Biological applications of scanning electrochemical microscopy: chemical imaging of single living cells and beyond

Visualizing Electrochemical CO2 Conversion via the Emerging Scanning Electrochemical Microscope: Fundamentals, Applications and Perspectives

With the rapid development and maturity of electrochemical CO2 conversion involving cathodic CO2 reduction reaction (CO2RR) and anodic oxygen evolution reaction (OER), conventional ex situ characterizations gradually fall behind in detecting real-time products distribution, tracking intermediates, and monitoring structural evolution, etc. Nevertheless, advanced in situ techniques, with intriguing merits like good reproducibility, facile operability, high sensitivity, and short response time, can realize in situ detection and recording of dynamic data, and observe materials structural evolution in real time. As an emerging visual technique, scanning electrochemical microscope (SECM) presents local electrochemical signals on various materials surface through capturing micro-current caused by reactants oxidation and reduction. Importantly, SECM holds particular potentials in visualizing reactive intermediates at active sites and obtaining instantaneous morphology evolution images to reveal the intrinsic reactivity of active sites. Therefore, this review focuses on SECM fundamentals and its specific applications toward CO2RR and OER, mainly including electrochemical behavior observation on local regions of various materials, target products and onset potentials identification in real-time, reaction pathways clarification, reaction kinetics exploration under steady-state conditions, electroactive materials screening and multi-techniques coupling for a joint utilization. This review undoubtedly provides a leading guidance to extend various SECM applications to other energy-related fields.

A review of innovative electrochemical strategies for bioactive molecule detection and cell imaging: Current advances and challenges

Cellular heterogeneity poses a major challenge for tumor theranostics, requiring high-resolution intercellular bioanalysis strategies. Over the past decades, the advantages of electrochemical analysis, such as high sensitivity, good spatio-temporal resolution, and ease of use, have made it the preferred method to uncover cellular differences. To inspire more creative research, herein, we highlight seminal works in electrochemical techniques for biomolecule analysis and bioimaging. Specifically, micro/nano-electrode-based electrochemical techniques enable real-time quantitative analysis of electroactive substances relevant to life processes in the micro-nanostructure of cells and tissues. Nanopore-based technique plays a vital role in biosensing by utilizing nanoscale pores to achieve high-precision detection and analysis of biomolecules with exceptional sensitivity and single-molecule resolution. Electrochemiluminescence (ECL) technology is utilized for real-time monitoring of the behavior and features of individual cancer cells, enabling observation of their dynamic processes due to its capability of providing high-resolution and highly sensitive bioimaging of cells. Particularly, scanning electrochemical microscopy (SECM) and scanning ion conductance microscopy (SICM) which are widely used in real-time observation of cell surface biological processes and three-dimensional imaging of micro-nano structures, such as metabolic activity, ion channel activity, and cell morphology are introduced in this review. Furthermore, the expansion of the scope of cellular electrochemistry research by innovative functionalized electrodes and electrochemical imaging models and strategies to address future challenges and potential applications is also discussed in this review.

Temperature Effect on the Electrochemical Current Response during Scanning Electrochemical Microscopy of Living Cells

Scanning electrochemical microscopy (SECM) is being used increasingly to monitor electrochemical processes at the interface of living cells and electrodes. This allows the detection and quantification of biomarkers that further the understanding of various diseases. Rapid SECM experiments are often carried out without monitoring the analyte solution temperature or are performed at room temperature. The reported research demonstrates that temperature control is crucial during SECM imaging of living cells to obtain reliable data. In this study, a SECM-integrated thermostatic ring on the sample stage enabled imaging of living biological cells in a constant height mode at various temperatures. Two-dimensional line scans were conducted while scanning single Adenocarcinoma Cervical cancer (HeLa) cells. Numerical modeling was carried out to evaluate the effect of the temperature on the electrochemical current response of living cells to compare the apparent heterogeneous rate constant (k0), representing cellular reaction kinetics. This study reveals that even slight temperature variations of approximately 2 °C affect the reaction kinetics of single living cells, altering the measured current during SECM.

