High-load preconditioning of human soft tissue hamstring grafts: An in vitro biomechanical analysis

Losartan in Combination With Bone Marrow Stimulation Showed Synergistic Effects on Load to Failure and Tendon Matrix Organization in a Rabbit Model

PURPOSE

To investigate the effects of combining bone marrow stimulation (BMS) with oral losartan to block transforming growth factor β1 (TGF-β1) on biomechanical repair strength in a rabbit chronic injury model.

METHODS

Forty rabbits were randomly allocated into 4 groups (10 in each group). The supraspinatus tendon was detached and left alone for 6 weeks to establish a rabbit chronic injury model and was then repaired in a surgical procedure using a transosseous, linked, crossing repair construct. The animals were divided into the following groups: control group (group C), surgical repair only; BMS group (group B), surgical repair with BMS of the tuberosity; losartan group (group L), surgical repair plus oral losartan (TGF-β1 blocker) for 8 weeks; and BMS-plus-losartan group (group BL), surgical repair plus BMS plus oral losartan for 8 weeks. At 8 weeks after repair, biomechanical and histologic evaluations were performed.

RESULTS

The biomechanical testing results showed significantly higher ultimate load to failure in group BL than in group B (P = .029) but not compared with group C or group L. A 2 × 2 analysis-of-variance model found that the effect of losartan on ultimate load significantly depended on whether BMS was performed (interaction term F1,28 = 5.78, P = .018). No difference was found between the other groups. No difference in stiffness was found between any groups. On histologic assessment, groups B, L, and BL showed improved tendon morphology and an organized type I collagen matrix with less type III collagen compared with group C. Group BL showed the most highly organized tendon matrix with more type I collagen and less type III collagen, which indicates less fibrosis. Similar results were found at the bone-tendon interface.

CONCLUSIONS

Rotator cuff repair combined with oral losartan and BMS of the greater tuberosity showed improved pullout strength and a highly organized tendon matrix in this rabbit chronic injury model.

CLINICAL RELEVANCE

Tendon healing or scarring is accompanied by the formation of fibrosis, which has been shown to result in compromised biomechanical properties, and is therefore a potential limiting factor in healing after rotator cuff repair. TGF-β1 expression has been shown to play an important role in the formation of fibrosis. Recent studies focusing on muscle healing and cartilage repair have found that the downregulation of TGF-β1 by losartan intake can reduce fibrosis and improve tissue regeneration in animal models.

The tibial tunnel drilling angles of 60° provided a lower ultimate load to failure on a single bundle posterior cruciate ligament graft using interference screw fixation compared to 30°/45°

PURPOSE

To biomechanically compare the initial fixation strength of grafts among three tibial tunnel angles (30°/45°/60°) in transtibial posterior cruciate ligament (PCL) reconstruction.

METHODS

A series of transtibial PCL reconstruction models were established with porcine tibias and bovine tendons. Specimens were randomly assigned to three groups according to the angles between the tibial tunnel and the perpendicular line of the tibial shaft: Group A (30°, n = 12), Group B (45°, n = 12), and Group C (60°, n = 12). The area of the tunnel entrance, the segmental bone mineral density (sBMD) of the graft fixation site of the tibia and the maximum insertion torque of the interference screw were measured. Finally, load to failure tests were carried out on the graft-screw-tibia constructs at the same rate.

RESULTS

Ultimate load to failure in Group C (335.2 ± 107.5 N) was significantly lower than that in Group A (584.1 ± 127.9 N, P < 0.01) and Group B (521.9 ± 95.9 N, P < 0.01). There were no significant differences between biomechanical properties of Groups A and B (n.s.). The posterior part fractures of the tibial tunnel exit occurred in eight specimens of Group C. In addition, the ultimate load was proven to be related to insertion torque (rho = 0.7, P < 0.01), sBMD (rho = 0.7, P < 0.01), and the area of the tunnel entrance (rho =- 0.4, P = 0.01).

CONCLUSION

The ultimate load to failure was significantly lower in tibial PCL interference screw fixation for tunnels drilled at 60° compared to 30°/45°. In addition, the ultimate load was significantly correlated with insertion torque, sBMD and the area of the tunnel entrance. Given that the load to failure of distal fixation may not be sufficient for early postoperative rehabilitation, a 60° tunnel should not be recommended to drill in tibia during PCL reconstruction.

Modified Lemaire Tenodesis Forces in Cadaveric Specimens Are Not Affected by Random Small-Scale Variations in the Femoral Insertion Point During Active Knee Joint Flexion-Extension

Purpose

To directly measure lateral extra-articular tenodesis (LET) forces supporting anterior cruciate ligament reconstruction (ACLR) during dynamic flexion-extension cycles induced by simulated active muscle forces, to investigate the influence of random surgical variation in the femoral LET insertion point around the target insertion position, and to determine potential changes to the extension behavior of the knee joint in a cadaveric model.

