Bone response to in vivo mechanical loading in C3H/HeJ mice

Dynamic hydraulic fluid stimulation regulated intramedullary pressure

Physical signals within the bone, i.e. generated from mechanical loading, have the potential to initiate skeletal adaptation. Strong evidence has pointed to bone fluid flow (BFF) as a media between an external load and the bone cells, in which altered velocity and pressure can ultimately initiate the mechanotransduction and the remodeling process within the bone. Load-induced BFF can be altered by factors such as intramedullary pressure (ImP) and/or bone matrix strain, mediating bone adaptation. Previous studies have shown that BFF induced by ImP alone, with minimum bone strain, can initiate bone remodeling. However, identifying induced ImP dynamics and bone strain factor in vivo using a non-invasive method still remains challenging. To apply ImP as a means for alteration of BFF, it was hypothesized that non-invasive dynamic hydraulic stimulation (DHS) can induce local ImP with minimal bone strain to potentially elicit osteogenic adaptive responses via bone-muscle coupling. The goal of this study was to evaluate the immediate effects on local and distant ImP and strain in response to a range of loading frequencies using DHS. Simultaneous femoral and tibial ImP and bone strain values were measured in three 15-month-old female Sprague Dawley rats during DHS loading on the tibia with frequencies of 1Hz to 10Hz. DHS showed noticeable effects on ImP induction in the stimulated tibia in a nonlinear fashion in response to DHS over the range of loading frequencies, where they peaked at 2Hz. DHS at various loading frequencies generated minimal bone strain in the tibiae. Maximal bone strain measured at all loading frequencies was less than 8με. No detectable induction of ImP or bone strain was observed in the femur. This study suggested that oscillatory DHS may regulate the local fluid dynamics with minimal mechanical strain in the bone, which serves critically in bone adaptation. These results clearly implied DHS's potential as an effective, non-invasive intervention for osteopenia and osteoporosis treatments.

Dynamic hydraulic flow stimulation on mitigation of trabecular bone loss in a rat functional disuse model

Bone fluid flow (BFF) has been demonstrated as a critical regulator in mechanotransductive signaling and bone adaptation. Intramedullary pressure (ImP) and matrix strain have been identified as potential generators to regulate BFF. To elevate in vivo oscillatory BFF using ImP, a dynamic hydraulic stimulation (DHS) approach was developed. The objective of this study was to evaluate the effects of DHS on mitigation of bone loss and structural alteration in a rat hindlimb suspension (HLS) functional disuse model. Sixty-one 5-month old female Sprague-Dawley rats were divided into five groups: 1) baseline control, 2) age-matched control, 3) HLS, 4) HLS+static loading, and 5) HLS+DHS. Hydraulic flow stimulation was carried out daily on a "10 min on-5 min off-10 min on" loading regime, 5 days/week, for a total of 4 weeks in the tibial region. The metaphyseal trabecular regions of the proximal tibiae were analyzed using μCT and histomorphometry. Four weeks of HLS resulted in a significant loss of trabecular bone, leading to structural deterioration. HLS with static loading alone was not sufficient to attenuate the bone loss. Bone quantity and microarchitecture were significantly improved by applying DHS loading, resulting increase of 83% in bone volume fraction, 25% in trabecular number and mitigation of 26% in trabecular separation compared to HLS control. Histomorphometry analysis on trabecular mineralization coincided with the μCT analysis, in which DHS loading yielded increases of 34% in histomorphometric BV/TV, 121% in MS/BS, 190% in BFR/BS and 146% in BFR/BV, compared to the HLS control. Overall, the data demonstrated that dynamic hydraulic flow loading has potentials to provide regulatory signals for mitigating bone loss induced by functional disuse. This approach may provide a new alternative mechanical intervention for future clinical treatment for osteoporosis.