Investigating Localized Electrochemical of Ferrocenyl-Imidazolium in Ionic Liquid Using Scanning Electrochemical Microscopy Configuration

In the present work, the localized electrochemical behavior of redox molecule in ionic liquid has been investigated using scanning electrochemical microscopy. The electrochemical response of ferrocenyl-imidazolium redox mediator was studied by recording approach curves over a conducting and insulating substrate in an undiluted ionic liquid. The SECM approach curve over the conducting substrate displays a positive feedback, as observed in classical solvent. However, in the case of the insulating substrate, the approach curve reveals different shapes, depending on the used approach speed. In this configuration, low approach speed is necessary to reach the expected negative feedback. Interestingly, at a very close distance between the UME and the insulating substrate, a thin film behavior is revealed. In addition, the approach curves on both insulator and conducting substrates can be reconstructed from punctual responses at different distance tip-substrate. The latter match perfectly with the expected theoretical curves over conducting and insulating under diffusion control.

Simultaneous Intelligent Imaging of Nanoscale Reactivity and Topography by Scanning Electrochemical Microscopy

Scanning electrochemical microscopy (SECM) enables reactivity and topography imaging of single nanostructures in the electrolyte solution. The in situ reactivity and topography, however, are convoluted in the real-time image, thus requiring another imaging method for subsequent deconvolution. Herein, we develop an intelligent mode of nanoscale SECM to simultaneously obtain separate reactivity and topography images of non-flat substrates with reactive and inert regions. Specifically, an ∼0.5 μm-diameter Pt tip approaches a substrate with an ∼0.15 μm-height active Au band adjacent to an ∼0.4 μm-wide slope of the inactive glass surface followed by a flat inactive glass region. The amperometric tip current versus tip-substrate distance is measured to observe feedback effects including redox-mediated electron tunneling from the substrate. The intelligent SECM software automatically terminates the tip approach depending on the local reactivity and topography of the substrate under the tip. The resultant short tip-substrate distances allow for non-contact and high-resolution imaging in contrast to other imaging modes based on approach curves. The numerical post-analysis of each approach curve locates the substrate under the tip for quantitative topography imaging and determines the tip current at a constant distance for topography-independent reactivity imaging. The nanoscale grooves are revealed by intelligent topography SECM imaging as compared to scanning electron microscopy and atomic force microscopy without reactivity information and as unnoticed by constant-height SECM imaging owing to the convolution of topography with reactivity. Additionally, intelligent reactivity imaging traces abrupt changes in the constant-distance tip current across the Au/glass boundary, which prevents constant-current SECM imaging.

Nanoelectrochemistry in the study of single-cell signaling

Label-free biosensing has been the dream of scientists and biotechnologists as reported by Vollmer and Arnold (Nat Methods 5:591-596, 2008). The ability of examining living cells is crucial to cell biology as noted by Fang (Int J Electrochem 2011:460850, 2011). Chemical measurement with electrodes is label-free and has demonstrated capability of studying living cells. In recent years, nanoelectrodes of different functionality have been developed. These nanometer-sized electrodes, coupled with scanning electrochemical microscopy (SECM), have further enabled nanometer spatial resolution study in aqueous environments. Developments in the field of nanoelectrochemistry have allowed measurement of signaling species at single cells, contributing to better understanding of cell biology. Leading studies using nanoelectrochemistry of a variety of cellular signaling molecules, including redox-active neurotransmitter (e.g., dopamine), non-redox-active neurotransmitter (e.g., acetylcholine), reactive oxygen species (ROS), and reactive nitrogen species (RNS), are reviewed here.

Nanoscale Intelligent Imaging Based on Real-Time Analysis of Approach Curve by Scanning Electrochemical Microscopy

Scanning electrochemical microscopy (SECM) enables high-resolution imaging by examining the amperometric response of an ultramicroelectrode tip near a substrate. Spatial resolution, however, is compromised for nonflat substrates, where distances from a tip far exceed the tip size to avoid artifacts caused by the tip-substrate contact. Herein, we propose a new imaging mode of SECM based on real-time analysis of the approach curve to actively control nanoscale tip-substrate distances without contact. The power of this software-based method is demonstrated by imaging an insulating substrate with step edges using standard instrumentation without combination of another method for distance measurement, e.g., atomic force microscopy. An ∼500 nm diameter Pt tip approaches down to ∼50 nm from upper and lower terraces of a 500 nm height step edge, which are located by real-time theoretical fitting of an experimental approach curve to ensure the lack of electrochemical reactivity. The tip approach to the step edge can be terminated at <20 nm prior to the tip-substrate contact as soon as the theory deviates from the tip current, which is analyzed numerically afterward to locate the inert edge. The advantageous local adjustment of tip height and tip current at the final point of tip approach distinguishes the proposed imaging mode from other modes based on standard instrumentation. In addition, the glass sheath of the Pt tip is thinned to ∼150 nm to rarely contact the step edge, which is unavoidable and instantaneously detected as an abrupt change in the slope of approach curve to prevent damage of the fragile nanotip.

