Numeric simulation of bone remodelling patterns after implantation of a cementless straight stem

Three-year follow-up of changes of cortical bone thickness after implantation of Endo-Exo-Prosthesis (EEP) for transfemoral amputees

Introduction

Transcutaneous Osseointegrated Prosthetic Systems (TOPS) offer a good alternative for patients who cannot be satisfactorily rehabilitated by conventional suspension sockets. The Endo-Exo-Prothesis (EEP, ESKA Orthopaedic Handels GmbH®, Deutschland) is the most implanted TOPS in Germany. Previous studies have shown that cortical thickness increases after implantation of TOPS. The aim of this study is to determine changes of cortical thickness in relation to the time after implantation of the Endo-Fix-Stem.

Patients and methods

All transfemoral amputees treated by EEP from 2007 to 2013 were operated by the last author of this study. X-ray images of 4 follow-up intervals (postoperative, 3 months, 12 months, 3 years) were analyzed retrospectively. The femoral residuum was divided into 3 sections (proximal, middle, distal) with 2 measuring points in each section: medial and lateral. Cortical thickness was measured at these 6 points and compared at regular intervals using the Friedman test for non-parametric dependent variables.

Results

Thirty-seven patients with 40 implants were included. The average age was 52.2 years (30–79 years). 83.7% of the patients were male. No statistical significance could be shown for any of the measuring points of the femoral residual (proximal medial, proximal lateral, middle medial, middle lateral, distal medial, distal lateral) among the mean values of the cortical thickness at the different follow-up times (p > 0.05 for all measuring points). Cortical remodeling processes (> 1 millimeter (mm)) occurred in all implants despite a missing statistical significance. Hypertrophy could be confirmed for 42.5% and atrophy for 37.5%. Twenty percent of the cases showed a parallel occurrence of both entities. Cortical changes greater than 5 mm were only observed at the distal end of the femur.

Conclusion

Even if our results did not show any significant difference, it can be deduced that the osseointegration process leads to a remodeling of the bone structure, both in terms of increased bone formation and bone resorption. However, it has not yet been conclusively clarified which processes lead to hyper- or atrophy. The force transmission between prosthesis and bone and the facultative bacterial colonization of the stoma are still the main factors which may be responsible for the bone remodeling processes.

'Pre-launch' finite element analysis of a short-stem total hip arthroplasty system consisting of two implant types

BACKGROUND

We applied a previously established and validated numerical model to a novel short-stemmed implant for a 'pre-launch' investigation.

METHODS

The implant system consists of two different implant geometries for valgus/varus-positioned proximal femurs with differences in volume distribution, head/neck angle, and calcar alignment. The aim of the design was to achieve a better adaption to the anatomic conditions, resulting in a favourable load transfer. The implant type G showed the best fit to our model, but both stem geometries were implanted; the implant type B was used to compute an 'imperfection scenario'.

FINDINGS

Apparent bone density decreased by 4.3% in the entire femur with the implant type G, and by 12.3% with the implant type B. Bone mass loss was pronounced in the proximal calcar region. Apparent bone density increased at the lateral cortical ring and in the minor trochanter. The apparent bone density in the imperfection scenario was very similar to that of a straight stem, indicating a distal load transfer.

INTERPRETATION

No adverse effects of the A2 short-stemmed implant system on bone remodeling could be detected. The overall bone density reduction was acceptable, and wedge fixation was not observed, indicating that there was no distal load transfer. The simulation of an incongruous implant indicates the sensitivity of our model in response to modifications of implant positioning. Correct implant selection and positioning is crucial when using the A2 system.

Initial Stability of Subtrochanteric Oblique Osteotomy in Uncemented Total Hip Arthroplasty: A Preliminary Finite Element Study

BACKGROUND

Subtrochanteric oblique osteotomy (SOO) has been widely used to reconstruct highly dislocated hips in uncemented total hip arthroplasty. The occurrence of complications can be attributed to the instability of the osteotomy region. The aim of this study was to evaluate the initial stability of SOO in uncemented total hip arthroplasty.

MATERIAL AND METHODS

A 3-dimensional finite element femur-stem model was created, and a virtual SOO was performed at 4 oblique angles: 30°, 45°, 60°, and 90°. The von Mises stress distribution in the femur-stem complex and the displacement under different oblique angles were evaluated in the SOO models, in comparison with that of the intact model.

RESULTS

The study demonstrated that the distal fragment of the femur bore more stresses than the proximal fragment, and the maximum stress was concentrated in the femoral neck and the cortical bone, which contacted with the distal end of the stem. SOO increased the stress of both the femur and the stem, and fractures may occur in the stress concentration sites. Additionally, comparing the displacement at different oblique angles, the lateral region was larger than that of the medial region on the subtrochanteric osteotomy plane. The minimum micromotion on the osteotomy plane was obtained when the oblique angle was 45°.

CONCLUSIONS

The fit and fill of the distal fragment of the femur and the stem is essential for the stability of the subtrochanteric osteotomy region. The optimal oblique angle for SOO appears to be 45°.