Bone cross-sectional geometry in male runners, gymnasts, swimmers and non-athletic controls: a hip-structural analysis study

Loading of the skeleton is important for the development of a functionally and mechanically appropriate bone structure, and can be achieved through impact exercise. Proximal femur cross-sectional geometry was assessed in the male athletes (n = 55) representing gymnastics, endurance running and swimming, and non-athletic controls (n = 22). Dual energy X-ray absorptiometry (iDXA, GE Healthcare, UK) measurements of the total body (for body composition) and the left proximal femur were obtained. Advanced hip structural analysis (AHA) was utilised to determine the areal bone mineral density (aBMD), hip axis length (HAL), cross-sectional area (CSA), cross-sectional moment of inertia (CSMI) and the femoral strength index (FSI). Gymnasts and runners had greater age, height and weight adjusted aBMD than in swimmers and controls (p < 0.05). Gymnasts and runners had greater resistance to axial loads (CSA) and the runners had increased resistance against bending forces (CSMI) compared to swimmers and controls (p < 0.01). Controls had a lower FSI compared to gymnasts and runners (1.4 vs. 1.8 and 2.1, respectively, p < 0.005). Lean mass correlated with aBMD, CSA and FSI (r = 0.365-0.457, p < 0.01), particularly in controls (r = 0.657-0.759, p < 0.005). Skeletal loading through the gymnastics and running appears to confer a superior bone geometrical advantage in the young adult men. The importance of lean body mass appears to be of particular significance for non-athletes. Further characterisation of the bone structural advantages associated with different sports would be of value to inform the strategies directed at maximising bone strength and thus, preventing fracture.

Alternative splicing in bone following mechanical loading

It is estimated that more than 90% of human genes express multiple mRNA transcripts due to alternative splicing. Consequently, the proteins produced by different splice variants will likely have different functions and expression levels. Several genes with splice variants are known in bone, with functions that affect osteoblast function and bone formation. The primary goal of this study was to evaluate the extent of alternative splicing in a bone subjected to mechanical loading and subsequent bone formation. We used the rat forelimb loading model, in which the right forelimb was loaded axially for 3 min, while the left forearm served as a non-loaded control. Animals were subjected to loading sessions every day, with 24 h between sessions. Ulnae were sampled at 11 time points, from 4 h to 32days after beginning loading. RNA was isolated and mRNA abundance was measured at each time point using Affymetrix exon arrays (GeneChip® Rat Exon 1.0 ST Arrays). An ANOVA model was used to identify potential alternatively spliced genes across the time course, and five alternatively spliced genes were validated with qPCR: Akap12, Fn1, Pcolce, Sfrp4, and Tpm1. The number of alternatively spliced genes varied with time, ranging from a low of 68 at 12h to a high of 992 at 16d. We identified genes across the time course that encoded proteins with known functions in bone formation, including collagens, matrix proteins, and components of the Wnt/β-catenin and TGF-β signaling pathways. We also identified alternatively spliced genes encoding cytokines, ion channels, muscle-related genes, and solute carriers that do not have a known function in bone formation and represent potentially novel findings. In addition, a functional characterization was performed to categorize the global functions of the alternatively spliced genes in our data set. In conclusion, mechanical loading induces alternative splicing in bone, which may play an important role in the response of bone to mechanical loading.

Leptin receptor (Lepr) is a negative modulator of bone mechanosensitivity and genetic variations in Lepr may contribute to the differential osteogenic response to mechanical stimulation in the C57BL/6J and C3H/HeJ pair of mouse strains

This study investigated the role of leptin receptor (Lepr) signaling in determining the bone mechanosensitivity and also evaluated whether differences in the Lepr signaling may contribute to the differential osteogenic response of the C57BL/6J (B6) and C3H/HeJ (C3H) pair of mouse strains to mechanical stimuli. This study shows that a loading strain of ∼2,500 με, which was insufficient to produce a bone formation response in B6 mice, significantly increased bone formation parameters in leptin-deficient ob(-)/ob(-) mice and that a loading strain of ∼3,000 με also yielded greater osteogenic responses in Lepr-deficient db(-)/db(-) mice than in wild-type littermates. In vitro, a 30-min steady shear stress increased [(3)H]thymidine incorporation and Erk1/2 phosphorylation in ob(-)/ob(-) osteoblasts and db(-)/db(-) osteoblasts much greater than those in corresponding wild-type osteoblasts. The siRNA-mediated suppression of Lepr expression in B6 osteoblasts enhanced (but in osteoblasts of C3H (the mouse strain with poor bone mechanosensitivity) restored) their anabolic responses to shear stress. The Lepr signaling (leptin-induced Jak2/Stat3 phosphorylation) in C3H osteoblasts was higher than that in B6 osteoblasts. One of the three single nucleotide polymorphisms in the C3H Lepr coding region yielded an I359V substitution near the leptin binding region, suggesting that genetic variation of Lepr may contribute to a dysfunctional Lepr signaling in C3H osteoblasts. In conclusion, Lepr signaling is a negative modulator of bone mechanosensitivity. Genetic variations in Lepr, which result in a dysfunctional Lepr signaling in C3H mice, may contribute to the poor osteogenic response to loading in C3H mice.