Analysing single live cells by scanning electrochemical microscopy

Scanning electrochemical microscopy (SECM) offers single live cell activities along its topography toward cellular physiology and pathology.

Quantifying microbial chatter: scanning electrochemical microscopy as a tool to study interactions in biofilms

Bacteria are often found in their natural habitats as spatially organized biofilm communities. While it is clear from recent work that the ability to organize into precise spatial structures is important for fitness of microbial communities, a significant gap exists in our understanding regarding the mechanisms bacteria use to adopt such physical distributions. Bacteria are highly social organisms that interact, and it is these interactions that have been proposed to be critical for establishing spatially structured communities. A primary means by which bacteria interact is via small, diffusible molecules including dedicated signals and metabolic by-products; however, quantitatively monitoring the production of these molecules in time and space with the micron-scale resolution required has been challenging. In this perspective, scanning electrochemical microscopy (SECM) is discussed as a powerful tool to study microbe-microbe interactions through the detection of small redox-active molecules. We highlight SECM as a means to quantify and spatially resolve the chemical mediators of bacterial interactions and begin to elucidate the mechanisms used by bacteria to regulate the emergent properties of biofilms.

Preparative enrichment of human tissue cells capable to change a site of growth in vitro or in vivo - Recent developments

Human cells are heterogeneous in regard to their biochemical features and functions. Detailed knowledge about each single cell type is important to understand the whole organism. In order to get a deeper insight in the concert of life, it has to be considered that cell populations such as thyroid cells, epithelial breast cells, endothelial cells, or chondrocytes are heterogeneous in regard to function, RNA expression patterns and protein content. This is true for normal cells and even more relevant for cancer cells. A number of sophisticated methods were developed to enrich cohorts of cells generally belonging to a defined type but outstanding by distinct characteristics, which can be detected by microscopic, proteomic or genomic methods. There is a great interest to investigate human cells, which are able to change their site of growth within the human body leaving an original site, migrating through vessels and reentering another site. In this review experiments are summarized showing that the application of microgravity-exposure of human cells and cell electrophoresis enable a characterization of cells, which leave a site of growth to enter another one. Biochemical features of separated subpopulations are described and their usefulness for deeper investigation is highlighted.

Scanning electrochemical microscopy: an analytical perspective

Scanning electrochemical microscopy (SECM) has evolved from an electrochemical specialist tool to a broadly used electroanalytical surface technique, which has experienced exciting developments for nanoscale electrochemical studies in recent years. Several companies now offer commercial instruments, and SECM has been used in a broad range of applications. SECM research is frequently interdisciplinary, bridging areas ranging from electrochemistry, nanotechnology, and materials science to biomedical research. Although SECM is considered a modern electroanalytical technique, it appears that less attention is paid to so-called analytical figures of merit, which are essential also in electroanalytical chemistry. Besides instrumental developments, this review focuses on aspects such as reliability, repeatability, and reproducibility of SECM data. The review is intended to spark discussion within the community on this topic, but also to raise awareness of the challenges faced during the evaluation of quantitative SECM data.

Single Cell Oxygen Mapping (SCOM) by Scanning Electrochemical Microscopy Uncovers Heterogeneous Intracellular Oxygen Consumption

We developed a highly sensitive oxygen consumption scanning microscopy system using platinized platinum disc microelectrodes. The system is capable of reliably detecting single-cell respiration, responding to classical regulators of mitochondrial oxygen consumption activity as expected. Comparisons with commercial multi-cell oxygen detection systems show that the system has comparable errors (if not smaller), with the advantage of being able to monitor inter and intra-cell heterogeneity in oxygen consumption characteristics. Our results uncover heterogeneous oxygen consumption characteristics between cells and within the same cell´s microenvironments. Single Cell Oxygen Mapping (SCOM) is thus capable of reliably studying mitochondrial oxygen consumption characteristics and heterogeneity at a single-cell level.

