3D osteotomies-improved accuracy with patient-specific instruments (PSI)

State of the art review: The pathogenesis and management of Madelung deformity

Madelung deformity remains a fascinating yet unresolved challenge. There is an increasing awareness for early diagnosis by healthcare providers with improvement in diagnostic modalities, however, the exact mechanisms for the development of the deformity have still to be clarified. While some corrective procedures have been described to effectively address an established deformity, the existing literature lacks clear and evidence-based treatment guidelines on how to proceed in daily practice. This review article aims to summarize the current best evidence on this topic, including particular areas of controversy and areas with need for future research.

Personalised opening wedge high tibial osteotomy with patient-specific plates and instrumentation accurately controls coronal correction and posterior slope: Results from a prospective first case series

BACKGROUND

Patient specific devices represent a promising tool to improve accuracy and simplify high tibial osteotomy (HTO) procedures. The current study aims to assess accuracy of the correction of alignment and posterior tibial slope (PTS), and provide patient reported outcomes (PROMs) of a new personalised cutting guide and fixation plate (TOKA) system for HTO in patients with medial osteoarthritis (OA) and varus knee.

METHODS

25 patients (mean age 54.4 years) with medial OA and varus knee malalignment who underwent HTO with the TOKA system were prospectively evaluated pre-operatively, 1, 3, 6 and 12-months follow-up. Standing long-leg and lateral radiographs of the knee were used to assess the hip-knee-ankle (HKA) angle and the PTS, respectively. Accuracy was defined as the difference in planned minus achieved correction. The patient reported outcomes collected were the KOOS score, EQ5D, KSS score, and VAS pain scores. All statistical analyses were performed using IBM SPSS Statistics for Windows.

RESULTS

The mean preoperative HKA was 170.7° (SD ± 3.2°); the mean postoperative HKA was 177.4° (SD ± 2.9°). The overall mean difference between planned and achieved correction in terms of HKA was 2.1° (SD ± 2.0°). The mean difference between planned and achieved PTS was 0.2° (SD ± 0.4°). All the assessed PROMs had a significant (p < 0.001) increase from the pre-operative value to postoperative evaluation and showed a significant (p < 0.001) improvement with follow-up time.

CONCLUSIONS

TOKA personalised HTO system showed accurate correction in terms of both coronal and sagittal alignment, and excellent patient reported outcomes.

LEVEL OF EVIDENCE

4, prospective case series. Registration in public trial registry: registered at ClinicalTrial.gov [NCT04574570].

[Osteotomies around the knee: preoperative planning using CT-based three-dimensional analysis, patient-specific cutting and reduction guides]

OBJECTIVE

The goal of osteotomy is either to restore pretraumatic anatomic conditions or to shift the load to less affected compartments.

INDICATIONS

Indications for computer-assisted 3D analysis and the use of patient-specific osteotomy and reduction guides include "simple" deformities and, in particular, multidimensional complex (especially posttraumatic) deformities.

CONTRAINDICATIONS

General contraindications for performing a computed tomography (CT) scan or for an open approach for performing the surgery.

SURGICAL TECHNIQUE

Based on CT examinations of the affected and, if necessary, the contralateral healthy extremity as a healthy template (including hip, knee, and ankle joints), 3D computer models are generated, which are used for 3D analysis of the deformity as well as for calculation of the correction parameters. For the exact and simplified intraoperative implementation of the preoperative plan, individualized guides for the osteotomy and the reduction are produced by 3D printing.

POSTOPERATIVE MANAGEMENT

Partial weight-bearing from the first postoperative day. Increasing load after the first x‑ray control 6 weeks postoperatively. No limitation of the range of motion.

RESULTS

There are several studies that have analyzed the accuracy of the implementation of the planned correction for corrective osteotomies around the knee joint with the use of patient-specific instruments with promising results.

[Three-dimensional analysis of posttraumatic tibial shaft malunion and correction based on the healthy, contralateral leg]

OBJECTIVE

Three-dimensional (3D) analysis and implementation with patient-specific cutting and repositioning blocks enables correction of complex tibial malunions. Correction can be planned using the contralateral side or a statistical model. Patient-specific 3D-printed cutting guide blocks enable a precise osteotomy and reduction guide blocks help to achieve anatomical reduction. Depending on the type and extent of correction, fibula osteotomy may need to be considered to achieve the desired reduction.

CONTRAINDICATIONS

a) Poor soft tissue (flap surgery, adherent skin in field of operation); b) infection; c) peripheral artery disease (stage III and IV classified according to Fontaine, critical transcutaneous oxygen partial pressure, TcPO2); d) general contraindication to surgery.

SURGICAL TECHNIQUE

Before surgery, a 3D model of both lower legs is created based on computed tomography (CT) scans. Analysis of the deformity based on the contralateral side in a 3D computer model (CASPA) and planning of the osteotomy. If the contralateral side also has a deformity, a statistical model can be used. Printing of patient-specific guides made of nylon (PA2200) for the osteotomy and reduction. Surgery is performed in supine position, antibiotic prophylaxis, thigh tourniquet, which is used as needed. Ventrolateral approach to the tibia. Attachment of the patient-specific osteotomy guide, performance of the osteotomy. Reduction using the guide. Fibula osteotomy through a lateral approach is performed if the reduction of the tibia is hindered by the fibula. This can be performed freehand or with patient-specific guides. Wound closure.

POSTOPERATIVE MANAGEMENT

Compartment monitoring. Passive mobilization of the ankle in the cast as soon as the wound healing has progressed. Partial weightbearing in a lower leg cast for at least 6-12 weeks, depending on the routinely performed radiographic assessment 6 weeks postoperatively. Thromboprophylaxis with low molecular weight heparin until cast removal.

RESULTS

Patient-specific correction of malunions are generally good. This could be confirmed for distal tibial corrections. For tibial shaft deformities, the final results are still pending. Preliminary results, however, show good feasibility with a pseudarthrosis rate of 10% without postoperative infection.

Custom-Made Devices Represent a Promising Tool to Increase Correction Accuracy of High Tibial Osteotomy: A Systematic Review of the Literature and Presentation of Pilot Cases with a New 3D-Printed System

Background: The accuracy of the coronal alignment corrections using conventional high tibial osteotomy (HTO) falls short, and multiplanar deformities of the tibia require consideration of both the coronal and sagittal planes. Patient-specific instrumentations have been introduced to improve the control of the correction. Clear evidence about customized devices for HTO and their correction accuracy lacks. Methods: The databases PUBMED and EMBASE were systematically screened for human and cadaveric studies about the use of customized devices for high tibial osteotomy and their outcomes concerning correction accuracy. Furthermore, a 3D-printed customized system for valgus HTO with three pilot cases at one-year follow-up was presented. Results: 28 studies were included. The most commonly used custom-made devices for HTO were found to be cutting guides. Reported differences between the achieved and targeted correction of hip-knee-ankle angle and the posterior tibial slope were 3° or under. The three pilot cases that underwent personalized HTO with a new 3D-printed device presented satisfactory alignment and clinical outcomes at one-year follow-up. Conclusion: The available patient-specific devices described in the literature, including the one used in the preliminary cases of the current study, showed promising results in increasing the accuracy of correction in HTO procedure.