Bone modeling response to voluntary exercise in the hindlimb of mice

The functional adaptation of juvenile mammalian limb bone to mechanical loading is necessary to maintain bone strength. Diaphyseal size and shape are modified during growth through the process of bone modeling. Although bone modeling is a well-documented response to increased mechanical stress on growing diaphyseal bone, the effect of proximodistal location on bone modeling remains unclear. Distal limb elements in cursorial mammals are longer and thinner, most likely to conserve energy during locomotion because they require less energy to move. Therefore, distal elements are hypothesized to experience greater mechanical loading during locomotion and may be expected to exhibit a greater modeling response to exercise. In this study, histomorphometric comparisons are made between femora and tibiae of mice treated with voluntary exercise and a control group (N = 20). We find that femora of exercised mice exhibit both greater bone growth rates and growth areas than do controls (P < 0.05). The femora of exercised mice also have significantly greater cortical area, bending rigidity, and torsional rigidity (P < 0.05), although bending and torsional rigidity are comparable when standardized by bone length. Histomorphometric and cross-section geometric properties of the tibial midshaft of exercised and control mice did not differ significantly, although tibial length was significantly greater in exercised mice (P < 0.05). Femora of exercised mice were able to adapt to increased mechanical loading through increases in compressive, bending, and torsional rigidity. No such adaptations were found in the tibia. It is unclear if this is a biomechanical adaptation to greater stress in proximal elements or if distal elements are ontogenetically constrained in a tradeoff of bone strength of distal elements for bioenergetic efficiency during locomotion.

32 wk old C3H/HeJ mice actively respond to mechanical loading

Numerous studies indicate that C3H/HeJ (C3H) mice are mildly responsive to mechanical loading compared to C57BL/6J (C57) mice. Guided by data indicating high baseline periosteal osteoblast activity in 16 wk C3H mice, we speculated that simply allowing the C3H mice to age until basal periosteal bone formation was equivalent to that of 16 wk C57 mice would restore mechanoresponsiveness in C3H mice. We tested this hypothesis by subjecting the right tibiae of 32 wk old C3H mice and 16 wk old C57 mice to low magnitude rest-inserted loading (peak strain: 1235 mu epsilon) and then exposing the right tibiae of 32 wk C3H mice to low (1085 mu epsilon) or moderate (1875 mu epsilon) magnitude cyclic loading. The osteoblastic response to loading on the endocortical and periosteal surfaces was evaluated via dynamic histomorphometry. At 32 wk of age, C3H mice responded to low magnitude rest-inserted loading with significantly elevated periosteal mineralizing surface, mineral apposition rate and bone formation compared to unloaded contralateral bones. Surprisingly, the periosteal bone formation induced by low magnitude rest-inserted loading in C3H mice exceeded that induced in 16 wk C57 mice. At 32 wk of age, C3H mice also demonstrated an elevated response to increased magnitudes of cyclic loading. We conclude that a high level of basal osteoblast function in 16 wk C3H mice appears to overwhelm the ability of the tissue to respond to an otherwise anabolic mechanical loading stimulus. However, when basal surface osteoblast activity is equivalent to that of 16 wk C57 mice, C3H mice demonstrate a clear ability to respond to either rest-inserted or cyclic loading.

Frequency-dependent enhancement of bone formation in murine tibiae and femora with knee loading

Knee loading is a relatively new loading modality in which dynamic loads are laterally applied to the knee to induce bone formation in the tibia and the femur. The specific aim of the current study was to evaluate the effects of loading frequencies (in Hz) on bone formation at the site away from the loading site on the knee. The left knee of C57/BL/6 mice was loaded with 0.5 N force at 5, 10, or 15 Hz for 3 min/day for 3 consecutive days, and bone histomorphometry was conducted at the site 75% away from the loading site along the length of tibiae and femora. The results revealed frequency-dependent induction of bone formation, in which the dependence was different in the tibia and the femur. Compared with the sham-loading control, for instance, the cross-sectional cortical area was elevated maximally at 5 Hz in the tibia, whereas the most significant increase was observed at 15 Hz in the femur. Furthermore, mineralizing surface, mineral apposition rate, and bone formation rate were the highest at 5 Hz in the tibia (2.0-, 1.4-, and 2.7 fold, respectively) and 15 Hz in the femur (1.5-, 1.2-, and 1.8 fold, respectively). We observed that the tibia had a lower bone mineral density with more porous microstructures than the femur. Those differences may contribute to the observed differential dependence on loading frequencies.

