Rapid and sensitive analysis of progesterone by solid-phase extraction with amino-functionalized metal-organic frameworks coupled to direct analysis in real-time mass spectrometry

Applications of metal organic frameworks in dispersive micro solid phase extraction (D-μ-SPE)

Metal-organic frameworks (MOFs) are a fascinating family of crystalline porous materials made up of metal clusters and organic linkers. In comparison with other porous materials, MOFs have unique characteristics including high surface area, homogeneous open cavities, and permanent high porosity with variable shapes and sizes. For these reasons, MOFs have recently been explored as sorbents in sample preparation by solid-phase extraction (SPE). However, SPE requires large amounts of sorbents and suffers from limited contact surfaces with analytes, which compromises extraction recovery and efficiency. Dispersive SPE (D-SPE) overcomes these limitations by dispersing the sorbents into the sample, which in turn increases contact with the analytes. Miniaturization of the microextraction procedure, particularly the amount of sorbent reduces the amount consumed of the organic solvent and shorten the time required to attain the equilibrium state. This may explain the reported high efficiency and applicability of MOFs in dispersive micro SPE (D-µ-SPE). This method retains all the advantages of solid phase extraction while also being simpler, faster, cheaper, and, in some cases, more effective in comparison with D-SPE. Besides, D-µ-SPE requires smaller amounts of the sorbents which reduces the overall cost, and the amount of waste generated from the analytical process. In this review, we discuss the applications of MOFs in D-µ-SPE of various analytes including pharmaceuticals, pesticides, organic dyes from miscellaneous matrices including water samples, biological samples and food samples.

Preparation of a sustainable magnetic sorbent for the extraction and preconcentration of progestogens in natural water samples

A film composed of agarose and graphene (G) and magnetic nanoparticles (G-MNPs) is proposed as a sorbent for the extraction and determination of medroxyprogesterone (MED), levonorgestrel (LEV), norethisterone (NOR) and progesterone (PRO) in natural water samples. Both the preparation of the film and the extraction procedure were optimized. The optimal extraction parameters were as follows: isopropyl alcohol as activation solvent, sample pH value of 3.0, extraction time of 30 min, 1.00 mL of acetonitrile as eluent, elution time of 5 min and sample volume of 100.00 mL. HPLC with photodiode array detector was used for the separation and determination. The method presented a linear range between 2.50 and 75.0 μg L-1 for all analytes, and the LODs were between 1.40 and 1.80 μg L-1. The method was applied to natural water samples, obtaining satisfactory recovery values (75-111 %). In conclusion, for the immobilization of the G-MNPs, agarose was used, which is a non-toxic, renewable and biodegradable material. The G-MNPs-agarose film was reused up to 70 times, without losing its extraction capacity significantly and presenting excellent sorbent properties, which allow the extraction and preconcentration of the progestogens under study.

Urine Metabolites and Bioactive Compounds from Functional Food: Applications of Liquid Chromatography Mass Spectrometry

Bioactive compounds in functional foods, medicinal plants and others are considered attractive value-added molecules based on their wide range of bioactivity. It is clear that an important role is occupied by polyphenol, phenolic compounds and others. Urine is an effective biofluid to evaluate and monitor alterations in homeostasis and other processes related to metabolism. The current review provides a detailed description of the formation of urine in human body, various aspects relevant to sampling and analysis of urinary metabolites before presenting recent developments leveraging on metabolite profiling of urine. For the profiling of small molecules in urine, advancement of liquid chromatography mass tandem spectrometry (LC/MS/MS), establishment of standardized chemical fragmentation libraries, computational resources, data-analysis approaches with pattern recognition tools have made it an attractive option. The profiling of urinary metabolites gives an overview of the biomarkers associated with the diet and evaluates its biological effects. Metabolic pathways such as glycolysis, tricarboxylic acid cycle, amino acid metabolism, energy metabolism, purine metabolism and others can be evaluated. Finally, a combination of metabolite profiling with chemical standardization and bioassay in functional food and medicinal plants will likely lead to the identification of new biomarkers and novel biochemical insights.