Sensing cisplatin-induced permeation of single live human bladder cancer cells by scanning electrochemical microscopy

Cisplatin is a widely used anti-cancer agent, which was believed to trigger apoptosis of cancer cells by forming DNA adducts. However, recent studies evidenced a cisplatin-induced extrinsic apoptotic pathway through interaction with plasma membranes. We present quantitative time-course imaging of cisplatin-induced permeation of ferrocenemethanol to single live human bladder cancer cells (T24) using scanning electrochemical microscopy (SECM). Simultaneous quantification of cellular topography and membrane permeability was realized by running SECM in the depth scan mode. It was demonstrated that the acute addition of cisplatin to the outer environment of T24 cells immediately induced membrane permeability change in 5 min, which indicated a loosened structure of the cellular membrane upon cisplatin dosage. The cisplatin-induced permeation of T24 cells might be a one-step action, an extrinsic mechanism, since the cell response was quick, and no continuous increase in the membrane permeability was observed. The time-lapse SECM depth scan method provided a simple and facile way of monitoring cisplatin-induced membrane permeability changes. Our study is anticipated to lead to a methodology of screening anti-cancer drugs through their interactions with live cells.

Spatiotemporal norepinephrine mapping using a high-density CMOS microelectrode array

A high-density amperometric electrode array containing 8192 individually addressable platinum working electrodes with an integrated potentiostat fabricated using Complementary Metal Oxide Semiconductor (CMOS) processes is reported. The array was designed to enable electrochemical imaging of chemical gradients with high spatiotemporal resolution. Electrodes are arranged over a 2 mm × 2 mm surface area into 64 subarrays consisting of 128 individual Pt working electrodes as well as Pt pseudo-reference and auxiliary electrodes. Amperometric measurements of norepinephrine in tissue culture media were used to demonstrate the ability of the array to measure concentration gradients in complex media. Poly(dimethylsiloxane) microfluidics were incorporated to control the chemical concentrations in time and space, and the electrochemical response at each electrode was monitored to generate electrochemical heat maps, demonstrating the array's imaging capabilities. A temporal resolution of 10 ms can be achieved by simultaneously monitoring a single subarray of 128 electrodes. The entire 2 mm × 2 mm area can be electrochemically imaged in 64 seconds by cycling through all subarrays at a rate of 1 Hz per subarray. Monitoring diffusional transport of norepinephrine is used to demonstrate the spatiotemporal resolution capabilities of the system.

Single-Cell Migration as Studied by Scanning Electrochemical Microscopy

Scanning electrochemical microscopy (SECM) was used to study the migration of single live head and neck cancer cells (SCC25). The newly developed graphite paste ultramicroelectrode (UME) showed significantly less fouling in comparison to a 10 μm Pt-UME and thus could be used to monitor and track the migration pattern of a single cell. We also used SECM probe scan curves to measure the morphology (height and diameter) of a single live cancer cell during cellular migration and determined these dimensions to be 11 ± 4 μm and 40 ± 10 μm, respectively. The migration study revealed that cells within the same cell line had a heterogeneous migration pattern (migration and stationary) with an estimated migration speed of 8 ± 3 μm/h. However, serum-starved synchronized cells of the same line were found to have a non-heterogeneous cellular migration pattern with a speed of 9 ± 3 μm/h. Thus, this non-invasive SECM-based technique could potentially be expanded to other cell lines to study cellular biomechanics for improved understanding of the structure-function relationship at the level of a single cell.

Scanning Electrochemical Microscopy (SECM): Fundamentals and Applications in Life Sciences

In recent years, scanning electrochemical microscopy (SECM) has made significant contributions to the life sciences. Innovative developments focusing on high-resolution imaging, developing novel operation modes, and combining SECM with complementary optical or scanning probe techniques renders SECM an attractive analytical approach. This chapter gives an introduction to the essential instrumentation and operation principles of SECM for studying biologically-relevant systems. Particular emphasis is given to applications aimed at imaging the activity of biochemical constituents such as enzymes, antibodies, and DNA, which play a pivotal role in biomedical diagnostics. Furthermore, the unique advantages of SECM and combined techniques for studying live cells is highlighted by discussion of selected examples.