Identification of genetic loci that regulate bone adaptive response to mechanical loading in C57BL/6J and C3H/HeJ mice intercross

Strain-dependent differences in bone adaptive responses to loading among inbred mouse strains suggest that genetic background contributes significantly to adaptation to exercise. To explore the genetic regulation of response to loading, we performed a genome-wide search for linkage in a cross between two strains, a good responder, C57BL6/J (B6), and a poor responder, C3H/HeJ (C3H). Using a four-point bending model, the right tibia was loaded by applying 9 N force for 36 cycles for 12 days in 10-week-old female B6xC3H F2 mice. Changes in bone density (BMD) and bone size were evaluated in vivo by pQCT. Measurements from non-loaded left tibia were used as an internal control to calculate loading-induced percent increase in BMD and bone size, thus excluding the possibility of identifying background QTL(s) due to natural allelic variation in mapping strains. A genome-wide scan was performed using 111 microsatellite markers in DNA samples collected from 329 F2 mice. Heritability of bone adaptive response to loading was between 70 and 80%. The mean increase, expressed as percent of unloaded tibia, was 5% for BMD, 9% for periosteal circumference (PC), and 14% for cortical thickness in F2 mice (n = 329). All these phenotypes showed normal distributions. Absence of significant correlation between BMD response to four-point bending and body weight or bone size suggested that the bone adaptive response was independent of bone size. Interval mapping revealed that BMD response to four-point bending was influenced by three significant loci on Chrs 1 (log-of-odds ratio score (LOD) 3.4, 91.8 cM), 3 (LOD 3.6, 50.3 cM), and 8 (LOD 4.2, 60.1 cM) and one suggestive QTL on Chr 9 (LOD 2.5, 33.9 cM). Loading-induced increases in PC and Cth were influenced by four significant loci on Chrs 8 (LOD 3.0, 68.9 cM), 9 (LOD 3.0, 13.1 cM), 17 (LOD 3.0, 39.3 cM), and 18 (LOD 3.0, 0 cM) and two suggestive loci on Chr 9 (LOD 2.2, 24 cM) and 11 (LOD 2.1, 69.9 cM). Pairwise analysis showed the presence of several significant and suggestive interactions between loci on Chrs 1, 3, 8, and 13 for BMD trait. This is the first study that provides evidence for the presence of multiple genetic loci regulating bone anabolic responses to loading in the B6xC3H intercross. Knowledge of the genes underlying these loci could provide novel approaches to improve skeletal mass.

Cancellous bone adaptation to in vivo loading in a rabbit model

Biophysical stimuli are important to the development and maintenance of cancellous bone, but the regulatory mechanisms need to be understood. We investigated the effects of mechanical loading applied in vivo to native cancellous bone in the rabbit on bone formation and trabecular realignment. A novel device was developed to apply controlled compressive loads to cancellous bone in situ. The effect of loading on cancellous bone volume fraction and architecture was quantified. A 4-week experiment was performed in rabbits with devices implanted bilaterally. Cyclic 1 MPa pressures were applied daily to the right limb for 10, 25, or 50 cycles at 0.5 Hz, and the left limb served as the control without any applied loading. Microcomputed tomography and histomorphometry were used to characterize the cancellous tissue within a 4-mm spherical volume located below the loading core. In vivo cyclic loading significantly increased the bone volume fraction, direct trabecular thickness, mean intercept length, and mineral apposition rate in the loaded limbs compared with contralateral limbs. Insufficient evidence was found to demonstrate an effect of number of cycles on the cancellous adaptation between loaded and control limbs. Using a rabbit model, we demonstrated that mechanical loading applied to cancellous bone in situ increased bone formation and altered trabecular morphology. This in vivo model will allow further investigation of cancellous functional adaptation to controlled mechanical stimuli and the influence of mechanical loading parameters, metabolic status, and therapeutic agents.

