Changes in microbial community in the presence of oil and chemical dispersant and their effects on the corrosion of API 5L steel coupons in a marine-simulated microcosm

Microbial community structure and co-occurrence network stability in seawater and microplastic biofilms under prometryn pollution in marine ecosystems

Prometryn has been extensively detected in marine environment because of its widespread usage in agriculture and aquaculture and has been concerns since its serious effects on aquatic organisms. However, its impact on the microbial community in the marine ecosystem including seawater and biofilm is still unclear. Therefore, a short-term indoor microcosm experiment of prometryn exposure was conducted. This study found that prometryn had a more significant impact on the structure and stability of the microbial community in seawater compared to microplastic biofilms. Additionally, we observed that the assembly of the microbial community in biofilms was more affected by stochastic processes than in seawater under the exposure of prometryn. Our study provided evidence for the increasing impact of the microbial communities under the stress of prometryn and microplastics.

Treatment of high-strength saline bilge wastewater by four pilot-scale aerobic moving bed biofilm reactors and comparison of the microbial communities

Four Pilot-scale Moving Bed Biofilm Reactors (MBBRs) were operated for the treatment of real, saline, bilge wastewater. The MBBRs were connected in pairs to create two system configurations with different filling ratios (20%, 40%) and were operated in parallel. The inflow organic loading rate (OLR) varied from 3.6 ± 0.2 to 7.8 ± 0.6 g COD L-1 d-1, salinity was >15 ppt and three hydraulic residence times (HRTs) were tested 48, 30 and 24 h. In both systems, the first-stage bioreactors (R1 and R3) eliminated the higher part of the organic load (57%-65%). The second-stage bioreactors (R2 and R4) removed an additional fraction (18%-31%) of the organic load received by the effluent of R1 and R3, respectively. The microbial communities of the influent wastewater, suspended, and attached biomass were determined using 16S rRNA gene amplicon sequencing analysis. The evolution of the microbial communities was investigated and compared over the different operational phases. The microbial communities of the biofilm presented higher diversity and greater stability in composition over time, while the suspended biomass exhibited intense and rapid changes in the dominance of genera. Proteobacteria, Bacteroidetes and Firmicutes were highly present in the biofilm. The genera Celeribacter, Novispirillum, Roseovarius (class: Alphaproteobacteria) and Formosa (class: Flavobacteriia) were highly present during all operational phases. Principal Component Analysis (PCA) was used to identify similarities between samples, exhibiting high relation of samples according to the series of the bioreactor (1st, 2nd).

Shumkonia mesophila gen. nov., sp. nov., a novel representative of Shumkoniaceae fam. nov. and its potentials for extracellular polymeric substances formation and sulfur metabolism revealed by genomic analysis

A microaerophilic, mesophilic, chemoorganoheterotrophic bacterium, designated Y-P2T, was isolated from oil sludge enrichment in China. Cells of the strain were Gram-stain-negative, non-motile, non-spore-forming, rod-shaped or slightly curved with 0.8-3.0 µm in length and 0.4-0.6 µm in diameter. The strain Y-P2T grew optimally at 25 °C (range from 15 to 30 °C) and pH 7.0 (range from pH 6.0 to 7.5) without NaCl. The major cellular fatty acids were C16:0, summed feature 3 (C16:1 ω7c and/or C16:1 ω6c), summed feature 8 (C18:1 ω7c and/or C18:1 ω6c). The main polar liquids of strain Y-P2T comprised phosphatidylethanolamine (PE) and phosphatidylglycerol (PG). The respiratory quinone was Q-10. Acetate and H2 were the fermentation products of glucose. The DNA G + C content was 66.0%. Strain Y-P2T shared the highest 16S rRNA gene sequence similarity (90.3-90.6%) with species within Oceanibaculum of family Thalassobaculaceae in Rhodospirillales. Phylogenetic analyses based on 16S rRNA gene sequences and genomes showed that strain Y-P2T formed a distinct evolutionary lineage within the order Rhodospirillales. On the basis of phenotypic, phylogenetic and phylogenomic data, we propose that strain Y-P2T represents a novel species in a novel genus, for which Shumkonia mesophila gen. nov., sp. nov., within a new family Shumkoniaceae fam. nov. The type strain is Y-P2T (= CCAM 826 T = JCM 34766 T).