Methods

After iatrogenic anterior cruciate ligament deficiency and simulated anterolateral rotatory instability, 7 fresh-frozen cadaveric knee joints were treated with isolated ACLR followed by combined ACLR-LET. The specimens were tested on a knee joint test bench during active dynamic flexion-extension with simulated muscle forces. LET forces and the degree of knee joint extension were measured. Random variation in the LET insertion point around the target insertion position was postoperatively quantified by computed tomography.

Results

In extension, the median LET force increased to 39 ± 2 N (95% confidence interval [CI], 36 to 40 N). In flexion over 70°, the LET was offloaded (2 ± 1 N; 95% CI, 0 to 2 N). In this study, small-scale surgical variation in the femoral LET insertion point around the target position had a negligible effect on the graft forces measured. We detected no difference in the degree of knee joint extension after combined ACLR-LET (median, 1.0° ± 3.0°; 95% CI, -6.2° to 5.2°) in comparison with isolated ACLR (median, 1.1° ± 3.3°; 95% CI, -6.7° to 6.1°; P = .62).

Conclusions

LET forces in combined ACLR-LET increased to a limited extent during active knee joint flexion-extension independent of small-scale variation around 1 specific target insertion point. Combined ACLR-LET did not change knee joint extension in comparison with isolated ACLR under the testing conditions used in this biomechanical study.

Clinical Relevance

Low LET forces can be expected during flexion-extension of the knee joint. Small-scale deviations in the femoral LET insertion point around the target insertion position in the modified Lemaire technique might have a minor effect on graft forces during active flexion-extension.

Modified Lemaire tenodesis reduces anterior cruciate ligament graft forces during internal tibial torque loading

PURPOSE

The aim of the study was to directly measure graft forces of an anterior cruciate ligament reconstruction (ACLR) and a lateral extra-articular tenodesis (LET) using the modified Lemaire technique in combined anterior cruciate ligament (ACL) deficient and anterolateral rotatory instable knees and to analyse the changes in knee joint motion resulting from combined ACLR + LET.

METHODS

On a knee joint test bench, six fresh-frozen cadaveric specimens were tested at 0°, 30°, 60°, and 90° of knee flexion in the following states: 1) intact; 2) with resected ACL; 3) with resected ACL combined with anterolateral rotatory instability; 4) with an isolated ACLR; and 5) with combined ACLR + LET. The specimens were examined under various external loads: 1) unloaded; 2) with an anterior tibial translation force (ATF) of 98 N; 3) with an internal tibial torque (IT) of 5 Nm; and 4) with a combined internal tibial torque of 5 Nm and an anterior tibial translation force of 98 N (IT + ATF). The graft forces of the ACLR and LET were recorded by load cells incorporated into custom devices, which were screwed into the femoral tunnels. Motion of the knee joint was analysed using a 3D camera system.

RESULTS

During IT and IT + ATF, the addition of a LET reduced the ACLR graft forces up to 61% between 0° and 60° of flexion (P = 0.028). During IT + ATF, the LET graft forces reached 112 N. ACLR alone did not restore native internal tibial rotation after combined ACL deficiency and anterolateral rotatory instability. Combined ACLR + LET was able to restore native internal tibial rotation values for 0°, 60° and 90° of knee flexion with decreased internal tibial rotation at 30° of flexion.

CONCLUSION

The study demonstrates that the addition of a LET decreases the forces seen by the ACLR graft and reduces residual rotational laxity after isolated ACLR during internal tibial torque loading. Due to load sharing, a LET could support the ACLR graft and perhaps be the reason for reduced repeat rupture rates seen in clinical studies. Care must be taken not to limit the internal tibial rotation when performing a LET.

Full thickness quadriceps tendon grafts with bone had similar material properties to bone-patellar tendon-bone and a four-strand semitendinosus grafts: a biomechanical study

PURPOSE

Despite increasing interest in utilizing quadriceps tendon (QT) grafts in anterior cruciate ligament reconstruction (ACLR), data on the optimal quadriceps graft thickness are limited. The purpose of this study was to characterize the mechanical properties for the quadriceps tendon, comparing full-thickness (FT) QT grafts with and without bone to a partial-thickness (PT) QT graft, and comparing the three QT grafts to four-stranded semitendinosus (4-SST) and bone-patellar tendon-bone (BTB) grafts and one experimental graft, the two-stranded rectus femoris (RF).

METHODS

Forty-eight (n = 48) young cadaveric grafts (mean age 32 ± 6 years) were utilized for testing with N = 8 specimens in each of the following groups; (1) FT QT with bone, (2) FT QT without bone, (3) PT QT without bone, (4) BTB, (5) RF, and (6) 4-SST. Each specimen was harvested and rigidly fixed in custom clamps to a dynamic tensile testing machine for biomechanical evaluation. Graft ultimate load and stiffness were recorded. Independent groups one-factor ANOVAs and Tukey's pairwise comparisons were performed for statistical analyses.