Global gene expression analysis in the bones reveals involvement of several novel genes and pathways in mediating an anabolic response of mechanical loading in mice

To identify the genes and signal pathways responsible for mechanical loading-induced bone formation, we evaluated differential gene expression on a global basis in the tibias of C57BL/6J (B6) mice after four days of four-point bending. We applied mechanical loads to the right tibias of the B6 mice at 9 N, 2 Hz for 36 cycles per day, with the left tibias used as unloaded controls. RNA from the tibias was harvested 24 h after last stimulation and subjected to microarray. Of the 20,280 transcripts hybridized to the array, 346 were differentially expressed in the loaded bones compared to the controls. The validity of the microarray data was established with the increased expression of bone-related genes such as pleiotrophin, osteoglycin, and legumain upon four-point bending and confirmation of increased expression of selected genes by real-time PCR. The list of differentially expressed genes includes genes involved in cell growth, differentiation, adhesion, proteolysis, as well as signaling molecules of receptors for growth factors, integrin, Ephrin B2, endothelin, and adhesion G protein coupled receptor. Pathway analyses suggested that 28 out of the 346 genes exhibited a direct biological association. Among the biological network, fibronectin and pleitrophin function as important signaling molecules in regulating periosteal bone formation and resorption in response to four-point bending. Furthermore, some expressed sequence tags (ESTs) with no prior known function have been identified as potential mediators of mechanotransduction signaling pathways. Further studies on these previously unknown genes will improve our understanding of the molecular pathways and mechanisms involved in bone's response to mechanical stress.

Diaphyseal bone formation in murine tibiae in response to knee loading

Mechanical stimulation is critical for bone architecture and bone mass. The aim of this study was to examine the effects of mechanical loads applied to the knee. The specific question was whether loads applied to the tibial epiphysis would enhance bone formation in the tibial diaphysis. In C57/BL/6 mice, loads of 0.5 N were applied for 3 min per day for 3 days at 5, 10, or 15 Hz. Bone samples were harvested 13 days after the last loading. The strains were measured 13 +/- 2 microstrains at 5 Hz in the diaphysis. The histomorphometric data in the diaphysis clearly showed enhanced bone formation. First, compared with nonloaded control the cross-sectional cortical area was increased by 11% at 5 Hz and 8% at 10 Hz (both P < 0.05). Second, the cortical thickness was elevated by 12% at 5 Hz (P < 0.01) and 8% at 10 Hz (P < 0.05). Third, mineralizing surface (MS/BS), mineral apposition rate (MAR), and bone formation rate (BFR/BS) were increased at 5 Hz (P < 0.01 for MS/BS; P < 0.001 for MAR and BFR/BS) and at 10 Hz (P < 0.05 for MS/BS; P < 0.01 for MAR and BFR/BS). Bone formation was enhanced more extensively in the medial side than the lateral or the posterior side. The results reveal that knee loading is an effective means to enhance bone formation in the tibial diaphysis in a loading-frequency dependent manner without inducing significant in situ strain at the site of bone formation.

Osteoblast responses one hour after load-induced fluid flow in a three-dimensional porous matrix

When bone is loaded, substrate strain is generated by the external force and this strain induces fluid flow that creates fluid shear stress on bone cells. Our current understanding of load-driven gene regulation of osteoblasts is based primarily on in vitro studies on planer two-dimensional tissue culture substrates. However, differences between a flat layer of cells and cells in 3-dimensional (3D) ECM are being recognized for signal transduction. Proliferation and differentiation of osteoblasts are affected by substrate geometry. Here we developed a novel 3D culture system that would mimic physiologically relevant substrate strain as well as strain-induced fluid flow in a 3D porous collagen matrix. The system allowed us to evaluate the responses of osteoblasts in a 3D stress-strain environment similar to a mechanical field to which bone is exposed. Using MC3T3-E1 osteoblasts grown in the 3D collagen matrix with and without hydroxyapatite deposition, we tested the role of strain and the strain-induced fluid flow in the expression of the load-responsive genes such as c-fos, egr1, cox2, osteopontin, and mmp1B involved in transcriptional regulation, osteogenesis, and rearrangement of ECM. Strain-induced fluid flow was visualized with a microspheres approximately 3 microm in diameter in real time, and three viscoelastic parameters were determined. The results obtained by semi-quantitative PCR, immunoblot assay, enzymatic activity assays for collagenase and gelatinase, and mechanical characterization of collagen matrices supported the dominant role of strain-induced fluid flow in expression of the selected genes one hour after the mechanical treatment.