Functional Imaging of Chemically Active Surfaces with Optical Reporter Microbeads

We have developed a novel approach to allow for continuous imaging of concentration fields that evolve at surfaces due to release, uptake, and mass transport of molecules, without significant interference of the concentration fields by the chemical imaging itself. The technique utilizes optical “reporter” microbeads immobilized in a thin layer of transparent and inert hydrogel on top of the surface. The hydrogel has minimal density and therefore diffusion in and across it is like in water. Imaging the immobilized microbeads over time provides quantitative concentration measurements at each location where an optical reporter resides. Using image analysis in post-processing these spatially discrete measurements can be transformed into contiguous maps of the dynamic concentration field across the entire surface. If the microbeads are small enough relative to the dimensions of the region of interest and sparsely applied then chemical imaging will not noticeably affect the evolution of concentration fields. In this work colorimetric optode microbeads a few micrometers in diameter were used to image surface concentration distributions on the millimeter scale.

Simultaneous study of subcellular exocytosis with individually addressable multiple microelectrodes

We report the application of individually addressable microelectrode arrays (MEAs) to study the heterogeneity of cell exocytosis at the subcellular level. Multiple subcellular-size electrodes are covered by a single PC12 cell for the investigation of subcellular exocytosis. PC12 cells have been seeded and cultured on top of three kinds of MEAs containing 16, 25, or 36 square microelectrodes (4 μm width in a 4 by 4 MEA, 3 μm width in a 5 by 5 MEA, 2 μm width in a 6 by 6 MEA). After collagen coating, single cells were found to cover several electrodes and these were selected for the study of subcellular exocytosis. Amperometric results show that single cell and subcellular heterogeneity in single cell exocytosis can be electrochemically detected with these MEAs. The results also show that these MEAs are suitable for detecting fast chemical events at single cells, as well as for developing multifunctional electrochemical sensors.

Electrochemical push-pull probe: from scanning electrochemical microscopy to multimodal altering of cell microenvironment

To understand biological processes at the cellular level, a general approach is to alter the cells' environment and to study their chemical responses. Herein, we present the implementation of an electrochemical push-pull probe, which combines a microfluidic system with a microelectrode, as a tool for locally altering the microenvironment of few adherent living cells by working in two different perturbation modes, namely electrochemical (i.e., electrochemical generation of a chemical effector compound) and microfluidic (i.e., infusion of a chemical effector compound from the pushing microchannel, while simultaneously aspirating it through the pulling channel, thereby focusing the flow between the channels). The effect of several parameters such as flow rate, working distance, and probe inclination angle on the affected area of adherently growing cells was investigated both theoretically and experimentally. As a proof of concept, localized fluorescent labeling and pH changes were purposely introduced to validate the probe as a tool for studying adherent cancer cells through the control over the chemical composition of the extracellular space with high spatiotemporal resolution. A very good agreement between experimental and simulated results showed that the electrochemical perturbation mode enables to affect precisely only a few living cells localized in a high-density cell culture.

Development of a versatile in vitro platform for studying biological systems using micro-3D printing and scanning electrochemical microscopy

We report a novel strategy for studying a broad range of cellular behaviors in real time by combining two powerful analytical techniques, micro-3D printing and scanning electrochemical microscopy (SECM). This allows one, in microbiological studies, to isolate a known number of cells in a micrometer-sized chamber with a roof and walls that are permeable to small molecules and observe metabolic products. In such studies, the size and spatial organization of a population play a crucial role in cellular group behaviors, such as intercellular interactions and communication. Micro-3D printing, a photolithographic method for constructing cross-linked protein microstructures, permits one to compartmentalize a small population of microbes by forming a porous roof and walls around cells in situ. Since the roof and walls defining the microchamber are porous, any small molecules can freely diffuse from the chamber to be detected and quantified using SECM. The size of the chamber and the roof permeability can be obtained by SECM using a small probe molecule, ferrocenemethanol (FcMeOH). The chamber permeability to FcMeOH can be tuned by varying printing parameters that influence the cross-linking density of the proteinaceous material. These analyses establish a versatile strategy as a sensitive platform to quantitatively monitor small molecules produced by microbes.

