Electrically controlled variation of receptor affinity

Chemosensitive Properties of Electrochemically Synthesized Poly-3-Thienylboronic Acid: Conductometric Detection of Glucose and Other Diol-Containing Compounds under Electrical Affinity Control

Due to the presence of the boronic acid moieties, poly-3-thienylboronic acid has an affinity for saccharides and other diol-containing compounds. Thin films of this novel chemosensitive polymer were synthesized electrochemically on the gold surface. The adhesion of the polymer was enhanced by the deposition of a monomolecular layer of thiophenol. The technology was used to fabricate conductometric sensors for glucose and other diol-containing compounds. Simultaneous two- and four-electrode conductivity measurements were performed. The chemical sensitivity to sorbitol, fructose, glucose, and ethylene glycol was studied at different pH and electrode potentials, and the corresponding binding constants were obtained. Depending on the electrode potential, the reciprocal values of the binding constants of glucose to poly-3-thienylboronic acid at neutral pH are in the range of 0.2 mM-1.0 mM. The affinity for glucose has been studied in buffer solutions and in solutions containing the major components of human blood. It was shown that the presence of human serum albumin increases the affinity of poly-3-thienylboronic acid for diol-containing compounds.

Array of Miniaturized Amperometric Gas Sensors Using Atomic Gold Decorated Pt/PANI Electrodes in Room Temperature Ionic Liquid Films

Miniaturized sensors possess many advantages, such as rapid response, easy chip integration, a possible lower concentration of target compound detection, etc. However, a major issue reported is a low signal response. In this study, a catalyst, the atomic gold clusters of Au_n where n = 2, was decorated at a platinum/polyaniline (Pt/PANI) working electrode to enhance the sensitivity of butanol isomers gas measurement. Isomer quantification is challenging because this compound has the same chemical formula and molar mass. Furthermore, to create a tiny sensor, a microliter of room-temperature ionic liquid was used as an electrolyte. The combination of the Au₂ clusters decorated Pt/PANI and room temperature ionic liquid with several fixed electrochemical potentials was explored to obtain a high solubility of each analyte. According to the results, the presence of Au₂ clusters increased the current density due to electrocatalytic activity compared to the electrode without Au₂ clusters. In addition, the Au₂ clusters on the modified electrode had a more linear concentration dependency trend than the modified electrode without atomic gold clusters. Finally, the separation among butanol isomers was enhanced using different combination of room-temperature ionic liquids and fixed potentials.

3-Thienylboronic Acid as a Receptor for Diol-Containing Compounds: A Study by Isothermal Titration Calorimetry

The electrochemical activity of 3-thienylboronic acid and its feature to form polymer films makes it a perspective receptor material for sensor applications. The affinity properties of this compound were studied here by isothermal titration calorimetry. A number of different analytes were tested, and the highest binding enthalpy was observed for sorbitol and fructose. An increase of pH in the range of 5.5–10.6 results in the rise of the binding enthalpy with an increase of the binding constant to ~8400 L/mol for sorbitol or ~3400 L/mol for fructose. The dependence of the binding constant on pH has an inflection point at pH 7.6 with a slope that is a ten-fold binding constant per one pH unit. The binding properties of 3-thienylboronic acid were evaluated to be very close to that of the phenylboronic acid, but the electrochemical activity of 3-thienylboronic acid provides a possibility of external electrical control: dependence of the affinity of 3-thienylboronic acid on its redox state defined by the presence of ferro/ferricyanide in different ratios was demonstrated. The results show that 3-thienylboronic acid can be applied in smart chemical sensors with electrochemically controllable receptor affinity.

Poly-3-thienylboronic acid: a chemosensitive derivative of polythiophene

Poly-3-thiopheneboronic acid was synthesized by electrochemical polymerization from 3-thienylboronic acid dissolved in the mixture of boron trifluoride diethyl etherate and acetonitrile. Cyclic voltammetry during electropolymerization shows oxidative and reductive peaks growing in each next cycle. An investigation by scanning electron microscopy displayed the polymer layer like a highly flexible film of 110 nm thick with grains of 60–120 nm in size. Strong negative solvatochromic effect was observed. Optical spectra of poly-3-thienylboronic acid at different potentials and pH were studied. Potential cycling leads to a well reversible electrochromic effect. At pH 7.4, the increase of potential leads to the decrease in the absorption band at 480 nm and to the rise in the absorption band at 810 nm with an isosbestic point at 585 nm. Spectroelectrochemical behavior of poly-3-thienylboronic acid and polythiophene was compared. Binding of sorbitol at fixed electrode potential leads to an increase in the absorbance in the shortwave band and to the decrease in the longwave band; the effect depends on the electrode potential and pH. Perspectives of application of poly-3-thienylboronic acid as new chemosensitive material are discussed.