Exploring the bioremediation capability of petroleum-contaminated soils for enhanced environmental sustainability and minimization of ecotoxicological concerns

The bioremediation of soils contaminated with petroleum hydrocarbons (PHCs) has emerged as a promising approach, with its effectiveness contingent upon various types of PHCs, i.e., crude oil, diesel, gasoline, and other petroleum products. Strategies like genetically modified microorganisms, nanotechnology, and bioaugmentation hold potential for enhancing remediation of polycyclic aromatic hydrocarbon (PAH) contamination. The effectiveness of bioremediation relies on factors such as metabolite toxicity, microbial competition, and environmental conditions. Aerobic degradation involves enzymatic oxidative reactions, while bacterial anaerobic degradation employs reductive reactions with alternative electron acceptors. Algae employ monooxygenase and dioxygenase enzymes, breaking down PAHs through biodegradation and bioaccumulation, yielding hydroxylated and dihydroxylated intermediates. Fungi contribute via mycoremediation, using co-metabolism and monooxygenase enzymes to produce CO2 and oxidized products. Ligninolytic fungi transform PAHs into water-soluble compounds, while non-ligninolytic fungi oxidize PAHs into arene oxides and phenols. Certain fungi produce biosurfactants enhancing degradation of less soluble, high molecular-weight PAHs. Successful bioremediation offers sustainable solutions to mitigate petroleum spills and environmental impacts. Monitoring and assessing strategy effectiveness are vital for optimizing biodegradation in petroleum-contaminated soils. This review presents insights and challenges in bioremediation, focusing on arable land safety and ecotoxicological concerns.

Arsenic resistance and horizontal gene transfer are associated with carbon and nitrogen enrichment in bacteria

Coastal waters are confluences receiving large amounts of point and non-point sources of pollution. An attempt was made to explore microbial community interactions in response to carbon, nitrogen and metal pollution. Additionally, experiments were designed to analyze the influence of these factors on horizontal gene transfer (HGT). Shift in bacterial diversity dynamics by arsenic stress and nutrient addition in coastal waters was explored by metagenomics of microcosm setups. Phylogenetic analysis revealed equal distribution of Gammaproteobacteria (29%) and Betaproteobacteria (28%) in control microcosm. This proportional diversity from control switched to unique distribution of Gammaproteobacteria (44.5%)> Flavobacteria (17.7%)> Bacteriodia (11.92%)> Betaproteobacteria (11.52%) in microcosm supplemented with carbon, nitrogen and metal (C + N + M). Among metal-stressed systems, alpha diversity analysis indicated highest diversity of genera in C + N + M followed by N + M > C+M> metal alone. Arsenic and ampicillin sensitive E. coli XL1 blue and environmental strains (Vibrio tubiashii W85 and E. coli W101) were tested for efficiency of uptake of plasmid (P) pUCminusMCS (arsB^Ramp^R) under varying stress conditions. Transformation experiments revealed that combined effect of carbon, nitrogen and metal on horizontal gene transfer (HGT) was significantly higher (p < 0.01) than individual factors. The effect of carbon on HGT was proved to be superior to nitrogen under metal stressed conditions. Presence of arsenic in experimental setups (P + M, P + N + M and P + C + M) enhanced the HGT compared to non-metal counterparts supplemented with carbon or nitrogen. Arsenic resistant bacterial isolates (n = 200) were tested for the ability to utilize various carbon and nitrogen substrates and distinct positive correlation (p < 0.001) was found between arsenic resistance and utilization of urea and nitrate. However, evident positive correlation was not found between carbon sources and arsenic resistance. Our findings suggest that carbon and nitrogen pollution in aquatic habitats under arsenic stress determine the microbial community dynamics and critically influence uptake of genetic material from the surrounding environment.

Dynamic changes in the microbial community in the surface seawater of Jiaozhou Bay after crude oil spills: An in situ microcosm study

The changes in the composition and structure of microbial communities in Jiaozhou Bay are strongly affected by marine oil pollution, but the outcomes of the microbial responses and effects of dispersant application remain unclear. Herein, we performed an in situ microcosm study to investigate the response of the indigenous microbial community under crude oil alone and combined oil and dispersant treatment in the surface seawater of a semi-enclosed marine area of Jiaozhou Bay. The dynamics of the bacterial classification based on 16s rDNA sequencing were used to assess the changes with the crude oil concentration, dispersant use, and time. The crude oil resulted in a high abundance of the genera Pseudohongiella, Cycloclasticus, Marivita, and C1-B045 from the Gammaproteobacteria and Alphaproteobacteria classes, suggesting for hydrocarbon degradation. However, the dispersant treatment was more advantageous for Pacificibacter, Marivita, and Loktanella. Besides accelerating the rate of bacterial community succession, the dispersants had significantly stronger effects on the structure of the bacterial community and the degradation functions than the oil. A higher dose of oil exposure corresponded to fewer dominant species with a high relative abundance. Our study provides information for screening potential degradation bacteria and assessing the risks that oil spills pose to marine ecosystems.