Quantitative and real-time effects of carbon quantum dots on single living HeLa cell membrane permeability

The interaction between carbon quantum dots (CQDs) and a single living cell was explored in real time. Here, we provide the quantitative data on the permeability of the HeLa cell membrane in the presence of CQDs with different surface functional groups (CQDs terminated with -OH/-COOH (CQD-OH), -PEG (CQD-PEG), and -NH2 (CQD-NH2)). Although these CQDs have very low toxicity towards HeLa cells, they still increase the cell membrane permeability by 8%, 13%, and 19% for CQD-PEG, CQD-OH, and CQD-NH2, respectively, and this kind of permeability was irreversible. These observations are valuable for promoting the bio-applications of carbon nanostructures in living systems.

Nanopipette exploring nanoworld

Nanopipettes, with tip orifices on the order of tens to hundreds of nanometers, have been utilized in the fields of analytical chemistry and nanophysiology. Nanopipettes make nanofabrication possible at liquid/solid interfaces. Moreover, they are utilized in time-resolved measurements and for imaging biological materials, e.g., living cells, by using techniques such as scanning ion-conductance microscopy and scanning electrochemical microscopy. We have successfully fabricated ion-selective nanopipettes that can be used to identify targeted ions such as sodium and potassium in- and outside of living cells. In this review, we discuss the extent of utilization of nanopipettes in investigating the nanoworld. In addition, we discuss the potential applications of future nanopipettes.

A time course study of cadmium effect on membrane permeability of single human bladder cancer cells using scanning electrochemical microscopy

Cd(2+) is carcinogenic to both humans and experimental animals. We present quantitative time-course imaging of Cd(2+)-induced variation in the membrane permeability of single live human bladder cancer cells (T24) to ferrocenemethanol using scanning electrochemical microscopy (SECM). High temporal resolution combined with non-invasive nature renders a time-lapse SECM depth scan, a promising method to quantitatively investigate the effectiveness, kinetics, and mechanism of metal ions based on the responses of single live cells in real time. Under unstimulated conditions, T24 cells have constant membrane permeability to ferrocenemethanol of approximately 5.0×10(-5) m/s. When cadmium is added in-situ to T24 cells, the membrane permeability increases up to 3.5×10(-4) m/s, allowing more flux of ferrocenemethanol to the ultramicroelectrode tip. This suggests an increased spreading between the phospholipid heads in the cytoplasmic membrane. Membrane permeability might be used as a measure to probe cell status in practical intoxication cases. The methodology reported here can be applied to many other metals and their interactions with extracellular biomolecules, leading insights into cell physiology and pathobiology.

Investigating catalase activity through hydrogen peroxide decomposition by bacteria biofilms in real time using scanning electrochemical microscopy

Catalase activity through hydrogen peroxide decomposition in a 1 mM bulk solution above Vibrio fischeri (γ-Protebacteria-Vibrionaceae) bacterial biofilms of either symbiotic or free-living strains was studied in real time by scanning electrochemical microscopy (SECM). The catalase activity, in units of micromoles hydrogen peroxide decomposed per minute over a period of 348 s, was found to vary with incubation time of each biofilm in correlation with the corresponding growth curve of bacteria in liquid culture. Average catalase activity for the same incubation times ranging from 1 to 12 h was found to be 0.28 ± 0.07 μmol H2O2/min for the symbiotic biofilms and 0.31 ± 0.07 μmol H2O2/min for the free-living biofilms, suggesting similar catalase activity. Calculations based on Comsol Multiphysics simulations in fitting experimental biofilm data indicated that approximately (3 ± 1) × 10(6) molecules of hydrogen peroxide were decomposed by a single bacterium per second, signifying the presence of a highly active catalase. A 2-fold enhancement in catalase activity was found for both free-living and symbiotic biofilms in response to external hydrogen peroxide concentrations as low as 1 nM in the growth media, implying a similar mechanism in responding to oxidative stress.

Use of combined scanning electrochemical and fluorescence microscopy for detection of reactive oxygen species in prostate cancer cells