Bone intrinsic material properties in three inbred mouse strains

This study assessed genetically based differences in intrinsic material properties of both cortical and cancellous bone in adult females of three inbred mouse strains [C57BL/6J (B6), DBA/2J (D2), C3H/HeJ (C3)]. These mouse strains have previously been shown to differ in bone mineral content (BMC) and density (BMD). Distal femoral cancellous bone and midshaft cortical bone in femurs and tibias were assessed for intrinsic material properties using nanoindentation technique. The intrinsic material properties tested were modulus (E(b)) and hardness (H) of the midshaft femoral and tibial cortical bone cross sections and of cancellous bone in the distal femur. Both femoral and tibial cortical bone intrinsic material properties were different among the three inbred mouse strains. Femoral modulus and tibial hardness in cortical bone and hardness in cancellous bone were either greatest or showed greater trends in C3 mice as compared to both D2 and B6. Cancellous bone modulus was similar among the three mouse strains. With the exception of the D2 mice, the femoral and tibial cortical modulus were similar within each mouse strain. The tibial cortical modulus was smaller than the femoral cortical modulus for D2 mouse strain. The cortical hardness was greater in tibiae compared with that in femora within each mouse strain. The nanoindentation data suggest that cortical and cancellous intrinsic material properties are influenced by the genetic background of the inbred mouse strains. The inbred mouse strain-related intrinsic material property phenotype can be used to locate responsible quantitative trait loci (QTLs) in future studies of recombinant inbred mouse strains.

Evidence for a skeletal mechanosensitivity gene on mouse chromosome 4

Differences in skeletal mechanical adaptation between C3H/HeJ (C3H) and C57BL/6J (B6) mouse strains suggest that these mice can be used to elucidate the genes involved in mechanosensitivity regulation. The C3H and B6 skeletons also differ in bone size, and several quantitative trait loci (QTL) have been mapped for bone size. We hypothesized that genes controlling bone size (external diameter) might exert their effect by influencing mechanosensitivity. The hypothesis was tested by applying mechanical loads to the ulnae of the B6.C3H-4T (4T) congenic mouse strain, which is genetically 98.4% B6 and carries the C3H chromosome 4 (Chr. 4) QTL genomic DNA. Mechanical strain was measured at the midshaft ulna in separate calibration animals. 4T mice were significantly more responsive to mechanical stimulation than B6 control mice, as assessed by changes in bone geometry and fluorochrome-derived bone formation rates. Bone formation rates were also greater in the ulnae and femora of 6-wk-old 4T mice engaged in normal cage activity compared with age-matched B6 mice. Collectively, the results might explain why 4T mice have wider femora and ulnae than do B6 control mice and suggest that mouse Chr. 4 contains a genetic locus that modulates the mechanosensitivity of bone tissue.

Mechanotransduction in bone: genetic effects on mechanosensitivity in mice

Bone formation is enhanced by mechanical loading, but human exercise intervention studies have shown that the response to mechanical loading is variable, with some individuals exhibiting robust osteogenic responses while others respond modestly. Thus, mechanosensitivity - the ability of bone tissue to detect mechanical loads - could be under genetic control. We applied controlled mechanical loading to the ulnae of 20-week-old (adult) female mice derived from three different inbred strains (C3H/He, C57BL/6, and DBA/2), and measured the bone formation response with fluorochrome labels. Mechanical properties, including mechanical strain, second moments of area, and cortical bone material properties, were measured in a group of calibration animals not subjected to in vivo loading. The C3H/He mice were significantly less responsive to mechanical loading than the other two biological strains. Material properties (flexural elastic modulus, ultimate stress) were greatest in the C3H/He cortical tissue. Geometric and areal properties at the midshaft ulna were also greatest in the C3H/He mice. Based on the presumed role of osteocytes in strain detection, we measured osteocyte lacuna population densities in decalcified midshaft ulna sections. Osteocyte lacuna density was not related to mechanosensitivity. Our data suggest that bone mechanosensitivity has a significant genetic component. Identification of the genes that exert their influence on mechanosensitivity could ultimately lead to therapies that enhance bone mass and reduce fracture susceptibility.