Online coupling of matrix solid-phase dispersion to direct analysis in real time mass spectrometry for high-throughput analysis of regulated chemicals in consumer products

The current work is the first study on online coupling of matrix solid-phase dispersion (MSPD) to direct analysis in real time mass spectrometry (DART-MS) bridging with solid-phase analytical derivatization (SPAD) based on a graphene oxide nanosheets (GONs)-coated cotton swab. Proof-of-concept demonstrations were explored for high-throughput analysis of a diversity of regulated chemicals in consumer products such as textiles, toys, and cosmetics. On-demand sorbent combinations were blended with samples, packed into MSPD columns, and mounted on a homemade 3D-printed rack module for automated sample feeding. To achieve good synergy between MSPD and DART-MS, a cotton swab with a conical tip deposited with GONs was attached to the bottom of the MSPD column. The swabs serve as a solid-phase microextraction probe for convenient enrichment of the eluted analytes from MSPD, thermal desorption of the enriched analytes by DART, and sensitive detection by a hybrid quadrupole-Orbitrap mass spectrometer. Furthermore, the utility of an on-swab SPAD strategy was demonstrated for the detection of formaldehyde by use of the derivatizing reagent of dansyl hydrazine, contributing to improved ionization efficiency without compromising the overall coherence of the analytical workflow. The MSPD-DART-MS methodology was systematically optimized and validated, obtaining acceptable recovery (71.7-110.3%), repeatability (11.8-19.3%), and sensitivity (limits of detection and quantitation in the ranges of 6.2-19.5 and 23.7-75.9 μg/kg) for 32 target analytes. The developed protocol streamlined sample extraction, clean-up, desorption, ionization, and detection, highlighting the appealing potential for high-throughput analysis of samples with complex matrices.

Natural Deep Eutectic Solvent-Based Dispersive Liquid-Liquid Microextraction Coupled with Direct Analysis in Real Time Mass Spectrometry: A Green Temperature-Mediated Analytical Strategy

Green analytical chemistry (GAC) represents a rapidly growing research field that aims at developing novel analytical approaches with minimal consumption of hazardous reagents and solvents. The current study reports on a GAC methodology exploiting the unique physicochemical properties of natural deep eutectic solvents (NADESs), a supposedly environmentally friendly class of solvents. Based on a temperature-mediated strategy, the NADESs were manipulated to undergo multiple phase transitions for favorable functionality and performance. As proof-of-concept demonstrations, both hydrophobic and hydrophilic NADESs were prepared for the extraction and analysis of eight phthalate esters in aqueous samples (food simulants) and three aflatoxins in oily samples (edible oils), respectively. NADES-based dispersive liquid-liquid microextraction (DLLME) was employed to achieve high-efficiency sample pretreatment. Afterward, the NADESs were transformed from liquids into solids by tuning the peripheral temperature for a convenient phase separation from the sample matrices. The solidified NADES extracts were melted and vaporized at elevated temperatures by transmission-mode direct analysis in real time (DART) for further quadrupole-Orbitrap high-resolution mass spectrometry (Q-Orbitrap HRMS) analysis. The developed protocol was validated, achieving good repeatability with relative standard deviations (RSDs) of less than 9% and satisfactory sensitivity with limits of detection (LODs) and quantitation (LOQs) ranging from 0.1 to 0.8 and 0.2 to 2.0 μg/kg, respectively. The greenness of the analytical methodology was assessed with the calculated scores of 0.66 and 0.57 for the hydrophobic and hydrophilic NADES-based protocols, respectively. The method was applied to marketed samples, highlighting the great potential for green chemical analysis.

Rapid analysis of differential chemical compositions of Poria cocos using thin-layer chromatography spray ionization-mass spectrometry

A simple analytical strategy for determining the chemical composition of Poria cocos using thin-layer chromatography spray ionization-mass spectrometry (TLCSI-MS).

Methacrylic functionalized hybrid carbon nanomaterial for the selective adsorption and detection of progesterone in wastewater

