Hybridization detection of enzyme-labeled DNA at electrically heated electrodes

Heating promoted super sensitive electrochemical detection of p53 gene based on alkaline phosphatase and nicking endonuclease Nt.BstNBI-assisted target recycling amplification strategy at heated gold disk electrode

An ultrasensitive electrochemical biosensor for detecting p53 gene was fabricated based on heated gold disk electrode coupling with endonuclease Nt.BstNBI-assisted target recycle amplification and alkaline phosphatase (ALP)-based electrocatalytic signal amplification. For biosensor assembling, biotinylated ssDNA capture probes were first immobilized on heated Au disk electrode (HAuDE), then combined with streptavidin-alkaline phosphatase (SA-ALP) by biotin-SA interaction. ALP could catalyze the hydrolysis of ascorbic acid 2-phosphate (AAP) to produce ascorbic acid (AA). While AA could induce the redox cycling to generate electrocatalytic oxidation current in the presence of ferrocene methanol (FcM). When capture probes hybridized with p53, Nt.BstNBI would recognize and cleave the duplexes and p53 was released for recycling. Meanwhile, the biotin group dropt from the electrode surface and subsequently SA-ALP could not adhere to the electrode. The signal difference before and after cleavage was proportional to the p53 gene concentration. Furthermore, with electrode temperature elevated, the Nt.BstNBI and ALP activities could be increased, greatly improving the sensitivity and efficiency for p53 detection. A detection limit of 9.5 × 10^-17 M could be obtained (S/N = 3) with an electrode temperature of 40 °C, ca. four magnitudes lower than that at 25 °C.

Scanning Electrochemical Microscopy of Electrically Heated Wire Substrates

We report a new configuration for enhancing the performance of scanning electrochemical microscopy (SECM) via heating of the substrate electrode. A flattened Pt microwire was employed as the substrate electrode. The substrate was heated by an alternating current (AC), resulting in an increased mass transfer between the wire surface and the bulk solution. The electrochemical response of the Pt wire during heating was investigated by means of cyclic voltammetry (CV). The open circuit potential (OCP) of the wire was recorded over time, while varied heating currents were applied to investigate the time needed for establishing steady-state conditions. Diffusion layer studies were carried out by performing probe approach curves (PACs) for various measuring modes of SECM. Finally, imaging studies of a heated substrate electrode surface, applying feedback, substrate generation/tip collection (SG/TC), and the competition mode of SECM, were performed and compared with room temperature results.

Temperature-Controllable Electrodes with a One-Parameter Calibration

Electrically heated electrodes have been applied for various chemical and biological sensors. However, previous electrically heated electrodes, including microwires and microdiscs, are usually small and often suffer from the requirement of frequent calibrations of the electrode surface temperature ( T_s) at different environment temperatures. Here, we fabricate a temperature-controllable disk electrode (TCDE) with a conventional size (3-5 mm in diameter). A one-parameter temperature calibration is proposed using a temperature transfer coefficient α and a structural model ( T_s = T_e + α ( T_h - T_e)) to estimate T_s ( T_h and T_e are the temperature of the heating element and environment, respectively). The value of α is unique for a TCDE and mainly dependent on the structure and materials of the electrodes and the solution in nature. Once α is experimentally determined, T_s can be calibrated and found to be applicable to wide fluctuations in room temperature (15.0-33.0 °C) with errors below 1.5% for three types of disk electrodes (gold, glassy carbon, and platinum). The required T_s can be obtained by just setting T_h without thermal characterization between the heating power and T_s. A simple relationship for exploring the dependence of α on the height ( H) and radius ( R) of the electrode materials and other constants ( a, b, c, and R₀), α = 1 - c - aH - b ( R - R₀)², is revealed by numerical simulations (COMSOL). The impact of the radii of both the insulating materials of the electrode and the electrochemical cells on T_s is also considered. The effect of the solution thermal conductivity on α is studied. TCDEs are expected to be used as a sensor platform with enhanced performance.

Hairpin-based DNA electrochemical sensor for selective detection of a repetitive and structured target codifying a gliadin fragment

High selectivity of genosensors is crucial for certain applications such as those involving species with high genetic variability. This is an unresolved problem when dealing with long target sequences that is further complicated when the target contains repetitive sequence domains. As a model for this situation, the problem of detecting gluten in food with identification of the source is studied. In order to discriminate the specific DNA sequence that encodes the wheat prolamin (gliadin) from rye and barley prolamins, the exquisite selectivity of a rationally designed hairpin capture probe is proposed and compared to a nonstructured capture probe. An electrochemical sandwich assay is proposed, involving capture probes chemisorbed on Au surfaces and biotinylated-signaling probes in combination with streptavidin-peroxidase labeling conjugates. As a result, a genosensor with similar sensitivity to that observed with linear probes but with complete specificity against closely related species was achieved. The surface-attached DNA stem-loop yields a device capable of accurately discriminating wheat DNA from rye and barley with a limit of detection of 1 nM.

Electrochemical DNA hybridization sensors based on conducting polymers

Conducting polymers (CPs) are a group of polymeric materials that have attracted considerable attention because of their unique electronic, chemical, and biochemical properties. This is reflected in their use in a wide range of potential applications, including light-emitting diodes, anti-static coating, electrochromic materials, solar cells, chemical sensors, biosensors, and drug-release systems. Electrochemical DNA sensors based on CPs can be used in numerous areas related to human health. This review summarizes the recent progress made in the development and use of CP-based electrochemical DNA hybridization sensors. We discuss the distinct properties of CPs with respect to their use in the immobilization of probe DNA on electrode surfaces, and we describe the immobilization techniques used for developing DNA hybridization sensors together with the various transduction methods employed. In the concluding part of this review, we present some of the challenges faced in the use of CP-based DNA hybridization sensors, as well as a future perspective.