Best available technique for the recovery of marine benthic communities in a gravel shore after the oil spill: A mesocosm-based sediment triad assessment

Ecotoxicological effects of spilled oils are well documented, but study of recovery of marine benthic communities is limited. Long-term recovery of hard bottom communities during physical and biological remediations after a spill was monitored. A 60-day experiment was conducted using a mesocosm with monitoring of eight endpoints by use of the sediment quality triad (SQT). First, physical treatment of hot water + high pressure flushing maximally removed residual oils (max=93%), showing the greatest recovery among SQT variables (mean=72%). Physical cleanup generally involved adverse effects such as depression of the microphytobenthic community during the initial period. Next, biological treatments, such as fertilizer, emulsifier, enzyme and augmentation of the microbes, all facilitated removal of oil (max=66%) enhancing ecological recovery. Analysis of the microbiome confirmed that oil-degrading bacteria, such as Dietzia sp. and Rosevarius sp. were present. A mixed bioremediation, including fertilizer + multi-enzyme + microbes (FMeM) maximized efficacy of remediation as indicated by SQT parameters (mean=47%). Natural attenuation with "no treatment" showed comparable recovery to other remediations. Considering economic availability, environmental performance, and technical applicability, of currently available techniques, combined treatments of physical removal via hand wiping followed by FMeM could be most effective for recovery of the rocky shore benthic community.

The adaptations of the microbial communities of the savanna soil over a period of wildfire, after the first rains, and during the rainy season

Annually, the Cerrado ecosystem alternates between dry periods and long rainy seasons. During the dry season, severe forest fires occur, consuming a considerable part of the native vegetation, which impacts directly on the microbiome of the soil. Evaluate the adaptations of the soil microbiome to drought, rain and wildfire. Sequencing of the 16S rRNA gene was carried out for three significant conditions: drought and forest fires ("Fire"), after the first recorded rains ("First_Rain"), and during the rainy season ("Rainy"). It has been shown that under the "Fire" condition, there was a predominance of Phylum Actinobacteria, followed by Proteobacteria and Firmicutes. With the advent of the rainy season, "First_Rain," there was a change in the predominant taxonomic groups, with a higher prevalence of members of Proteobacteria and Firmicutes. During the rainy season, Proteobacteria and Firmicutes continued as the most prevalent groups. However, it was noted that in this period, there was an increase in bacterial diversity when compared with other periods analyzed. These results show how environmental factors influence adaptations in microbial communities. This allows for a better understanding of how to link the structure of the microbial community to the performance of ecosystems, and assist in preventing the consequences of increased frequency of wildfires, and long periods of drought.

Microbially induced corrosion impacts on the oil industry

The numerous structural impacts on oil installations caused by corrosion make this issue a concern in the oil industry. Although chemical corrosion is relevant in this sector, it is indisputable that the microbial corrosion or bio-corrosion plays a preponderant role, with considerable economic losses. Microbial corrosion invariably depends on the formation of a biofilm on the attacked surface. Biofilm structures provide the conditions that favor the development of microbial groups related to corrosion. Despite the several microbial species are described as corrosive, certain groups, such as sulfate- and nitrate-reducing bacteria, acetogenic bacteria, and methanogenic archaea are the most commonly related. In spite of environmental factors influence the prevalence of certain species, it is increasingly accepted that the relationships between different species are determinant in corrosion. Such relationships can be evidenced by several surveys of microbial communities involved in bio-corrosion. Here, the main microbes related to corrosion in metallic structures used in oil installations are presented, as well as their metabolisms involved in the deterioration of metallic surfaces.