Progesterone, an endocrine-disrupting chemical, has been frequently detected in wastewater for decades, posing a serious threat to ecological and human health. However, it is still a challenge to achieve the effective detection of progesterone in complex matrices water samples. In this study, a novel adsorbent CNT@CS/P(MAA) was prepared by grafting methacrylic polymers on the surface of modified carbon nanomaterials. Compared with other reported materials, the hybrid carbon nanomaterial could selectively identify the progesterone in the complex industrial pharmaceutical wastewater, and its adsorption performance is almost independent of the pH and environmental temperature. In addition, this nanomaterial could be reused with a good recovery rate. The prepared nanomaterials were characterized by transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, nitrogen adsorption and desorption experiments, and thermogravimetric analysis. The results confirmed that the methacrylic polymers and chitosan layer were successfully grafted on the surface of carbon nanotubes. Adsorption isotherms, adsorption kinetics, and selectivity tests showed that CNT@CS/P(MAA) had a high adsorption capacity (44.45 mg·g-1), a fast adsorption rate and a satisfied selectivity for progesterone. Then, CNT@CS/P(MAA) was used as solid phase extraction sorbent and combined with HPLC to enrich progesterone from the wastewater samples. Under the optimum conditions, a good linearity was obtained with the correlation coefficient was 0.9998, and the limit of detection was 0.003 ng·mL-1. Therefore, this method could be used for the selective and effective detection of progesterone in industrial wastewater with complex substrates and provided a new method for the detection of progesterone in other environmental waters.

Characterization of natural herbal medicines by thin-layer chromatography combined with laser ablation-assisted direct analysis in real-time mass spectrometry

The characterization and quality control of natural herbal medicines, such as traditional Chinese medicines (TCMs), is of great significance to ensure their potential efficacy and avoid severe side effects. Thin-layer chromatography (TLC) is a simple and classic approach for examining quality marker of natural products. Nevertheless, it is more difficult to further characterize the compounds adsorbed on the TLC plate. Herein, we reported a simple setup of laser ablation-assisted direct analysis in real-time mass spectrometry (LA-DART-MS), in which the coupling of mass spectrometry information to provide a predominant dimension in the identification of unknown chemical compositions separated on standard TLC plates, and it was applied for rapid characterization of various kinds of natural herbal medicines. The results showed that the introduction of low-cost small laser pointer had significantly improved the desorption process. The system was successfully applied in the analysis of alkaloids, flavonoids, anthraquinones, volatile oils, glycosides, organic acids, and eight different TCMs including Sophorae Flavescentis Radix, Angelicae Sinensis Radix, Acori Tatarinowii Rhizoma, Phellodendri Chinensis Cortex, Picrasmae Ramulus et Folium, Gynura Japonica, Rhei Radix et Rhizoma and Dendrobii Caulis. The obtained limits of detection (LODs) of this method for various types of reference substances were in the range of 4.6-162.2 ng/band on TLC plates. Furthermore, the quality control and identification of different species of Dendrobii Caulis herb was achieved. This study combines the advantages of TLC and ambient mass spectrometry to provide a good choice for the screening and identification of active ingredients and the quality evaluation of botanical samples.

Porous Inorganic Materials for Bioanalysis and Diagnostic Applications

Porous inorganic materials play an important role in adsorbing targeted analytes and supporting efficient reactions in analytical science. The detection performance relies on the structural properties of porous materials, considering the tunable pore size, shape, connectivity, etc. Herein, we first clarify the enhancement mechanisms of porous materials for bioanalysis, concerning the detection sensitivity and selectivity. The diagnostic applications of porous material-assisted platforms by coupling with various analytical techniques, including electrochemical sensing, optical spectrometry, and mass spectrometry, etc., are then reviewed. We foresee that advanced porous materials will bring far-reaching implications in bioanalysis toward real-case applications, especially as diagnostic assays in clinical settings.

Novel solid-phase extraction filter based on a zirconium meta-organic framework for determination of non-steroidal anti-inflammatory drugs residues

In this study, a zirconium-based metal-organic framework UiO-66-NH₂ modified cotton fiber (CF@UiO-66-NH₂) was fabricated for the extraction of five common NSAIDs, namely ketoprofen, naproxen, flurbiprofen, diclofenac sodium, and ibuprofen. UiO-66-NH₂ was synthesized and immobilized on the surface of cotton fiber using an environmentally friendly aqueous synthesis method. The prepared CF@UiO-66-NH₂ composite of 50 mg was loaded into a 13 mm recessed filter for use as a solid-phase extraction (SPE) adsorbent material. The filter was then used to enrich NSAIDs in fish and shrimp muscle tissues followed by ultra-high performance liquid chromatography (UPLC) detection. Several key parameters were evaluated and optimized, including adsorption flow rate, pH value of sample, desorption flow rate, and the formic acid content of the eluent. Under optimized conditions, linear ranges of ketoprofen, naproxen, flurbiprofen, diclofenac sodium, and ibuprofen were 2.0-300.0 ng/mL, 1.4-280.0 ng/mL, 3.0-400.0 ng/mL, 1.0-500.0 ng/mL, and 14.0-560.0 ng/mL, respectively. The detection limits ranged from 0.12 ng/mL to 3.50 ng/mL with recoveries in the range of 72.95-116.99%, RSDs < 9.90%. The results demonstrated that the homemade filters based on CF@UiO-66-NH₂ exhibited good reproducibility, stability and adsorption property for the determination of trace-level NSAIDs in complex matrix.

