Preparation and adhesion performance of transparent acrylic pressure-sensitive adhesives containing menthyl acrylate

Polymers without Petrochemicals: Sustainable Routes to Conventional Monomers

Access to a wide range of plastic materials has been rationalized by the increased demand from growing populations and the development of high-throughput production systems. Plastic materials at low costs with reliable properties have been utilized in many everyday products. Multibillion-dollar companies are established around these plastic materials, and each polymer takes years to optimize, secure intellectual property, comply with the regulatory bodies such as the Registration, Evaluation, Authorisation and Restriction of Chemicals and the Environmental Protection Agency and develop consumer confidence. Therefore, developing a fully sustainable new plastic material with even a slightly different chemical structure is a costly and long process. Hence, the production of the common plastic materials with exactly the same chemical structures that does not require any new registration processes better reflects the reality of how to address the critical future of sustainable plastics. In this review, we have highlighted the very recent examples on the synthesis of common monomers using chemicals from sustainable feedstocks that can be used as a like-for-like substitute to prepare conventional petrochemical-free thermoplastics.

Influence of Methacrylate and Vinyl Monomers on Radical Bulk Photopolymerization Process and Properties of Epoxy-Acrylate Structural Adhesives

In this paper, epoxy-acrylate structural adhesives tapes (SATs) were obtained from Bisphenol A-based liquid epoxy resin and epoxy acrylic resins (EARs). A new method of EARs preparation, i.e., the free radical bulk photopolymerization process (FRBP), was studied in detail. The influence of methacrylic monomers (methyl methacrylate, ethyl methacrylate, butyl methacrylate, lauryl methacrylate, (2-acetoacetoxy)ethyl methacrylate) and vinyl monomers (N-vinylpyrrolidone and styrene) on the FRBP process of base monomers (i.e., butyl acrylate, glycidyl methacrylate and 2-hydroxyethyl acrylate) was investigated. The kinetics of photopolymerization process was monitored by photo-differential scanning calorimetry method. The properties of the obtained EARs (viscosity and average molecular weights), as well as monomers conversion using ¹H NMR, were determined. It was revealed that styrene significantly decreases the photopolymerization rate and increases the final monomers conversion (+27%). However, the resulting tetrapolymers BA-co-GMA-co-HEA-co-STY have low molecular weights and low polydispersity (2.2). Methacrylate monomers with shorter aliphatic chains (<C₄) also decrease the rate of photopolymerization due to the length of the aliphatic chain increasing. Surprisingly, the best results of adhesion to steel and shear strength were obtained for SAT based on epoxy acrylate resin with styrene (11 N/25 mm and 20.8 MPa, respectively). However, the thermomechanical properties of SAT with styrene were weaker than those with methacrylates.

The Effect of Type-I Photoinitiators on the Kinetics of the UV-Induced Cotelomerization Process of Acrylate Monomers and Properties of Obtained Pressure-Sensitive Adhesives

A new method of solvent-free acrylic pressure-sensitive adhesives (PSAs) based on UV-induced cotelomerization products was presented. The key acrylic monomers (i.e., n-butyl acrylate and acrylic acid) with copolymerizable photoinitiator 4-acrylooxybenzophenone in the presence of a selected chain transfer agent (tetrabromomethane, TBM) were used in the UV-cotelomerization process. Moreover, two kinds of UV-photoinitiators (α-hydroxyalkylphenones, HPs and acylphosphine oxides, APOs) were tested. Photo-DSC, viscosity, thermogravimetric, and GPC measurements for cotelomers were performed. The kinetics study revealed that the systems with APOs, especially Omnirad 819 and Omnirad TPO, were characterized by a much higher reaction rate and greater initiation efficiency than HPs systems were. Additionally, the APO-based syrups exhibited a higher solid content (ca. 60–96 wt%), a higher dynamic viscosity (5–185 Pa·s), but slightly lower molecular weights (M_n and M_w) compared to HP syrups. However, better self-adhesive features (i.e., adhesion and tack) were observed for PSAs based on cotelomers syrups obtained using APOs with lower solid contents (55–80 wt%). It was found that as the solids content (i.e., monomers conversion) increased the adhesion, the tack and glass transition temperature decreased and the type and amount of photoinitiator had no effect on polydispersity. Most of the obtained PSAs were characterized by excellent cohesion, both at 20 °C and 70 °C.

Epoxy-Based Structural Self-Adhesive Tapes Modified with Acrylic Syrups Prepared via a Free Radical Photopolymerization Process

New modifiers (i.e., acrylic syrups; ASs) of epoxy-resin-based thermally curable structural self-adhesive tapes (SATs) were prepared via a free radical bulk polymerization (FRBP) of n-butyl acrylate, butyl methacrylate, glycidyl methacrylate, and hydroxybutyl acrylate. In the process, two kinds of UV-photoinitiators (i.e., monoacylphosphine oxide/Omnirad TPO and bisacylphosphine oxide/Omnirad 819) and various mixing speed of the monomers mixture (200–1000 rpm) were applied. The TPO-based syrups exhibited a lower copolymers content (10–24 wt%), dynamic viscosity (<0.1 Pa·s), molecular weights (M_n and M_w, and polydispersity (1.9–2.5) than these with Omnirad 819. Additionally, the higher mixing speed significantly reduced monomers conversion and viscosity of ASs as well as molecular weights of the acrylate copolymers. These parameters influenced the properties of thermally uncured (e.g., adhesion) and thermally cured SATs (shear strength of aluminum/SAT/aluminum overlap joints). Better self-adhesive features were observed for SATs-TPO (based on ASs with lower monomers conversion, M_n and M_w); however, a slightly higher shear strength was noted for the thermally cured SAT-819 (ASs with higher monomers conversion, M_n and M_w). An impact of polydispersity of the acrylate copolymers as well as crosslinking degree of thermally cured SATs on the mechanical strength was also revealed.