The influence of the marine Bacillus cereus over carbon steel, stainless corrosion, and copper coupons

The present study evaluated the influence of the marine bacteria Bacillus cereus Mc-1 on the corrosion of 1020 carbon steel, 316L stainless steel, and copper alloy. The Mc-1 strain was grown in a modified ammoniacal citrate culture medium (CFA.ico-), CFA.ico- with sodium nitrate supplementation (NO_3-), and CFA.ico- with sodium chloride supplementation (NaCl). The mass loss and corrosion rate were evaluated after the periods of 7, 15, and 30 days. The results showed that in CFA.ico- and CFA.ico- medium added NO_3- the corrosion rates of carbon steel and copper alloy were high when compared to the control. Whereas the medium was supplemented with NaCl, despite the rates being above the averages of the control system, they were considerably below the previous results. In general, the corrosion rates induced by Mc-1 on 316L coupons were below the results compared to carbon steel and copper alloy. When analyzing the corrosion rate measurements, regardless of the culture medium, the corrosion levels decreased consistently after 15 days, being below the levels evaluated after 7 days of the experiment. Our analyses suggest that B. cereus Mc-1 has different influences on corrosion in different metals and environmental conditions, such as the presence of NO_3- and NaCl. These results can help to better understand the influence of this bacteria genus on the corrosion of metals in marine environments.

A latest review on the application of microcosm model in environmental research

Microcosms are used experimentally to simulate ecosystems. This technology has received increasing attention and is widely used for environmental research. This review briefly introduces the origin and development of microcosm theory, summarizes classification and applications of microcosms across decades, and describes the advantages and limitations of microcosm technology in comparison with other methods. Finally, trends in the development of microcosm models are discussed.

Influence of Salt Water Flow on Structures and Diversity of Biofilms Grown on 316L Stainless Steel

Salt water, in addition to being a naturally corrosive environment, also includes factors such as temperature, pressure, and the presence of the microbial community in the environment that influence degradation processes on metal surfaces. The presence or absence of water flow over the metal surfaces is also an important aspect that influences the corrosion of metals. The objective of this study was to evaluate the presence or absence of salt water flow in the formation of biofilms grown in 316L stainless steel coupons. For this, the 316L stainless steel coupons were exposed in two different microcosms, the first being a system with continuous salt water flow, and the second without salt water flow system. The results of the sequencing of the 16S rDNA genes showed a clear difference in structures and diversity between the evaluated biofilms. There was greater abundance and diversity in the "In Flux" system when compared to the "No Flux" biofilm. The analysis of bacterial diversity showed a predominance of the Gammaproteobacteria class in both systems. However, at lower taxonomic levels, there were considerable differences in representativeness. Representatives of Vibrionales, Alteromonadales, Oceanospirillales, and Flavobacteriales were predominant in "No Flux", whereas in "In Flux" there was a greater representation of Alteromonadales, Rhodobacterales, and Saprospirales. These findings help to understand how the flow of water influences the dynamics of the formation of microbial biofilms on metal surfaces, which will contribute to the choice of strategies used to mitigate microbial biofouling.

Comparison of different cultures and culturing conditions for the biological deterioration of organic load from real saline bilge wastewater: microbial diversity insights and ecotoxicity assessment

Bilge wastewater is a high strength, typically saline wastewater, originating from operation of ships. In this study, the treatment of real bilge wastewater was tested using pure isolated aerobic strains and mixed cultures (aerobic and anaerobic). The Chemical Oxygen Demand (COD) and ecotoxicity decrease were monitored over time, while the microbial dynamics alterations in mixed cultures were also recorded. The isolated strains Pseudodonghicola xiamenensis, Halomonas alkaliphila and Vibrio antiquaries were shown to significantly biodegrade bilge wastewater. Reasonable COD removal rates were achieved by aerobic mixed cultures (59%, 9 days), while anaerobic mixed cultures showed lower performance (34%, 51 days). The genus Pseudodonghicola was identified as dominant under aerobic conditions both in the mixed cultures and in the control sample (raw wastewater), after exposure to bilge wastewater, demonstrating natural proliferation of the genus and potential contribution to COD reduction. Biodegradation rates were higher when initial organic load was high, while the toxicity of raw wastewater partially decreased after treatment.