Green bioanalytical sample preparation: fabric phase sorptive extraction

Fabric phase sorptive extraction (FPSE) is a recently introduced sample preparation technique that has attracted substantial interest of the scientific community dealing with bioanalysis. This technique is based on a permeable and flexible substrate made of fabric, coated with a sol-gel organic-inorganic sorbent. Among the benefits of FPSE are its tunable selectivity, adjustable porosity, minimized sample preparation workflow, substantially reduced organic solvent consumption, rapid extraction kinetics and superior extraction efficiency, many of which are well-known criteria for Green Analytical Chemistry. As such, FPSE has established itself as a leading green sample preparation technology of 21st century. In this review, we discuss the principal steps for the development of an FPSE method, the main method optimization strategies, as well as the applications of FPSE in bioanalysis for the extraction of a wide range of analytes (e.g., estrogens, benzodiazepines, androgens and progestogens, penicillins, anti-inflammatory drugs, parabens etc.).

Direct analysis in real time-mass spectrometry for rapid quantification of five anti-arrhythmic drugs in human serum: application to therapeutic drug monitoring

Therapeutic drug monitoring (TDM) is necessary for the optimal administration of anti-arrhythmic drugs in the treatment of heart arrhythmia. The present study aimed to develop and validate a direct analysis in real time tandem mass spectrometry (DART–MS/MS) method for the rapid and simultaneous determination of five anti-arrhythmic drugs (metoprolol, diltiazem, amiodarone, propafenone, and verapamil) and one metabolite (5-hydroxy(OH)-propafenone) in human serum. After the addition of isotope-labeled internal standards and protein precipitation with acetonitrile, anti-arrhythmic drugs were ionized by DART in positive mode followed by multiple reaction monitoring (MRM) detection. The use of DART–MS/MS avoided the need for chromatographic separation and allowed rapid and ultrahigh throughput analysis of anti-arrhythmic drugs in a total run time of 30 s per sample. The DART–MS/MS method yielded satisfactory linearity (R² ≥ 0.9906), accuracy (86.1–109.9%), and precision (≤ 14.3%) with minimal effect of biological matrixes. The method was successfully applied to analyzing 30 clinical TDM samples. The relative error (RE) of the concentrations obtained by DART–MS/MS and liquid chromatography-tandem mass spectrometry (LC–MS/MS) was within ± 13%. This work highlights the potential usefulness of DART for the rapid quantitative analysis of anti-arrhythmic drugs in human serum and gives rapid feedback in the clinical TDM practices.

Rapid identification and determination of pyrrolizidine alkaloids in herbal and food samples via direct analysis in real-time mass spectrometry

Pyrrolizidine alkaloids (PAs) are naturally occurring plant toxins associated with severe liver damage if excessive ingestion. Herein, a novel analytical strategy on utilizing direct analysis in real-time mass spectrometry (DART-MS) was developed, and applied in analysis of six representative PAs. The calibration curves in the range of 10-1000 ng·mL^-1 were established, and relative standard deviations (RSDs) were less than 10%. The limits of detection (LODs) and limits of quantitation (LOQs) were 0.55-0.85 ng·mL^-1 and 1.83-2.82 ng·mL^-1, respectively. The feasibility of method was indicated by analysing real samples including Gynura japonica, drug tablets, granules, and fresh cow's milk. Moreover, the results of DART-MS were in good agreement with those observed by high performance liquid chromatography mass spectrometry (HPLC-MS), but consumed less time without chromatographic separation. This research provides a facile fashion for safety assessment of herbal and food products containing PAs and presents promising applications in food, pharmaceutical and clinical analysis.