oral hygiene of their patients as coadjuvent means to reduce cariogenic plaque.

CLINICAL SIGNIFICANCE

Given current evidence, orthodontists may prescribe mouthwash as an auxiliary method in the control of cariogenic biofilm in orthodontic patients.

In vitro anti-caries effect of fluoridated hydroxyapatite-coated preformed metal crowns

Aim

To synthesise fluoridated hydroxyapatite (FA) crystals directly on preformed metal crowns (PMCs) and evaluate the anti-cariogenic properties in an in vitro model.

Methods

FA crystals were grown on etched PMCs and stainless steel discs and characterised by SEM. FA-coated discs allowed fluoride release to be assessed from a known surface area of FA crystals. Discs were divided into four groups (n = 6/group) and exposed to solutions at pH 4–7. Fluoride levels in solution were measured after each exposure. Twelve FA-coated and 12 non-coated PMCs were cemented onto human molars using glass ionomer (GI) or unfilled resin, making four groups of six teeth; FA-coated + GI, FA-coated + resin; non-coated + GI and non-coated + resin. Teeth were exposed to acidified gelatin (pH = 4.3) for 9 weeks.

Results

SEM showed FA crystal growth on interior and exterior of the crowns. Average fluoride release from FA-coated discs was 0.16 mg/L/cm² at pH < 5.0. Teeth were sectioned through the lesion. Polarised microscopic examination revealed significantly smaller lesions in FA-coated crown groups compared to non-coated crown groups.

Conclusion

FA-coated PMCs demonstrated carious lesion preventing effects, i.e. fluoride release and reduction of demineralisation at crown/tooth interface. FA-coated crowns could be an aesthetic, inexpensive and caries preventive alternative in clinical dentistry.

Remineralization agents - new and effective or just marketing hype?

This is a review of the need for better remineralization and of the status of calcium-based remineralizing agents for use in anti-caries toothpastes. Use of fluoride toothpastes has markedly reduced caries. However, the decline may be over or in reverse. There is a limit to what fluoride alone can do; complementary agents are needed. Using plaque as a reservoir for calcium-based agents holds promise. Plaque fluid is already supersaturated with respect to relevant calcium phosphates at neutral pH; extra calcium may lead to surface-blocking and sub-optimal lesion consolidation. However, at cariogenic pH, lesions may be more porous to the ingress of mineral, leading to fuller consolidation, and controlled release of calcium should reduce undersaturation with respect to enamel and accelerate deposition of fluorhydroxyapatite. Clinical data to validate in vitro screening models are scarce. Direct progression to in situ models may often be appropriate. The spectrum of lesion types, from softening to relatively advanced subsurface, and lesion activity should be considered. Far from being 'marketing hype', progress with calcium-based remineralizing agents is both encouraging and scientifically sound. Clinical evidence exists for the efficacy of some agents, but further unequivocal clinical data are needed before these agents might be considered 'effective' when delivered from toothpaste.

In situ demineralisation of human enamel studied by synchrotron-based X-ray microtomography--a descriptive pilot-study

An in situ study was designed to investigate naturally developed demineralisation in human enamel in a widely non-destructive manner in combination with X-ray microtomography. Samples of human enamel were carried in the oral cavity of participants for 24 h daily for either 21 or 29 days using so-called intraoral mandibular appliances (ICTs). Demineralisation was thereby generated in a natural way without causing caries in the subjects' dentition. By employing synchrotron-based X-ray microtomography (XMT) in combination with volume image analysis, a quantification and three-dimensional visualisation of different stages of mineral density loss was possible. Basic features of the demineralised samples were similar to those reported in earlier in vitro studies. However, the analysed samples showed significant differences in the morphology of surface attack and the degree of mineral density loss depending on the carrier, the exposure time and the position within the ICT. In particular, the varying local conditions within a carrier's oral cavity seem to be different than in an in vitro study. Our results show that the combination of ICTs and quantitative image analysis applied to XMT data provides an analytical tool which is highly suited for the fundamental investigation of naturally developed demineralisation processes.