Influence of Acrylic Acid on Kinetics of UV-Induced Cotelomerization Process and Properties of Obtained Pressure-Sensitive Adhesives

A new environmentally friendly method of photoreactive pressure-sensitive adhesives (PSAs) preparation was demonstrated. PSAs based on n-butyl acrylate (BA), acrylic acid (AA) and 4-acryloyloxy benxophenone (ABP) were prepared via the UV-induced cotelomerization process in the presence of a radical photoinitiator (acylphosphine oxide) and telogen (tetrabromomethane). Hydroxyterminated polybutadiene was used as a crosslinking agent. Influence of AA concentration (0-10 wt %) on kinetics of the cotelomerization process was investigated using a photodifferential scanning calorimetry method, selected physicochemical features of obtained photoreactive BA/AA/ABP cotelomers (molecular masses, polydispersity, monomers conversion and dynamic viscosity) and self-adhesive properties of obtained PSAs (adhesion, tack and cohesion) were studied, as well. It turned out that AA content is the important factor that influences monomers conversion (thereby the volatile parts content in prepolymer) and PSAs' properties. As the acrylic acid content increases, the reaction rate increases, but the total monomers conversion and the solid content of the prepolymer decreases. Additionally, the adhesion and cohesion of PSAs were grown up, and their tackiness decreased. However, the AA content has no effect on molecular weights (Mw and Mn) and polydispersity (c.a. 1.5) of photoreactive cotelomers. The optimal AA content necessary to obtain a prepolymer with low volatile parts content and good PSA properties was determined.

Free-Radical Bulk-Photopolymerization Process as a Method of Obtaining Thermally Curable Structural Self-Adhesive Tapes and Effect of Used Type I Photoinitiators

A new fabrication method for thin (120 µm) thermally curable structural self-adhesive tapes (SATs) was demonstrated by utilizing a series of acrylic syrups (ASs) modified using Bisphenol A-based liquid epoxy resin. The acrylic syrups containing poly(butyl acrylate-co-butyl methacrylate-co-glycidyl methacrylate-co-2-hydroxyetyl acrylate-co-4-acryloyloxy benzophenone) were synthesized via free-radical bulk-photopolymerization (FRBP) process. Influence of different type I radical photoinitiators (PIs), i.e., α-hydroxyalkylphenones (HPs), acylphosphine oxides (APOs) and its mixtures (HPs/APOs and APO/APO) on selected physico-chemical features of obtained ASs was studied. It turned out that APO-type PIs are more effective in the FRBP process (NMR studies). Self-adhesive tests of SATs revealed that the monomers’ conversion in ASs have a significant influence on adhesion and tack. Moreover, the polymer structures formed at the UV cross-linking stage of SATs significantly affect the cross-linking degree of SATs during thermal curing (differential scanning calorimetry method). The highest values of overlap shear strength were achieved by SATs based on ASs with monomers’ conversion on the level 50–60%.

Synthesis and polymerization of bio-based acrylates: a review

Acrylates and polyacrylates have been produced massively due to their interesting applications like Plexiglas.

Influence of Phase Separation on Performance of Graft Acrylic Pressure-Sensitive Adhesives with Various Copolyester Side Chains

Acrylic pressure-sensitive adhesives with various polyester side-chain lengths were synthesized to investigate the effect of branching on phase separation and polymer mechanical performance. The polyester macromonomers (MMs) were produced through ring-opening co-polymerizations of l-lactide (l-LA) and ε-caprolactone (ε-CL) initiated with 2-hydroxyethyl methacrylate (HEMA), which provides the polyester chains with terminal vinyl groups. By varying the HEMA content, a range of MM chain lengths constructed from L₁₀C₄ (five l-LA and four ε-CL units) to L₁₀₀C₄₀ were obtained at a constant monomer mole ratio. Copolymerization of 2-ethylhexyl acrylate and acrylic acid with these MMs at constant mass composition provided a series of comb copolymers consisting of acrylic backbones with polyester branches of various chain lengths. Characterization of thin films cast from the polymers using thermal analysis and scanning probe microscopy showed a transition from a homogeneous phase to the formation of distinct microphases with increasing branching chain lengths. Rheological analysis of the linear viscoelastic responses was also used through small-amplitude oscillatory shear, and dynamic master curves were constructed by time-temperature superposition. The rheological data were also consistent with phase separation for the longer side-chain lengths of L₅₀C₂₀ and L₁₀₀C₄₀. The extra elastic contribution at low frequency and the temperature dependence of a _T both show obviously effect of separated phases. Performance testing of polymer films showed that the chain extension resulted in a significant increase in both peel strength and shear resistance, which was accompanied by a modest decrease in film tackiness. The results demonstrate that tailoring branch chain structures provide a promising means for controlling the properties of the high-biomass content adhesive polymers.