Release of ROS from prostate cancer (PC3) cells was studied using scanning electrochemical microscopy (SECM) and fluorescence microscopy. One-directional lateral scan SECM was used as a rapid and reproducible tool for simultaneous mapping of cell topography and reactive oxygen species (ROS) release. Fluorescence microscopy was used in tandem to monitor the tip position, in addition to providing information on intracellular ROS content via the use of ROS-reactive fluorescent dyes. A unique tip current (iT) vs lateral distance profile was observed when the tip potential (ET) was set at -0.65 V. This profile reflects the combined effects of topographical change and ROS release at the PC3 cell surfaces. Differentiation between topographical-related and ROS-induced current change was achieved by comparing the scans collected at -0.65 and -0.85 V. The effects of other parameters such as tip to cell distance, solvent oxygen content, and scan direction on the profile of the scan were systematically evaluated. Cells treated with tert-butyl hydroperoxide, a known ROS stimulus, were also evaluated using the lateral scanning approach. Overall, the SECM results correlate well with the fluorescence results. The extracellular ROS level detected at the SECM tip was found to be similar to the intracellular ROS level monitored using fluorescence microscopy. While the concentration of each contributing ROS species has not been determined and is thus part of the future study, here we have successfully demonstrated the use of a simple two-potential lateral scan approach for analysis of ROS released by living cells under real physiological conditions.

Super-resolved FT-IR spectroscopy: Strategies, challenges, and opportunities for membrane biophysics

Direct correlation of molecular conformation with local structure is critical to studies of protein- and peptide-membrane interactions, particularly in the context of membrane-facilitated aggregation, and disruption or disordering. Infrared spectroscopy has long been a mainstay for determining molecular conformation, following folding dynamics, and characterizing reactions. While tremendous advances have been made in improving the spectral and temporal resolution of infrared spectroscopy, it has only been with the introduction of scanned-probe techniques that exploit the raster-scanning tip as either a source, scattering tool, or measurement probe that researchers have been able to obtain sub-diffraction limit IR spectra. This review will examine the history of correlated scanned-probe IR spectroscopies, from their inception to their use in studies of molecular aggregates, membrane domains, and cellular structures. The challenges and opportunities that these platforms present for examining dynamic phenomena will be discussed. This article is part of a Special Issue entitled: FTIR in membrane proteins and peptide studies.

Nanoscale mechanism of molecular transport through the nuclear pore complex as studied by scanning electrochemical microscopy

The nuclear pore complex (NPC) is the proteinaceous nanopore that solely mediates molecular transport across the nuclear envelope between the nucleus and cytoplasm of a eukaryotic cell. Small molecules (<40 kDa) diffuse through the large pore of this multiprotein complex. A passively impermeable macromolecule tagged with a signal peptide is chaperoned through the nanopore by nuclear transport receptors (e.g., importins) owing to their interactions with barrier-forming proteins. Presently, this bimodal transport mechanism is not well understood and is described by controversial models. Herein, we report on a dynamic and spatially resolved mechanism for NPC-mediated molecular transport through nanoscale central and peripheral routes with distinct permeabilities. Specifically, we develop a nanogap-based approach of scanning electrochemical microscopy to precisely measure the extremely high permeability of the nuclear envelope to a small probe molecule, (ferrocenylmethyl)trimethylammonium. Effective medium theories indicate that the passive permeability of 5.9 × 10(-2) cm/s corresponds to the free diffusion of the probe molecule through ~22 nanopores with a radius of 24 nm and a length of 35 nm. Peripheral routes are blocked by wheat germ agglutinin to yield 2-fold lower permeability for 17 nm-radius central routes. This lectin is also used in fluorescence assays to find that importins facilitate the transport of signal-tagged albumin mainly through the 7 nm-thick peripheral route rather than through the sufficiently large central route. We propose that this spatial selectivity is regulated by the conformational changes in barrier-forming proteins that transiently and locally expand the impermeably thin peripheral route while blocking the central route.

Recent advances in high resolution scanning electrochemical microscopy of living cells--a review

This review discusses advances in the field of high resolution scanning electrochemical microscopy (HR-SECM) and scanning ion conductance microscopy (SICM) to study living cells. Relevant references from the advent of this technique in the late 1980s to most recent contributions in 2012 are presented with special discussion on high resolution images. A clear progress especially within the last 5 years can be seen in the field of HR-SECM. Furthermore, we also concentrate on the intrinsic properties of SECM imaging techniques e.g. different modes of image acquisition, their advantages and disadvantages in imaging living cells and strategies for further enhancement of image resolution, etc. Some of the recent advances of SECM in nanoimaging have also been discussed which may have potential applications in high resolution imaging of cellular processes.