Validation of a technique for studying functional adaptation of the mouse ulna in response to mechanical loading

Functional adaptation of the mouse ulna in response to artificial loading in vivo was assessed using a technique previously developed in the rat. Strain gauge recordings from the mouse ulnar midshaft during locomotion showed peak strains of 1680 muepsilon and maximum strain rates of 0.03 sec(-1). During falls from 20 cm these reached 2620 muepsilon and 0.10 sec(-1). Axial loads of 3.0 N and 4.3 N, applied through the olecranon and flexed carpus, engendered peak strains at the lateral ulnar midshaft of 2000 muepsilon and 3000 muepsilon, respectively. The left ulnae of 17, 17-week-old female CD1 mice were loaded for 10 min with a 4 Hz trapezoidal wave engendering a strain rate of 0.1 sec(-1) for 5 days/week for 2 weeks. The mice were killed 3 days later. The response of the cortical bone of the diaphysis was assessed histomorphometrically using double calcein labels administered on days 3 and 12 of the loading period. Loading to peak strains of 2000 muepsilon stimulated lamellar periosteal bone formation, but no response endosteally. The greatest increase in cortical bone area was 4 mm distal to the midshaft (5 +/- 0.4% compared with 0.1 +/- 0.1% in controls [p < 0.01]). Periosteal bone formation rate (BFR) at this site was 0.73 +/- 0.06 microm(2)/microm per day, compared with 0.03 +/- 0.02 microm(2)/microm per day in controls (p < 0.01). Loading to peak strains of 3000 muepsilon induced a mixed woven/lamellar periosteal response and lamellar endosteal bone formation. Both of these were greatest 3-4 mm distal to the ulnar midshaft. At this level, the loading-induced periosteal response increased cortical bone area by 21 +/- 4% compared with 0.03 +/- 0.02% in controls, and resulted in a BFR of 2.84 +/- 0.42 microm(2)/microm per day, compared with 0.01 +/- 0.01 microm(2)/microm per day in controls (p < 0.05). Endosteal new bone formation resulted in a 2 +/- 0.4% increase in cortical bone area, compared with 0.4 +/- 0.3% in controls, and a BFR of 1.05 +/- 0.23 microm(2)/microm per day, compared with 0.22 +/- 0.15 microm(2)/microm per day in controls (p < 0.05). These data show that the axial ulna loading technique developed in the rat can be used successfully in the mouse. As in the rat, a short daily period of loading results in an osteogenic response related to peak strain magnitude. One important advantage in using mice over rats involves the potential for assessing the effects of loading in transgenics.

Why mechanobiology? A survey article

The central paradigm of skeletal mechanobiology is that mechanical forces modulate morphological and structural fitness of the skeletal tissues-bone, cartilage, ligament and tendon. Traditionally, skeletal biomechanics has focussed on how these tissues perform the structural and locomotory functions of the vertebrate skeleton. In mechanobiology the central question is how these same load-bearing tissues are produced, maintained and adapted by cells as an active response to biophysical stimuli in their environment. The idea that 'form follows function' is not new, but we now believe that the scientific community has the knowledge and tools to prove, understand and use functional adaptation to benefit medicine and human health. In this Survey Article the philosophy and progress of skeletal mechanobiology are discussed. The revival of this science, with roots dating back to the 19th Century, is now driven by new developments in cellular, molecular and computational technologies. These developments are still in an early stage of application, but if modern mechanobiology fulfills the promises of its ambitions, the results will bring great benefits to tissue engineering and to the treatment and prevention of skeletal conditions such as congenital deformities, osteoporosis, osteoarthritis and bone fractures.

Noninvasive loading of the murine tibia: an in vivo model for the study of mechanotransduction

Transgenic and knockout mice present a unique opportunity to study mechanotransduction pathways in vivo, but the difficulty inherent with applying externally controlled loads to the small mouse skeleton has hampered this approach. We have developed a novel device that enables the noninvasive application of controlled mechanical loads to the murine tibia. Calibration of tissue strains induced by the device indicated that the normal strain environment was repeatable across loading bouts. Two in vivo studies were performed to show the usefulness of the device. Using C57Bl/6J mice, we found that dynamic but not static loading increased cortical bone area. This result is consistent with previous models of bone adaptation, and the lack of adaptation induced by static loading serves as a negative control for the device. In a preliminary study, transgenic mice selectively overexpressing insulin-like growth factor 1 (IGF-1) in osteoblasts underwent a low-magnitude loading regimen. Periosteal bone formation was elevated 5-fold in the IGF-1-overexpressing mice but was not elevated in wild-type littermates, showing the potential for synergism between mechanical loading and selected factors. Based on these data, we anticipate that the murine tibia-loading device will enhance assessment of mechanotransduction pathways in vivo and, as a result, has the potential to facilitate novel gene discovery and optimization of synergies between drug therapies and mechanical loading.