Untapped Potential of Moving Bed Biofilm Reactors with Different Biocarrier Types for Bilge Water Treatment: A Laboratory-Scale Study

Two labscale aerobic moving bed biofilm reactor (MBBR) systems, with a different type of biocarrier in each (K3 and Mutag BioChip), were operated in parallel for the treatment of real saline bilge water. During the operation, different stress conditions were applied in order to evaluate the performance of the systems: organic/hydraulic load shock (chemical oxygen demand (COD): 9 g L−1; hydraulic retention time (HRT): 48–72 h) and salinity shock (salinity: 40 ppt). At the same time, the microbiome in the biofilm and suspended biomass was monitored through 16S rRNA gene analysis in order to describe the changes in the microbial community. The dominant classes were Alphaproteobacteria (families Rhodospirillaceae and Rhodobacteraceae) and Bacteroidia (family Lentimicrobiaceae), being recorded at high relative abundance in all MBBRs. The structure of the biofilm was examined and visualized with scanning electron microscopy (SEM) analysis. Both systems exhibited competent performance, reaching up to 86% removal of COD under high organic loading conditions (COD: 9 g L−1). In the system in which K3 biocarriers were used, the attached and suspended biomass demonstrated a similar trend regarding the changes observed in the microbial communities. In the bioreactor filled with K3 biocarriers, higher concentration of biomass was observed. Biofilm developed on Mutag BioChip biocarriers presented lower biodiversity, while the few species identified in the raw wastewater were not dominant in the bioreactors. Through energy-dispersive X-ray (EDX) analysis of the biofilm, the presence of calcium carbonate was discovered, indicating that biomineralization occurred.

The profile of the soil microbiota in the Cerrado is influenced by land use

Extensive areas of the Cerrado biome have been deforested by the rapid advance of agricultural frontiers, especially by agricultural monocultures, and cultivated pastures. The objective of this study was to characterize the soil microbial community of an environment without anthropogenic interference and to compare it with soybean soil and pasture areas. For that, metagenomic sequencing techniques of the 16S rRNA gene were employed. Consistent changes in the profiles of diversity and abundance were described between communities in relation to the type of soil. The soil microbiome of the native environment was influenced by the pH level and content of Al³⁺, whereas the soil microbiomes cultivated with soybean and pasture were associated with the levels of nutrients N and P and the ions Ca²⁺ and Mg²⁺, respectively. The analysis of bacterial communities in the soil of the native environment showed a high abundance of members of the Proteobacteria phylum, with emphasis on the Bradyrhizobium and Burkholderia genera. In addition, significant levels of species of the Bacillus genus, and Dyella ginsengisoli, and Edaphobacter aggregans of the Acidobacteria phylum were detected. In the soil community with soybean cultivation, there was a predominance of Proteobacteria, mainly of the Sphingobium and Sphingomonas genera. In the pasture, the soil microbiota was dominated by the Firmicutes, which was almost entirely represented by the Bacillus genus. These results suggest an adaptation of the bacterial community to the soybean and pasture cultivations and will support understanding how environmental and anthropogenic factors shape the soil microbial community. KEY POINTS: • The Cerrado soil microbiota is sensitive to impacts on the biome. • Microbial communities have been altered at all taxonomic levels.

The oil spill and the use of chemical surfactant reduce microbial corrosion on API 5L steel buried in saline soil

In order to evaluate the biocorrosion of API 5L metal buried in saline soils, three different conditions in microcosms were evaluated. The control microcosm contained only saline soil, the second had the addition of petroleum, and the third contained the addition of both petroleum and surfactant. The corrosion rate of the metals was measured by loss of mass after 30 days, and the microbial communities were delineated using 16S rRNA gene sequencing techniques. The species were dominated by halophiles in all samples analyzed. Among the bacteria, the predominant group was Proteobacteria, with emphasis on the Alphaproteobacteria and Gammaproteobacteria. Betaproteobacteria and Deltaproteobacteria members were also identified in a smaller number in all conditions. Firmicutes were especially abundant in the control system, although it was persistently present in other conditions evaluated. Bacteroidetes and Actinobacteria were also present in a considerable number of OTUs in the three microcosms. Halobacteria were predominant among archaea and were present in all conditions. The analysis pointed to a conclusion that in the control microcosm, the corrosion rate was higher, while the microcosm containing only oil had the lowest corrosion rate. These results suggest that, under these conditions, the entry of other carbon sources favors the presence of petroleum degraders, rather than samples involved in the corrosion of metals.

Microbial corrosion of DSS 2205 in an acidic chloride environment under continuous flow

Corrosion under flow conditions is a major problem in the transportation industry. Various studies have shown the direct impact of different flow rates on bacteria biofilm formation, mass transfer and resulting different corrosion behaviour of materials in neutral environments. However, little is understood on corrosion under acidic flow conditions. This study investigated the impact of an acidic artificial seawater environment containing Desulfovibrio vulgaris on DSS 2205 microbial corrosion under different velocities (0.25 m.s^-1 and 0.61 m.s^-1). Experiments containing no bacteria were performed as controls. Bacterial attachment was observed by optical and scanning electron microscope (SEM). Materials corrosion was assessed using open circuit potential (OCP), electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization. Pits formed after potentiodynamic test were observed under SEM. The largest area of bacterial attachment was found on coupons immersed at a velocity of 0.25 m.s^-1; however, the corrosion rate was lower than at higher velocity. Shallow pits occurred in the metal coupons when bacteria were present, while deep pits occurred in the controls. The study indicates the positive impact of biofilm formation in corrosion prevention of materials under acidic condition. The nature of corrosion behaviour of duplex stainless is discussed.