Effect of Caries Infiltration Technique and Fluoride Therapy on Microhardness of Enamel Carious Lesions

Enamel white spot subsurface lesions compromise esthetics and precede cavitation; therefore, they must be halted. The aim of this study was to evaluate the effect of a caries infiltration technique and fluoride therapy on the microhardness of enamel carious lesions. Subsurface carious lesions were produced in 60 bovine specimens with polished enamel surfaces. The specimens were divided into four groups (n=15), according to the treatment used: CON, control—immersion in artificial saliva; DF, daily 0.05% fluoride solution; WF, weekly 2% fluoride gel; and IC, resin infiltration (Icon). The specimens were kept in artificial saliva and evaluated for microhardness at five points: baseline, after caries production, after four and eight weeks of treatment, and a final evaluation after being submitted to a new acid challenge. The repeated-measures analysis of variance showed significant differences according to the type of treatment (TREAT; p=0.001) and time of evaluation (EV; p=0.001). The results of the Tukey test were TREAT: CON = 45.18 (±29.17)a, DF = 107.75 (±67.38)b, WF = 83.25 (±51.17)c, and IC = 160.83 (±91.11)d. Analysis of correlation between the TREAT and EV factors showed no significant differences for DF (138.63 ± 38.94) and IC (160.99 ± 46.13) after the new acid challenge. The microhardness results in decreasing order after eight weeks were IC &gt; DF &gt; WF &gt; CON. It was concluded that the microhardness of carious lesions increased with the infiltration of resin, while the final microhardness after a new acid challenge was similar for DF and IC.

Demineralization of enamel in primary second molars related to properties of the enamel

Enamel structure is of importance in demineralization. Differences in porosity in enamel effect the rate of demineralization, seen between permanent and deciduous teeth. Individual differences have been shown in the mean mineral concentration values in enamel, the role of this in demineralization is not thoroughly investigated. The aim of this study was to study variations of depths of artificial lesions of demineralization and to analyze the depth in relation to variations in the chemical and mineral composition of the enamel. A demineralized lesion was created in second primary molars from 18 individuals. Depths of lesions were then related to individual chemical content of the enamel. Enamel responded to demineralization with different lesion depths and this was correlated to the chemical composition. The carbon content in sound enamel was shown to be higher where lesions developed deeper. The lesion was deeper when the degree of porosity of the enamel was higher.

In vitro study of the effects of fluoride-releasing dental materials on remineralization in an enamel erosion model

OBJECTIVES

This study was conducted to compare the remineralization effects of five regimens on the loss of fluorescence intensity, surface microhardness, roughness and microstructure of bovine enamel after remineralization. We hope that these results can provide some basis for the clinical application of these materials.

METHODS

One hundred bovine incisors were prepared and divided into the following five groups, which were treated with distinct dental materials: (1) Clinpro™ XT varnish (CV), (2) F-varnish (FV), (3) Tooth Mousse (TM), (4) Fuji III LC(®) light-cured glass ionomer pit and fissure sealant (FJ) and (5) Base Cement(®) glass polyalkenoate cement (BC). Subsequently, they were detected using four different methods: quantitative light-induced fluorescence, microhardness, surface 3D topography and scanning electron microscopy (SEM).

RESULTS

The loss of fluorescence intensity of CV, BC and FJ groups showed significant decreases after remineralization (p<0.05). The microhardness values of the BC group were significantly higher than those of the other groups (p<0.05) after 6 weeks of remineralization. The CV group's surface roughness was significantly lower than those of the other groups after 6 weeks of remineralization (p<0.05). Regarding microstructure values, the FV group showed many round particles deposited in the bovine enamel after remineralization. However, the other four groups mainly showed needle-like crystals.

CONCLUSIONS

Glass ionomer cement (GIC)-based dental materials can promote more remineralization of the artificial enamel lesions than can NaF-based dental materials. Resin-modified GIC materials (e.g., CV and FJ) have the potential for more controlled and sustained release of remineralized agents. The effect of TM requires further study.

Detection accuracy of proximal caries by phosphor plate and cone-beam computerized tomography images scanned with different resolutions

This study was carried out to assess whether the spatial resolution has an impact on the detection accuracy of proximal caries in flat panel CBCT (cone beam computerized tomography) images and if the detection accuracy can be improved by flat panel CBCT images scanned with high spatial resolution when compared to digital intraoral images. The CBCT test images of 45 non-restored human permanent teeth were respectively scanned with the ProMax 3D and the DCT Pro scanners at different resolutions. Digital images were obtained with a phosphor plate imaging system Digora Optime. Eight observers evaluated all the test images for carious lesion within the 90 proximal surfaces. With the histological examination serving as the reference standard, observer performances were evaluated by receiver operating characteristic (ROC) curves. The areas under the ROC curves were analyzed with two-way analysis of variance. No significant differences were found among the CBCT images and between CBCT and digital images when only proximal enamel caries was detected (p = 0.989). With respect to the detection of proximal dentinal caries, significant difference was found between CBCT and digital images (p < 0.001) but not among CBCT images. The spatial resolution did not have an impact on the detection accuracy of proximal caries in flat panel CBCT images. The flat panel CBCT images scanned with high spatial resolution did not improve the detection accuracy of proximal enamel caries compared to digital intraoral images. CBCT images scanned with high spatial resolutions could not be used for proximal caries detection.