Bone adaptation response to sham and bending stimuli in mice

This study presents inbred-strain-related differences in tibial bone adaptation response to low-force loading in four-point bending and sham (pad pressure) arrangements in mice. Our previous work in mice has shown that at relatively high but equal bending forces (9 N or a bending moment of 16.88 N-mm), C57BL/6J mice respond with significantly greater bone formation than C3H/HeJ mice. Because of high tibial strains, the majority of the bone response in our previous study was woven bone. In this, study, we reduced the loading forces to 5 N or a bending moment of 9.38 N-mm (to decrease the woven-bone formation response) and investigated inbred-strain-related bone adaptation differences resulting from bending and sham loading (reported here for the first time in C57BL/6J) in these mice. Twenty-four female mice within each inbred mouse strain (C3H/HeJ [C3H] and C57BL/6J [B6]) were randomly divided into the two loading groups (12 per group sham and bending, total of 48 mice). All of the external loading was done for 36 cycles at 2 Hz, 3 d/wk for 3 wk. The bone adaptation response at lower forces exhibited a pattern similar to that seen for the higher forces in the previous study, suggesting that the patterns of bone adaptation were inbred strain related and independent of bending force magnitude. The bending-related periosteal mineral apposition surface (pMS) and mineral apposition rate (MAR) were respectively 40% and 45% greater in B6 than in C3H. The cortical bone adaptation response to bending was greater when compared to sham or pad pressure for each inbred strain of mice, suggesting that the majority of the bone adaptation response was the result of bending stimulus and not local pressure from pad contact. In addition, regardless of loading arrangement (sham or bending), the bone adaptation response in C57BL/6J mice was greater than C3H/HeJ.

High femoral bone mineral content and density in male football (soccer) players

PURPOSE

This investigation examined the effect that long-term football (soccer) participation may have on areal bone mineral density (BMD) and bone mineral content (BMC) in male football players.

METHODS

Dual energy x-ray absorptiometry (DXA) scans were obtained in 33 recreational male football players active in football for the last 12 yr and 19 nonactive subjects from the same population. Both groups had comparable age (23 +/- 4 yr vs 24 +/- 3 yr), body mass (73 +/- 7 kg vs 72 +/- 11 kg), height (176 +/- 5 cm vs 176 +/- 8 cm), and calcium intake (23 +/- 10 mg.kg(-1).d(-1) vs 20 +/- 11 mg.kg(-1).d(-1) (mean +/- SD).

RESULTS

The football players showed 8% greater total lean mass (P < 0.001), 13% greater whole-body BMC (P < 0.001), and 5 units lower percentage body fat (P < 0.001) than control subjects. Lumbar spine (L2-L4) BMC and BMD were 13% and 10% higher, respectively, in the football players than in the control subjects (P < 0.05). Furthermore, football players displayed higher femoral neck BMC (24%, 18%, 23%, and 24% for the femoral neck, intertrochanteric, greater trochanter, and Ward's triangle subregions, respectively, P < 0.05) and BMD (21%, 19%, 21%, and 27%, respectively, P < 0.05) than controls. BMC in the whole leg was 16-17% greater in the football players, mainly because of enhanced BMD (9-10%) but also because of bone hypertrophy, since the area occupied by the osseous pixels was 7% higher (867 +/- 63 cm2 vs 814 +/- 26 cm2, P < 0.05). Leg muscle mass was 11% higher in the football players than in the control subjects (20,635 +/- 2,073 g vs 18,331 +/- 2,301 g, P < 0.001). No differences were found between the legs in either groups for BMC, BMD, and muscle mass. Left leg muscle mass was correlated with femoral neck BMC and BMD (P < 0.001), as well as with lumbar spine (L2-L4) BMC and BMD (P < 0.001).

CONCLUSION

Long-term football participation, starting at prepubertal age, is associated with markedly increased BMC and BMD at the femoral neck and lumbar spine regions.