Biodegradation and Characterization of Streptomyces sp. (JMCACA3) from Acid Corroded Iron Plate

From acid corroded iron plates five different types of actinobacteria were isolated. Among the five, JMCACA3 strain was selected for the present study. In ISP media, JMCACA3 strain showed well-developed aerial and substrate mycelia were observed. This strain showed good growth in 12 different carbon and 4 different nitrogen sources. The 16S rRNA sequence of phylogenetic analysis by neighbor-joining method identified the studied strain belongs to Streptomyces sp. The biodegradation activity of the strain analyzed by UV and FTIR analysis, which revealed that the various concentrations of Benzimidazole inhibitor with JMCACA3 culture showed slightly varied results. For weight loss method, mild steel coupons incubated with JMCACA3 culture, Benzimidazole inhibitor + JMCACA3 culture and mixed sample showed that JMCACA3 strain utilized the inhibitor as their energy source and the weight the coupons were slightly varied, evidenced by XRD spectra and showed Fe₂O₃ corrosion products. Our study concluded that the JMCACA3 strain, an iron-reducing actinobacteria which utilizes and converted the corrosion inhibitor Benzimidazole as their energy source. So, it is very urgent to develop more powerful corrosion inhibitor from green biocide or microbial-based biocide and their analog which incorporated into the pre-existing Benzimidazole to increase the corrosion inhibitor level against the biofilm of actinobacterial influenced corrosion.

Influence of Acidification and Warming of Seawater on Biofouling by Bacteria Grown over API 5L Steel

The acidification and warming of seawater have several impacts on marine organisms, including over microorganisms. The influence of acidification and warming of seawater on biofilms grown on API 5L steel surfaces was evaluated by sequencing the 16S ribosomal gene. For this, three microcosms were designed, the first simulating the natural marine environment (MCC), the second with a decrease in pH from 8.1 to 7.9, and an increase in temperature by 2 °C (MMS), and the third with pH in around 7.7 and an increase in temperature of 4 °C (MES). The results showed that MCC was dominated by the Gammaproteobacteria class, mainly members of the Alteromonadales Order. The second most abundant group was Alphaproteobacteria, with a predominance of Rhodobacterales and Oceanospirillales. In the MMS system there was a balance between representatives of the Gammaproteobacteria and Alphaproteobacteria classes. In MES there was an inversion in the representations of the most prevalent classes previously described in MCC. In this condition, there was a predominance of members of the Alphaproteobacteria Class, in contrast to the decrease in the abundance of Gammaproteobacteria members. These results suggest that possible future climate changes may influence the dynamics of the biofouling process in surface metals.

Supplementary Information

The online version contains supplementary material available at 10.1007/s12088-021-00925-7.

Bacterial community analysis of biofilm on API 5LX carbon steel in an oil reservoir environment

This study aimed to characterize the biofilm microbial community that causes corrosion of API 5LX carbon steel. API 5LX carbon steel coupons were incubated with raw produced water collected from two oil reservoir stations or filter-sterilized produced water. Biofilm 16S rRNA amplicon sequencing revealed that the bacterial community present in the biofilm was dominated by Proteobacteria, including Marinobacter hydrocarbonoclaustics and Marinobacter alkaliphilus. Electrochemical analysis such as impedance and polarization results indicated that Proteobacteria biofilm accelerated corrosion by ~ twofold (2.1 ± 0.61 mm/years) or ~ fourfold (~ 3.7 ± 0.42 mm/years) when compared to the control treatment (0.95 ± 0.1 mm/years). Scanning electron and atomic force microscopy revealed the presence of a thick biofilm and pitting corrosion. X-ray diffraction revealed higher amounts of the corrosion products Fe₂O₃, γ-FeOOH, and α-FeOOH, and confirmed that the microbial biofilm strongly oxidized the iron and contributed to the acceleration of corrosion of carbon metal API 5LX.