Filming a live cell by scanning electrochemical microscopy: label-free imaging of the dynamic morphology in real time

The morphology of a live cell reflects the organization of the cytoskeleton and the healthy status of the cell. We established a label-free platform for monitoring the changing morphology of live cells in real time based on scanning electrochemical microscopy (SECM). The dynamic morphology of a live human bladder cancer cell (T24) was revealed by time-lapse SECM with dissolved oxygen in the medium solution as the redox mediator. Detailed local movements of cell membrane were presented by time-lapse cross section lines extracted from time-lapse SECM. Vivid dynamic morphology is presented by a movie made of time-lapse SECM images. The morphological change of the T24 cell by non-physiological temperature is in consistence with the morphological feature of early apoptosis. To obtain dynamic cellular morphology with other methods is difficult. The non-invasive nature of SECM combined with high resolution realized filming the movements of live cells.

Temporal resolution in electrochemical imaging on single PC12 cells using amperometry and voltammetry at microelectrode arrays

Carbon-fiber-microelectrode arrays (MEAs) have been utilized to electrochemically image neurochemical secretion from individual pheochromocytoma (PC12) cells. Dopamine release events were electrochemically monitored from seven different locations on single PC12 cells using alternately constant-potential amperometry and fast-scan cyclic voltammetry (FSCV). Cyclic voltammetry, when compared to amperometry, can provide excellent chemical resolution; however, spatial and temporal resolution are both compromised. The spatial and temporal resolution of these two methods have been quantitatively compared and the differences explained using models of molecular diffusion at the nanogap between the electrode and the cell. A numerical simulation of the molecular flux reveals that the diffusion of dopamine molecules and electrochemical reactions both play important roles in the temporal resolution of electrochemical imaging. The simulation also reveals that the diffusion and electrode potential cause the differences in signal crosstalk between electrodes when comparing amperometry and FSCV.

Redox reactions of reactive oxygen species in aqueous solutions as the probe for scanning electrochemical microscopy of single live T24 cells

The redox reactions of two main components of reactive oxygen species (ROS), superoxide and hydrogen peroxide, along with oxygen in aqueous solutions were investigated using a conventional electrochemical technique, differential pulse voltammetry (DPV). Superoxide undergoes oxidation at a Pt working electrode biased at 0.055 V versus Ag/AgCl, while hydrogen peroxide can be oxidized and reduced at 0.817 and –0.745 V, respectively. Oxygen in the solutions is reduced at the electrode with an applied potential of –0.455 V. Based on these results, hydrogen peroxide and superoxide released from live cells can be successfully monitored, identified, and mapped using scanning electrochemical microscopy (SECM) at different potentials. Single human bladder (T24) cells were imaged using a 5 μm diameter SECM probe biased at –0.400, –0.600, and –0.800 V. Oxygen reduction that seems an interference can be discriminated from that of hydrogen peroxide by means of SECM.

Influence of electrode size and geometry on electrochemical experiments with combined SECM-SFM probes

Gold electrodes integrated into silicon scanning force microscopy (SFM) probes allow the acquisition of spatially correlated data for sample morphology (via SFM) and local electrochemical reactivity via scanning electrochemical microscopy (SECM). The lateral resolution of both techniques is controlled by different properties of the integrated probes. The topographic tracking provided by the SFM mechanism allows the realization of very small working distances for the SECM measurements. Microfabrication technology was used in order to reduce the size of the active electrode area of the tip into the sub-100 nm regime. The functionality of the probes was tested using electrochemical methods. Experiments revealed that the response could be quantitatively compared to numerical simulation. The low working distance, in combination with the small size of the active electrode area, allows for high lateral resolution in the SECM images. This is illustrated with different model substrates that cover a range of different rate constants and illustrate the dependence of the SECM contrast on the local kinetics of the sample in the sub-micrometre size range.

Scanning electrochemical microscopy in neuroscience

This article reviews recent work involving the application of scanning electrochemical microscopy (SECM) to the study of individual cultured living cells, with an emphasis on topographical and functional imaging of neuronal and secretory cells of the nervous and endocrine system. The basic principles of biological SECM and associated negative amperometric-feedback and generator/collector-mode SECM imaging are discussed, and successful use of the methodology for screening soft and fragile membranous objects is outlined. The drawbacks of the constant-height mode of probe movement and the benefits of the constant-distance mode of SECM operation are described. Finally, representative examples of constant-height and constant-distance mode SECM on a variety of live cells are highlighted to demonstrate the current status of single-cell SECM in general and of SECM in neuroscience in particular.