RESULTS

FT QT with bone and 4-SST grafts demonstrated similar ultimate loads to BTB grafts (both n.s), whereas PT QT demonstrate statistically significantly lower ultimate loads to BTB grafts (n.s) and 4-SST grafts (n.s). Furthermore, no statistically significant differences were observed between the ultimate loads of FT QT vs. PT QT grafts without bone (n.s) or between FT QT with vs. without bone (n.s). FT QT grafts with bone did not demonstrate statistically significantly greater ultimate loads than PT QT grafts without bone (n.s). The RF graft demonstrated statistically significantly lower ultimate loads to BTB grafts (p < 0.005) and 4-SST grafts (p < 0.014).

CONCLUSIONS

Full thickness QT grafts with bone had similar material properties to BTB and a 4-SST grafts, while Partial thickness QT graft without bone had significantly lower material properties than BTB and 4-SST, in a biomechanical setting.

How preconditioning and pretensioning of grafts used in ACLigaments surgical reconstruction are influenced by their mechanical time-dependent characteristics: Can we optimize their initial loading state?

PURPOSE

Consensus about a pre-implant preparation protocol adaptable to any graft used in Anterior Cruciate Ligament reconstruction is still lacking. In fact, there is not agreement on reliable metrics that consider both specific graft dimensional characteristics, such as its diameter, and the inherent properties of its constitutive material, i.e. ligaments or tendons. Aim of the present study was to investigate and propose the applied engineering stress as a possible metrics.

METHODS

Preconditioning and pretensioning protocol involved groups of grafts with different section (10 or 32 mm²) and materials (i.e. human patellar and hamstring tendons, and synthetic grafts). A 140 N load was applied to the grafts and maintained for 100 s. Initial stress and following stress-relaxation (a mechanical characteristic that can be related to knee laxity) were specifically analysed.

FINDINGS

Initial stress, ranging between 4 and 12 MPa, was affected primarily by the graft cross-section area and secondarily by the choice of the graft material. In terms of loss of the initial stress, stress-relaxation behaviour varied instead on a narrower range, namely 13-17%.

INTERPRETATION

Engineering stress can be identified as the correct metrics to optimize the initial state of each graft to avoid excessive stiffness, laxity or fatigue rupture phenomena.

Anterior Cruciate Ligament Graft Conditioning Required to Prevent an Abnormal Lachman and Pivot Shift After ACL Reconstruction: A Robotic Study of 3 ACL Graft Constructs

BACKGROUND

Anterior cruciate ligament (ACL) graft conditioning protocols to decrease postoperative increases in anterior tibial translation and pivot-shift instability have not been established.

PURPOSE

To determine what ACL graft conditioning protocols should be performed at surgery to decrease postoperative graft elongation after ACL reconstruction.

STUDY DESIGN

Controlled laboratory study.

METHODS

A 6 degrees of freedom robotic simulator evaluated 3 ACL graft constructs in 7 cadaver knees for a total of 19 graft specimens. Knees were tested before and after ACL sectioning and after ACL graft conditioning protocols before reconstruction. The ACL grafts consisted of a 6-strand semitendinosus-gracilis TightRope, bone-patellar tendon-bone TightRope, and bone-patellar tendon-bone with interference screws. Two graft conditioning protocols were used: (1) graft board tensioning (20 minutes, 80 N) and (2) cyclic conditioning (5°-120° of flexion, 90-N anterior tibial load) after graft reconstruction to determine the number of cycles needed to obtain a steady state with no graft elongation. After conditioning, the grafts were cycled a second time under anterior-posterior loading (100 N, 25° of flexion) and under pivot-shift loading (100 N anterior, 5-N·m internal rotation, 7 N·m valgus) to verify that the ACL flexion-extension conditioning protocol was effective.

RESULTS

Graft board tensioning did not produce a steady-state graft. Major increases in anterior tibial translation occurred in the flexion-extension graft-loading protocol at 25° of flexion (mean ± SD: semitendinosus-gracilis TightRope, 3.4 ± 1.1 mm; bone-patellar tendon-bone TightRope, 3.2 ± 1.0 mm; bone-patellar tendon-bone with interference screws, 2.4 ± 1.5 mm). The second method of graft conditioning (40 cycles, 5°-120° of flexion, 90-N anterior load) produced a stable conditioned state for all grafts, as the anterior translations of the anterior-posterior and pivot-shift cycles were statistically equivalent ( P < .05, 1-20 cycles).

CONCLUSION

ACL graft board conditioning protocols are not effective, leading to deleterious ACL graft elongations after reconstruction. A secondary ACL graft conditioning protocol of 40 flexion-extension cycles under 90-N graft loading was required for a well-conditioned graft, preventing further elongation and restoring normal anterior-posterior and pivot-shift translations.

CLINICAL RELEVANCE

There is a combined need for graft board tensioning and robust cyclic ACL graft loading before final graft fixation to restore knee stability.